* Add support for STM32L0/L1 onboard EEPROM.
* Update docs/eeprom_driver.md
Co-Authored-By: Joel Challis <git@zvecr.com>
Co-authored-by: Joel Challis <git@zvecr.com>
* Add buffer based single line pan, arbitrary byte write to buffer
* Change dirty mask to inverse of OLED_BLOCK_TYPE for future proofing larger buffer sizes
* Updating docs to include new functions
* Updating to clarify scroll vs pan
* Fix out of bound OLED font access
The default font is 1344 bytes, or a total of 224 glyphs (each 6-bytes wide).
OLED_FONT_END defaults to 224, which if used will then index off the end of
the font array. So either the documentation or code is wrong.
Instead of figuring out the rewording of the documentation, just change
the OLED_FONT_END default value to 223, to match the documentation and code.
* Add static assert to check array size
Build bomb if the font array size doesn't match to the defines.
- uprintf -> dprintf
- Fix atsam "vendor" eeprom.
- Bump Kinetis K20x to 64 bytes, too.
- Rollback Kinetis to 32 bytes as partitioning can only be done once. Add warning about changing the value.
- Change RAM-backed "fake" EEPROM implementations to match eeconfig's current usage.
- Add 24LC128 by request.
* Run clang-format manually to fix recently changed files
* Run clang-format manually to fix recently changed files - revert template files
* Run clang-format manually to fix recently changed files - format off for ascii_to_keycode_lut
* Add i2c_transmit_receive function
This function is listed in the ARM header file, but doesn't actually exist.
* Remove i2c_transmit_receive function
* Update DRV2605L read function to use i2c_readReg on both arm and avr
* Add central location for chibios defines
* Add central location for chibios defines - actually add files this time....
* Add Copyright header
* Update include order to resolve i2cv1 build errors
* Improve support and docs for ADC driver
* Comment ADC channels
* Move to Makers and Modders section, and fix usage instructions
* Flesh out intro
* Superscript 328P note
* Fix pin_to_mux LUT
* Support USB64/1287 as well
* analogReadPin() defaults to 0V mux on invalid pin
* Update pinToMux() function documentation
* Dot
* Accept (some of) the `qmk cformat` changes
* Do clang-format properly
* More wording tweaks
* Link to encoder docs
* IS31FL3733 Dirty page fix
Function IS31FL3733_update_led_control_registers was never setting update register to false. As a result the led on/off page was being written every transaction even when it was not modified. This is ineficient and causes lots of bandwidth use.
-> Fix the IS31FL3733_update_led_control_registers.
-> After testing it was evident that failed I2C transactions could corrupt the Led on/off register.
-> Update IS31FL3733_write_pwm_buffer and IS31FL3733_write_register functions to return 0 upon succesful tranmission and 1 if any of the transmitions within the function fail.
-> Modify IS31FL3733_update_pwm_buffers function so if any of the IS31FL3733_write_pwm_buffer transuction fails, the g_led_control_registers_update_required register is set to true forcing a rewrite of the led on/off register in case it was corrupted.
* Minor comment update
* Upsie:)
* Update is31fl3733.c
* Return fix
* more return fix
* type change
* more boolian logic reversal:)
* Error out when Solenid pin is not defined
Instead of defaulting to a (literally) random pin, error out instead. Because this pin may be used, or because that pin may not be exposed, or may not exist.
* Remove 'SOLENOID_ACTIVE' setting since it's not used
* Update documentation
* Move Ergodox EZ RGB code to custom driver
Also implements full addressing of Ergodox EZ's LED Strip, as written by seebs
Co-authored-by: Seebs <seebs@seebs.net>
* Make Clipping range accessible for custom drivers
* Remove RGBW_BB_TWI from driver and docs
* Revert changes to clipping range support
* Use just rgblight_set instead of full custom driver
* Convert to i2c_master commands
* Rename rgblight driver and clean up includes
* Fix unicode in comments
Co-Authored-By: fauxpark <fauxpark@gmail.com>
* Remove separate RGBW implementation for a unified function
* Set White to 0 in RGBW LEDs
This is just to get this working, later, proper brightness can be handled elsewhere.
* Use us instead of nanoseconds(?) since it renders correctly on web
* Remove RGBW function from arm/ws2812.h
* Remove RGBW function from arm/ws2812.c
* Formatting changes
* Add doc info
* Initial ARM bitbang ws2812 driver
* Unify chibios platform to run rgblight_task
* Remove 'avr only' comments from ws2812 docs
* Remove 'avr only' comments from ws2812 docs
* Unify chibios platform to run rgblight_task - review comments
* Remove debug flags from keymap
* Add comments from review
* Add defines for STM32L0XX
* Attempt to get arm ws2812 working on multiple gcc versions
It was beleaved that this setting result in a 400Khz I2C bus.
