Now that the common code supports the syscall trace level, change the
Blackfin code from using the event level to the syscall level.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Pull the model data (register addresses/sizes) out of the different model
files and into the machs.h header. The models themselves don't care about
where they're mapped, only the mach code does. This allows us to keep the
model headers from being included in the mach code which can cause issues
with model-specific names colliding. Such as when a newer device model is
created, but with incompatible register names/layouts.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The UART has a LOOP_ENA bit in its MCR register where writes to the THR
go to the RBR. Implement support for this mode.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
A few bits in the newer UART LSR register are not sticky, so make sure
we clear them when returning updated status rather than leaving them
always set.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Make all of the pins bidirectional, and support sending signals when
software drives the pins as outputs.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
When the mask a/b MMRs are written, the output signal might change levels
(as pins are [un]masked), so make sure we update the output level.
Further, make sure we handle edge ints correctly by first sending a high
signal followed by a low signal.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
A bunch of 32bit insns were not using the store buffer, so when they were
used in parallel insns, they would incorrectly clobber a register early.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
When most video related insns are used in parallel with Ireg loads, the
DISALGNEXCPT insn behavior is implicitly in effect.
Reported-by: Anton Shokurov <shokurov.anton.v@yandex.ru>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The SIC latches ints from peripherals to the CEC, but the peripherals
need to be able to tell the SIC when to stop. So use the incoming level
to figure out when to set the int bits and when to clear it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This doesn't currently generate any interrupts (as there doesn't appear
to be any documentation to *when* it would even do so), but since the
HRM does say an interrupt line exists between the OTP and the SIC, add
one for completeness sake. This will make a follow up patch easier.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The current implementation attempts to handle the 16bit sign extension
itself. Unfortunately, it gets it right in some cases. So rather than
fix that logic, just drop it in favor of using 16bit signed casts. Now
gcc will take care of getting the logic right.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The current handling of the subtraction insn with the RND12 modifier
works when saturation isn't involved. So add handling for this edge
case to match the hardware.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The 16bit add/sub insns missed setting the VS bit in ASTAT whenever the
V bit was also set.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Makes it a lot easier to find out what's going on with interrupt lines
if the ports have tracing output.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We need the DIR bit cleared, not set, in order for the pin to be treated
as an input.
When looking up the data value, we need to shift the "level" value over by
"my_port" rather than "bit" as the latter has already been shifted over.
We also should normalize the "level" coming in from the outside worlds to
the set of {0,1} since those are the only values that matter to GPIOs.
We need the BOTH bit set, not cleared, in order for the pin to trigger
on both edges.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The clear/set/toggle MMRs aren't backed by "real" data; they implicitly
perform bit operations on the associated data register. So when we go
to process writes to them, we need to adjust the pointer accordingly so
that the actual backing data is modified.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
When I originally wrote the w1c helper funcs, I used it in a few places.
Then I forgot how it worked and when I later documented it, I described
the 3rd arg in the exact opposite way it is actually used. This error
propagated to a bunch of devices registers that were not explicitly
tested (a bunch of the devices are stubs which merely exist to say "no
device is connected" to make device drivers happy).
So once the documentation is unscrewed, fix all of the broken call sites.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We'll need these bits in an upcoming patch, so map out the whole
LSR MMR now.
Fix up indentation style while we're here.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The Blackfin PRM says that the top 8 bits of the accumulator must be
cleared when using the VIT_MAX insn, so the sim has followed this spec.
Matching the hardware behavior though when the high bits are not cleared
is easy to do and doesn't break existing behavior, so go for it.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The Blackfin PRM does not cover this case, but the hardware is clear: even
if the search criteria is not met (and thus a new 16bit value is loaded up
into the accumulator), the accumulator undergoes 16bit sign extension. So
simply reload the low signed 16bits in that case.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The Acc=-Acc insn can overflow or carry with edge values, so make sure
we update the ASTAT bits accordingly to match the hardware. Also fix
a thinko where we always updated AC0 even when working with A1 regs.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
When encoding the SIC/pin info into unique input port ids, I used bases
of 100 when I meant to use 0x100. Rather than simply fix the decoding
math in the different functions, create a few helper macros to simplify
the SIC/pin encoding and decoding steps. This makes the resulting tables
nice & clear.
And now that pins are clear, the 533 and 537 port_event handlers may
easily be merged into one.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The hardware allows the byteop[123]p insns to use the same src reg pair,
so remove the combination check in the sim.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The bus addresses have to be valid numbers, so 'g' and 'h' won't work.
Oddly, the common code silently ignored this which is why I didn't notice
in the first place.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We weren't updating AZ when doing a 16bit add or sub insn. Implement it.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
No point in moving unchanged acc values to the acc regs, and avoid
updating the acc ASTAT bits when only reading. This fixes incorrect
changing of the ASTAT bits when they're only being read.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The current dsp mult handler does not take care of overflows which turn
values negative (and thus set AN in ASTAT). So implement it.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The current dsp mult handler does not take care of overflows and updating
the V ASTAT bit. So implement it.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
When testing ASTAT regs, specific bit differences carry a lot more meaning
than when checking the value of a data register. So automatically decode
the bits of the two values and print things out so that people don't have
to manually do it themselves every time.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The saturation behavior with fract modes differs from non-fract modes.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This can boot Das U-Boot and a Linux kernel. It also supports Linux
userspace FLAT and FDPIC (dynamic and static) ELFs.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
