Create central board for bluepill

This commit is contained in:
zvecr 2019-12-24 00:10:50 +00:00
parent e4a0f841e1
commit d3abebb601
3 changed files with 227 additions and 0 deletions

View file

@ -0,0 +1,56 @@
/*
ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio
Licensed under the Apache License, Version 2.0 (the "License");
you may not use this file except in compliance with the License.
You may obtain a copy of the License at
http://www.apache.org/licenses/LICENSE-2.0
Unless required by applicable law or agreed to in writing, software
distributed under the License is distributed on an "AS IS" BASIS,
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
See the License for the specific language governing permissions and
limitations under the License.
*/
#include "hal.h"
// Value to place in RTC backup register 10 for persistent bootloader mode
#define RTC_BOOTLOADER_FLAG 0x424C
/**
* @brief PAL setup.
* @details Digital I/O ports static configuration as defined in @p board.h.
* This variable is used by the HAL when initializing the PAL driver.
*/
#if HAL_USE_PAL || defined(__DOXYGEN__)
const PALConfig pal_default_config =
{
{VAL_GPIOAODR, VAL_GPIOACRL, VAL_GPIOACRH},
{VAL_GPIOBODR, VAL_GPIOBCRL, VAL_GPIOBCRH},
{VAL_GPIOCODR, VAL_GPIOCCRL, VAL_GPIOCCRH},
{VAL_GPIODODR, VAL_GPIODCRL, VAL_GPIODCRH},
{VAL_GPIOEODR, VAL_GPIOECRL, VAL_GPIOECRH},
};
#endif
/*
* Early initialization code.
* This initialization must be performed just after stack setup and before
* any other initialization.
*/
void __early_init(void) {
stm32_clock_init();
}
/*
* Board-specific initialization code.
*/
void boardInit(void) {
//JTAG-DP Disabled and SW-DP Enabled
AFIO->MAPR |= AFIO_MAPR_SWJ_CFG_JTAGDISABLE;
//Set backup register DR10 to enter bootloader on reset
BKP->DR10 = RTC_BOOTLOADER_FLAG;
}