This was incorrect, actual frequency measure with a logic analyzer was around 150Khz.
This is derived from the excel sheet linked in the .h file.
Also confirmed with the ST IDE.
* Began Work On STM32 Ergodox
Changes to be committed:
new file: keyboards/ergodox_stm32/config.h
new file: keyboards/ergodox_stm32/rules.mk
* test
* Now it compile. Not linking thou
* Screw this Linker. It links now!
* Blinkly Keyboard
* bootloader test code
* Working on matrix / i2c stuff
* Progress (LED Blink)
* Progress on MCP_23017 Status Flag
* [WIP]
* update
* Works! Remeber to change back the bootloader address when the new bootloadrer is ready.
* Time to go debug the i2c
* Finally, it now works with PCB Rev 1.0.2
* updated for rev.2 pcb
* minor compilation fix
* Why when debugger is enabled then everything works.
* Remeber to call init functions.
* Update arm i2c driver to support STM32F103 series device.
* fix include once header. Replaced with #pragma once.
* complication test
* provide means to turn on RTP mode and set the amplitude
* new keycode HPT_CONT to turn RTP off/on
* introduce new keycodes HPT_CONI, and HPT_COND for Haptic Continuous Increase and Decrease
* support for continuous mode amplitude increase and decrease
* code cleanup
* update docs to reference new keycodes and functionality
* don't touch the keymaps
* add function prototypes
* add proper guards
* cleanup guards
* remove extra reserved
* Fix battery level code in adafruit_ble.cpp
The code in tsk_core/protocol/lufa/adafluit_ble.cpp that polls the
battery level for the Adafruit feather BLE controller reads the
regulated voltage, not the raw voltage coming from the battery. To do
that, the Adafruit Feather docs say you should read from pin A9:
https://learn.adafruit.com/adafruit-feather-32u4-basic-proto/power-management#measuring-battery-4-9.
(See also
https://learn.adafruit.com/adafruit-feather-32u4-bluefruit-le/pinouts#logic-pins-2-9.)
I'm not sure why, but analogRead(9); doesn't read the correct pin.
Checking all available analog pins experimentally, it turns out that
analogRead(7); returns the correct value. So the code above should read:
state.vbat = analogRead(7);
* Update tmk_core/protocol/lufa/adafruit_ble.cpp
Co-Authored-By: Drashna Jaelre <drashna@live.com>
* Remove old comment
* Fix linking error
* Remove `#ifdef` around `#include analog.h`.
* Really fix linking error
Currently OLED Dirver only supports LF (\n) character in a string to clear out the rest of the current line and advance to the next line for writing. This PR adds support for CR (\r) character as well to advance to the next line, however not clear out the rest of the current line. This is extremely useful when you want to display a multi-line logo using a single array without wiping out exiting lines and flagging the OLED as dirty unnecessarily.
Using QUANTUM_LIB_SRC prevents the warning when multiple sources add the i2c_master.c file. Boards such as the Ergodox EZ Glow see this warning every time they compile because the board uses the file in general, and because the RGB LED Matrix requires it, as well.
* modify oled_driver to support SH1106
also:
- improve mechanism to specify which OLED IC we use
- comment calc_bounds()
- give OLED_COLUMN_OFFSET a default value
- inline comment re: OLED MEMORY_MODE and SH1106
- update docs/feature_oled_driver.h for SH1106 support and related changes
- docs: OLED: note we have tested SSD1306 on ARM boards (per @XScorpion2)
- define out MEMORY_MODE when using SH1106 OLED driver
* document that SSD1306 128x64 on AVR works
Per @XScorpion2: https://github.com/qmk/qmk_firmware/pull/5787#discussion_r291837842
I2C timing parameters were seemingly set up for an STM32F303 target MCU, at a specific clock speed. This commit allows specifying the timing parameters via config.h, allowing other STM32 MCUs to be targeted, potentially at different clock frequencies.
Alternate function modes for the I2C pins are now also configurable, allowing for remapping to other pins.
