* Add Per Key functionality for AutoShift (#11536)
* LED Matrix: Reactive effect buffers & advanced indicators (#12588)
* [Keyboard] kint36: switch to sym_eager_pk debouncing (#12626)
* [Keyboard] kint2pp: reduce input latency by ≈10ms (#12625)
* LED Matrix: Split (#12633)
* [CI] Format code according to conventions (#12650)
* feat: infinite timeout for leader key (#6580)
* feat: implement leader_no_timeout logic
* docs(leader_key): infinite leader timeout docs
* Format code according to conventions (#12680)
* Update ADC driver for STM32F1xx, STM32F3xx, STM32F4xx (#12403)
* Fix default ADC_RESOLUTION for ADCv3 (and ADCv4)
Recent ChibiOS update removed ADC_CFGR1_RES_10BIT from the ADCv3 headers
(that macro should not have been there, because ADCv3 has CFGR instead of
CFGR1). Fix the default value for ADC_RESOLUTION to use ADC_CFGR_RES_10BITS
if it is defined (that name is used for ADCv3 and ADCv4).
* Update ADC docs to match the actually used resolution
ADC driver for ChibiOS actually uses the 10-bit resolution by default
(probably to match AVR); fix the documentation accordingly. Also add
both ADC_CFGR_RES_10BITS and ADC_CFGR1_RES_10BIT constants (these names
differ according to the ADC implementation in the particular MCU).
* Fix pinToMux() for B12 and B13 on STM32F3xx
Testing on STM32F303CCT6 revealed that the ADC mux values for B12 and
B13 pins were wrong.
* Add support for all possible analog pins on STM32F1xx
Added ADC mux values for pins A0...A7, B0, B1, C0...C5 on STM32F1xx
(they are the same at least for STM32F103x8 and larger F103 devices, and
also F102, F105, F107 families). Actually tested on STM32F103C8T6
(therefore pins C0...C5 were not tested).
Pins F6...F10, which are present on STM32F103x[C-G] in 144-pin packages,
cannot be supported at the moment, because those pins are connected only
to ADC3, but the ChibiOS ADC driver for STM32F1xx supports only ADC1.
* Add support for all possible analog pins on STM32F4xx
Added ADC mux values for pins A0...A7, B0, B1, C0...C5 and optionally
F3...F10 (if STM32_ADC_USE_ADC3 is enabled). These mux values are
apparently the same for all F4xx devices, except some smaller devices may
not have ADC3.
Actually tested on STM32F401CCU6, STM32F401CEU6, STM32F411CEU6 (using
various WeAct “Blackpill” boards); only pins A0...A7, B0, B1 were tested.
Pins F3...F10 are inside `#if STM32_ADC_USE_ADC3` because some devices
which don't have ADC3 also don't have the GPIOF port, therefore the code
which refers to Fx pins does not compile.
* Fix STM32F3xx ADC mux table in documentation
The ADC driver documentation had some errors in the mux table for STM32F3xx.
Fix this table to match the datasheet and the actual code (mux settings for
B12 and B13 were also tested on a real STM32F303CCT6 chip).
* Add STM32F1xx ADC pins to the documentation
* Add STM32F4xx ADC pins to the documentation
* Add initial support for tinyuf2 bootloader (when hosted on F411 blackpill) (#12600)
* Add support for jumping to tinyuf2 bootloader. Adds blackpill UF2 example.
* Update flashing.md
* Update chconf.h
* Update config.h
* Update halconf.h
* Update mcuconf.h
* eeprom driver: Refactor where eeprom driver initialisation (and EEPROM emulation initialisation) occurs to make it non-target-specific. (#12671)
* Add support for MCU = STM32F446 (#12619)
* Add support for MCU = STM32F446
* Update platforms/chibios/GENERIC_STM32_F446XE/configs/config.h
* Restore mcuconf.h to the one used by RT-STM32F446RE-NUCLEO64
* stm32f446: update mcuconf.h and board.h for 16MHz operation, with USB enabled, and other peripherals disabled.