View file

@ -0,0 +1,166 @@
/*
ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio
Licensed under the Apache License, Version 2.0 (the "License");
you may not use this file except in compliance with the License.
You may obtain a copy of the License at
http://www.apache.org/licenses/LICENSE-2.0
Unless required by applicable law or agreed to in writing, software
distributed under the License is distributed on an "AS IS" BASIS,
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
See the License for the specific language governing permissions and
limitations under the License.
*/
#ifndef _BOARD_H_
#define _BOARD_H_
/*
* Setup for a Generic STM32F103 board.
*/
/*
* Board identifier.
*/
#define BOARD_STM32_F103_STM32DUINO
#define BOARD_NAME "GENERIC STM32F103C8T6 board - stm32duino bootloader"
/*
* Board frequencies.
*/
#define STM32_LSECLK 32768
#define STM32_HSECLK 8000000
/*
* MCU type, supported types are defined in ./os/hal/platforms/hal_lld.h.
*/
#define STM32F103xB
/*
* IO pins assignments
*/
/* on-board */
#define GPIOA_LED 8
#define GPIOD_OSC_IN 0
#define GPIOD_OSC_OUT 1
/* In case your board has a "USB enable" hardware
controlled by a pin, define it here. (It could be just
a 1.5k resistor connected to D+ line.)
*/
/*
#define GPIOB_USB_DISC 10
*/
/*
* I/O ports initial setup, this configuration is established soon after reset
* in the initialization code.
*
* The digits have the following meaning:
* 0 - Analog input.
* 1 - Push Pull output 10MHz.
* 2 - Push Pull output 2MHz.
* 3 - Push Pull output 50MHz.
* 4 - Digital input.
* 5 - Open Drain output 10MHz.
* 6 - Open Drain output 2MHz.
* 7 - Open Drain output 50MHz.
* 8 - Digital input with PullUp or PullDown resistor depending on ODR.
* 9 - Alternate Push Pull output 10MHz.
* A - Alternate Push Pull output 2MHz.
* B - Alternate Push Pull output 50MHz.
* C - Reserved.
* D - Alternate Open Drain output 10MHz.
* E - Alternate Open Drain output 2MHz.
* F - Alternate Open Drain output 50MHz.
* Please refer to the STM32 Reference Manual for details.
*/
/*
* Port A setup.
* Everything input with pull-up except:
* PA2 - Alternate output (USART2 TX).
* PA3 - Normal input (USART2 RX).
* PA9 - Alternate output (USART1 TX).
* PA10 - Normal input (USART1 RX).
*/
#define VAL_GPIOACRL 0x88884B88 /* PA7...PA0 */
#define VAL_GPIOACRH 0x888884B8 /* PA15...PA8 */
#define VAL_GPIOAODR 0xFFFFFFFF
/*
* Port B setup.
* Everything input with pull-up except:
* PB10 - Push Pull output (USB switch).
*/
#define VAL_GPIOBCRL 0x88888888 /* PB7...PB0 */
#define VAL_GPIOBCRH 0x88888388 /* PB15...PB8 */
#define VAL_GPIOBODR 0xFFFFFFFF
/*
* Port C setup.
* Everything input with pull-up except:
* PC13 - Push Pull output (LED).
*/
#define VAL_GPIOCCRL 0x88888888 /* PC7...PC0 */
#define VAL_GPIOCCRH 0x88388888 /* PC15...PC8 */
#define VAL_GPIOCODR 0xFFFFFFFF
/*
* Port D setup.
* Everything input with pull-up except:
* PD0 - Normal input (XTAL).
* PD1 - Normal input (XTAL).
*/
#define VAL_GPIODCRL 0x88888844 /* PD7...PD0 */
#define VAL_GPIODCRH 0x88888888 /* PD15...PD8 */
#define VAL_GPIODODR 0xFFFFFFFF
/*
* Port E setup.
* Everything input with pull-up except:
*/
#define VAL_GPIOECRL 0x88888888 /* PE7...PE0 */
#define VAL_GPIOECRH 0x88888888 /* PE15...PE8 */
#define VAL_GPIOEODR 0xFFFFFFFF
/*
* USB bus activation macro, required by the USB driver.
*/
/* The point is that most of the generic STM32F103* boards
have a 1.5k resistor connected on one end to the D+ line
and on the other end to some pin. Or even a slightly more
complicated "USB enable" circuit, controlled by a pin.
That should go here.
However on some boards (e.g. one that I have), there's no
such hardware. In which case it's better to not do anything.
*/
/*
#define usb_lld_connect_bus(usbp) palClearPad(GPIOB, GPIOB_USB_DISC)
*/
#define usb_lld_connect_bus(usbp) palSetPadMode(GPIOA, 12, PAL_MODE_INPUT);
/*
* USB bus de-activation macro, required by the USB driver.
*/
/*
#define usb_lld_disconnect_bus(usbp) palSetPad(GPIOB, GPIOB_USB_DISC)
*/
#define usb_lld_disconnect_bus(usbp) palSetPadMode(GPIOA, 12, PAL_MODE_OUTPUT_PUSHPULL); palClearPad(GPIOA, 12);
#if !defined(_FROM_ASM_)
#ifdef __cplusplus
extern "C" {
#endif
void boardInit(void);
#ifdef __cplusplus
}
#endif
#endif /* _FROM_ASM_ */
#endif /* _BOARD_H_ */

View file

@ -0,0 +1,5 @@
# List of all the board related files.
BOARDSRC = $(BOARD_PATH)/boards/STM32_F103_STM32DUINO/board.c
# Required include directories
BOARDINC = $(BOARD_PATH)/boards/STM32_F103_STM32DUINO