* RGB Matrix overhaul
Breakout of animations to separate files
Integration of optimized int based math lib
Overhaul of rgb_matrix.c and animations for performance
* Updating effect function api for future extensions
* Combined the keypresses || keyreleases define checks into a single define so I stop forgetting it where necessary
* Moving define RGB_MATRIX_KEYREACTIVE_ENABLED earlier in the include chain
* Adds the Planck EZ, 3737 RGB, fixes out-of-tune notes
* fix bug in quantum/rgb_matrix_drivers.c
Co-Authored-By: jackhumbert <jack.humb@gmail.com>
* update command setting to the correct default
* correct rgb config
* remove commented-out lines
* update docs for the 3737
* Update docs/feature_rgb_matrix.md
Co-Authored-By: jackhumbert <jack.humb@gmail.com>
* On i2c_init, enable two wire interface, twi interrupt, and slave
address ACK along with pull up resistors.
* thanks to some testing by drashna, we know that setting TWI doesn't work for all boards. Putting the new code into an ifdef block
* initial work to add eeprom to haptic feedback and decouple the feedback process from keyboards
* Haptic feedback enhancements: on/off toggle working, feedback order working
todo:
-work on modes switching
-get modes switching to save to eeprom
* haptic enhancement - eeprom and modes added
* Added set and get functions for haptic feedback
* initial implementation of solenoids under haptic feedback
* changed eeprom to 32 bits to reserve blocks for future features
* start documentation of haptic feedback
* change keycode per comment from reviewers
* typo fixes
* added eeprom for solenoid configs
* added solenoid and docs
* Add/fix default parameters configs, improve docs
* more doc cleanup
* add in solenoid buzz toggle, clean up doc
* some fixes for error in compiling solenoid
* fix a chibios specific i2c read function and added one for AVR controllers in DRV2605L.c
* fixes for avr side issues
* update keymap
* fix keymap compile error
* fix bugs found during solenoid testing
* set pin that is not powered during bootloader
* added warning about certain pins on the MCU may trip solenoid during DFU/bootloader
* Add stm32f072 base ck4x4 to handwired
* add prints
* Save these tries
* Save changes again
* Working hadron oled
* OLEd working but ws2812b still iffy:
* save another try
* Encoder feature + OLED
* RTC code
* Implement clock setting mode
* Whitespace
* Encoder hooked up to working LED PWM code
* Add missing files
* eeprom changes
* Save changes
* Move i2c master
* Move satisfaction75 under cannonkeys
* Set proper default folder
* Revert some core changes
* Undo paved iris changes
* Reorganize code for maintainability and prep for new features
* Add starting code for clock OLED mode
* Clock set mode finished
* Add custom encoder modes
* Actually add VIA keymap
* Gate to only 072
* fix gate for only 072
* Update header guards and includes
* Update i2c selection strategy
* Update board.c to handle software reset to DFU
* adds proton c base
* fixes custom matrix include
* adds readme.md
* initial proton coversion, no pin mapping
* start of mcu selection
* add pin mapping and sweet16 test
* add at90 to list
* disable backlight, fix d7
* update flag names
* doc updates
* proton c update for mcu selection
* initial commit, this now mostly works
- RGB controls work
- Dynamic keymap still broken due to eeprom
- Via works
* STM32 eeprom update
- Update EEPROM emulation library to handle 8bit data like AVR.
- This library also allows for multiple page pairs resulting in greater EEPROM size flexibility
* hs60 changes
* HS60 hhkb added
* Update keyboards/hs60/v2/config.h
Co-Authored-By: yiancar <yiangosyiangou@cytanet.com.cy>
* add initial support for hadron ver3
* add initial support for hadron ver3
* pull qwiic support for micro_led to be modified for use in hadron's 64x24 ssd1306 oled display
* initial work on OLED using qwiic driver
* early work to get 128x32 oled working by redefining qwiic micro oled parameters. Currently working, but would affect qwiic's micro oled functionality
* moved oled defines to config.h and added ifndef to micro_oled driver
* WORKING :D - note, still work in progress to get the start location correct on the 128x32 display.
* added equation to automatically calculate display offset based on screen width
* adding time-out timer to oled display
* changed read lock staus via read_led_state
* lock indications fixes
* Added scroll lock indication to oled
* add support for DRV2605 haptic driver
* Improve readabiity of DRV2605 driver.
-added typedef for waveform library
-added unions for registers
* Update keyboards/hadron/ver2/keymaps/default/config.h
Co-Authored-By: ishtob <ishtob@gmail.com>
* Update keyboards/hadron/ver2/keymaps/default/config.h
Co-Authored-By: ishtob <ishtob@gmail.com>
* Update keyboards/hadron/ver2/keymaps/default/config.h
Co-Authored-By: ishtob <ishtob@gmail.com>
* Update keyboards/hadron/ver2/keymaps/default/config.h
Co-Authored-By: ishtob <ishtob@gmail.com>
* Fixes for PR
* PR fixes
* fix old persistent layer function to use new set_single_persistent_default_layer
* fix issues with changing makefile defines that broken per-key haptic pulse
* Comment fixes
* Add definable parameter and auto-calibration based on motor choice
* I2C driver docs
- Added I2C driver docs.