* Format code according to conventions (#12682)
* Format code according to conventions (#12687)
* Add STM32L433 and L443 support (#12063)
* initial L433 commit
* change to XC
* fix L433
* disable all peripherals
* update system and peripheral clocks
* 433 change
* use its own board files
* revert its own board files
* l433 specific change
* fix stm32l432xx define
* remove duplicate #define
* fix bootloader jump
* move to L443xx and add i2c2, spi2, usart3 to mcuconf.h
* move to L443
* move to L443
* fix sdmmc in mcuconf.h
* include STM32L443
* add L443
* Include L443 in compatible microcontrollers
* Include L443 in compatible microcontrollers
* Update config bootloader jump description
* Update ChibiOS define reasoning
* Update quantum/mcu_selection.mk
* fix git conflict
* Updated Function96 with V2 files and removed chconf.h and halconf.h (#12613)
* Fix bad PR merge for #6580. (#12721)
* Change RGB/LED Matrix to use a simple define for USB suspend (#12697)
* [CI] Format code according to conventions (#12731)
* Fixing transport's led/rgb matrix suspend state logic (#12770)
* [CI] Format code according to conventions (#12772)
* Fix comment parsing (#12750)
* Added OLED fade out support (#12086)
* fix some references to bin/qmk that slipped in (#12832)
* Resolve a number of warnings in `qmk generate-api` (#12833)
* New command: qmk console (#12828)
* stash poc
* stash
* tidy up implementation
* Tidy up slightly for review
* Tidy up slightly for review
* Bodge environment to make tests pass
* Refactor away from asyncio due to windows issues
* Filter devices
* align vid/pid printing
* Add hidapi to the installers
* start preparing for multiple hid_listeners
* udev rules for hid_listen
* refactor to move closer to end state
* very basic implementation of the threaded model
* refactor how vid/pid/index are supplied and parsed
* windows improvements
* read the report directly when usage page isn't available
* add per-device colors, the choice to show names or numbers, and refactor
* add timestamps
* Add support for showing bootloaders
* tweak the color for bootloaders
* Align bootloader disconnect with connect color
* add support for showing all bootloaders
* fix the pyusb check
* tweaks
* fix exception
* hide a stack trace behind -v
* add --no-bootloaders option
* add documentation for qmk console
* Apply suggestions from code review
* pyformat
* clean up and flesh out KNOWN_BOOTLOADERS
* Remove pointless SERIAL_LINK_ENABLE rules (#12846)
* Make Swap Hands use PROGMEM (#12284)
This converts the array that the Swap Hands feature uses to use PROGMEM,
and to read from that array, as such. Since this array never changes at
runtime, there is no reason to keep it in memory. Especially for AVR
boards, as memory is a precious resource.
* Fix another bin/qmk reference (#12856)
* [Keymap] Turn OLED off on suspend in soundmonster keymap (#10419)
* Fixup build errors on `develop` branch. (#12723)
* LED Matrix: Effects! (#12651)
* Fix syntax error when compiling for ARM (#12866)
* Remove KEYMAP and LAYOUT_kc (#12160)
* alias KEYMAP to LAYOUT
* remove KEYMAP and LAYOUT_kc
* Add setup, clone, and env to the list of commands we allow even with broken modules (#12868)
* Rename `point_t` -> `led_point_t` (#12864)
* [Keyboard] updated a vendor name / fixed minor keymap issues (#12881)
* Add missing LED Matrix suspend code to suspend.c (#12878)
* LED Matrix: Documentation (#12685)
* Deprecate `send_unicode_hex_string()` (#12602)
* Fix spelling mistake regarding LED Matrix in split_common. (#12888)
* [Keymap] Fix QWERTY/DVORAK status output for kzar keymap (#12895)
* Use milc.subcommand.config instead of qmk.cli.config (#12915)
* Use milc.subcommand.config instead
* pyformat
* remove the config test
* Add function to allow repeated blinking of one layer (#12237)
* Implement function rgblight_blink_layer_repeat to allow repeated blinking of one layer at a time
* Update doc
* Rework rgblight blinking according to requested change
* optimize storage
* Fixup housekeeping from being invoked twice per loop. (#12933)
* matrix: wait for row signal to go HIGH for every row (#12945)
I noticed this discrepancy (last row of the matrix treated differently than the
others) when optimizing the input latency of my keyboard controller, see also
https://michael.stapelberg.ch/posts/2021-05-08-keyboard-input-latency-qmk-kinesis/
Before this commit, when tuning the delays I noticed ghost key presses when
pressing the F2 key, which is on the last row of the keyboard matrix: the
dead_grave key, which is on the first row of the keyboard matrix, would be
incorrectly detected as pressed.
After this commit, all keyboard matrix rows are interpreted correctly.
I suspect that my setup is more susceptible to this nuance than others because I
use GPIO_INPUT_PIN_DELAY=0 and hence don’t have another delay that might mask
the problem.