- Changed arm master i2c driver to have a weak i2c_init as it is impossible to account for all possible port configuration in the STM32 world.
* Update docs/i2c_driver.md
Co-Authored-By: yiancar <yiangosyiangou@cytanet.com.cy>
* Update docs/i2c_driver.md
Co-Authored-By: yiancar <yiangosyiangou@cytanet.com.cy>
* Update docs/i2c_driver.md
Co-Authored-By: yiancar <yiangosyiangou@cytanet.com.cy>
* Update docs/i2c_driver.md
Co-Authored-By: yiancar <yiangosyiangou@cytanet.com.cy>
* GPIO release fix
* DC01 updates and I2C avr speed overwrite
- General updating of DC01
- Made F_SCL define in AVR I2C driver overwritable from config.h
* Update drivers/avr/i2c_master.c
* Initial commit of RAMA U80-A
* Initial commit of RAMA U80-A
* Moved IS31FL3736 driver, minor cleanups
* Superficial stuff
* Review changes
* Refactored to use common code.
* rgb_matrix: use a driver ops struct
This is intended to avoid #ifdef proliferation on adding more drivers,
eg. model01, which use different architectures.
* rgb_matrix: document driver struct members
* rgb_matrix: remove unused LED testing code
* rgb_matrix: don't build into IS31x drivers unless being used
* rgb_matrix: refactor make config options
This ensures that the necessary files are included for any custom
RGB_MATRIX_ENABLE value, without having to add entries here for specific
boards. This particularly affects model01 because its controller is
integrated and won't be used anywhere else, so it's preferable not to
put it in common_features.mk.
This now validates the value of RGB_MATRIX_ENABLE.
It was necessary to fix an error in ergodox_ez rules.mk using the wrong
comment separator, yielding an invalid value.
* IS31x drivers: don't write the control registers all the time
This is only needed when they are changed. This is done in init() and
board- or keymap-specific code is free to make further changes.
* rgb_matrix: move structs from chip drivers to rgb_matrix_drivers.c
This approach is specific to the rgb_matrix functionality, so keep it
neatly separated from the raw chip drivers.
* ISSI31FL3733 driver
- Addapted IS31 driver for the above driver
* fix my branch
* ISSI31FL3733 driver
- Inclusion of above ISSI led driver
* IS31fl3733 driver
- Added correct function for control registers
* Finalized support for ISSI31fl3733 led driver
- Finalized and tested driver.
- Modified i2c_master for arm due to declaration mistake.
- Fixed spaces/tabs in quantum.h file.
- Fixed spaces/tabs in common_features.mk file.
- Removed unnecessary includes from rgb_matrix.c file.
- Added local definitions for MIN and MAX macros in rgb_matrix.c file.
- Adjusted chevron effect.
- Added necessary define (RGB_3733_MATRIX_ENABLE) for makefile.
- Added necessary C define (ISSI3733) to aid with inclusion of the correct header file.
- Added documentation for the new driver.
* Driver structure update
- Changed rule includes to be more condensed (RGB_MATRIX_ENABLE = IS31FL3731) and (RGB_MATRIX_ENABLE = IS31FL3733)
- Updated documentation
- Reverted to the use of differently named functions for each driver and selecting the needed ones within rgb_matrix.c
* ISSI Drivers refractoring
- Moved issi drivers in a dedicated folder
- Updated documentation
* I2C library fix
I released the special pins incorrectly before. It is now fixed.
* Addition of I2C master driver for STM32, Generalization of ISSI3731 driver
- Addition of an i2c_master driver for STM32 to replicate expectations of AVR driver.
- Moved ISSI3731 driver one level up to make it accesible by both architectures.
- Renamed ISSI3731 functions to a more general name for preparation of other ISSI drivers.
- Added compiler directives where necessary to differenciate each architecture.
* converted tabs to spaces
* DC01 initial commit
- Addition of directories
- Left readme
* Initial commit of left half
* Initial files for right half
* arrow
* i2c adjustments
* I2C slave and DC01 refractoring
- Cleaned up state machine of I2C slave driver
- Modified DC01 left to use already pressent I2C master driver
- Modified DC01 matrixes
* Fixed tabs to spaces
* Addition of Numpad
* Add keymaps
- Orthopad keymap for numpad module
- Numpad keymap for numpad module
- ISO, ANSI and HHKB version of keymap for right module
* Minor matrix.c fixes
* Update Readmes