* ensure we do not conflict with existing keymap aliases (#12976)
* Add support for up to 4 IS31FL3733 drivers (#12342)
* Convert Encoder callbacks to be boolean functions (#12805)
* [Keyboard] Fix Terrazzo build failure (#12977)
* Do not hard set config in CPTC files (#11864)
* [Keyboard] Corne - Remove legacy revision support (#12226)
* [Keymap] Update to Drashna keymap and user code (based on develop) (#12936)
* Add Full-duplex serial driver for ARM boards (#9842)
* Document LED_MATRIX_FRAMEBUFFER_EFFECTS (#12987)
* Backlight: add defines for default level and breathing state (#12560)
* Add dire message about LUFA mass storage bootloader (#13014)
* [Keyboard] Remove redundant legacy and common headers for crkbd (#13023)
Was causing compiler errors on some systems.
* Fix keyboards/keymaps for boolean encoder callback changes (#12985)
* `backlight.c`: include `eeprom.h` (#13024)
* Add changelog for 2021-05-29 Breaking Changes merge (#12939)
* Add ChangeLog for 2021-05-29 Breaking Changes Merge: initial version
* Add recent develop changes
* Sort recent develop changes
* Remove sections for ChibiOS changes per tzarc
No ChibiOS changes this round.
* Add and sort recent develop changes
* add notes about keyboard moves/deletions
* import changelog for PR 12172
Documents the change to BOOTMAGIC_ENABLE.
* update section headings
* re-sort changelog
* add additional note regarding Bootmagic changes
* remove changelog timestamp
* update dates in main Breaking Changes docs
* fix broken section anchors in previous changelogs
* add link to backlight/eeprom patch to changelog
* highlight some more changes
* link PRs from section headers
* Restore standard readme
* run: qmk cformat --core-only
* Branch point for 2020 November 28 Breaking Change
* Remove matrix_col_t to allow MATRIX_ROWS > 32 (#10183)
* Add support for soft serial to ATmega32U2 (#10204)
* Change MIDI velocity implementation to allow direct control of velocity value (#9940)
* Add ability to build a subset of all keyboards based on platform.
* Actually use eeprom_driver_init().
* Make bootloader_jump weak for ChibiOS. (#10417)
* Joystick 16-bit support (#10439)
* Per-encoder resolutions (#10259)
* Share button state from mousekey to pointing_device (#10179)
* Add hotfix for chibios keyboards not wake (#10088)
* Add advanced/efficient RGB Matrix Indicators (#8564)
* Naming change.
* Support for STM32 GPIOF,G,H,I,J,K (#10206)
* Add milc as a dependency and remove the installed milc (#10563)
* ChibiOS upgrade: early init conversions (#10214)
* ChibiOS upgrade: configuration file migrator (#9952)
* Haptic and solenoid cleanup (#9700)
* XD75 cleanup (#10524)
* OLED display update interval support (#10388)
* Add definition based on currently-selected serial driver. (#10716)
* New feature: Retro Tapping per key (#10622)
* Allow for modification of output RGB values when using rgblight/rgb_matrix. (#10638)
* Add housekeeping task callbacks so that keyboards/keymaps are capable of executing code for each main loop iteration. (#10530)
* Rescale both ChibiOS and AVR backlighting.
* Reduce Helix keyboard build variation (#8669)
* Minor change to behavior allowing display updates to continue between task ticks (#10750)
* Some GPIO manipulations in matrix.c change to atomic. (#10491)
* qmk cformat (#10767)
* [Keyboard] Update the Speedo firmware for v3.0 (#10657)
* Maartenwut/Maarten namechange to evyd13/Evy (#10274)
* [quantum] combine repeated lines of code (#10837)
* Add step sequencer feature (#9703)
* aeboards/ext65 refactor (#10820)
* Refactor xelus/dawn60 for Rev2 later (#10584)
* add DEBUG_MATRIX_SCAN_RATE_ENABLE to common_features.mk (#10824)
* [Core] Added `add_oneshot_mods` & `del_oneshot_mods` (#10549)
* update chibios os usb for the otg driver (#8893)
* Remove HD44780 References, Part 4 (#10735)
* [Keyboard] Add Valor FRL TKL (+refactor) (#10512)
* Fix cursor position bug in oled_write_raw functions (#10800)
* Fixup version.h writing when using SKIP_VERSION=yes (#10972)
* Allow for certain code in the codebase assuming length of string. (#10974)
* Add AT90USB support for serial.c (#10706)
* Auto shift: support repeats and early registration (#9826)
* Rename ledmatrix.h to match .c file (#7949)
* Split RGB_MATRIX_ENABLE into _ENABLE and _DRIVER (#10231)
* Split LED_MATRIX_ENABLE into _ENABLE and _DRIVER (#10840)
* Merge point for 2020 Nov 28 Breaking Change
* Re-fix the dual-bank bootloader stuff.
* Use wait_ms() instead of using nop's for a delay, as ChibiOS is actually running at the time of bootloader jump.
* I2C_TIMEOUT is not defined on arm teensy
* Work round teensy having different ChibiOS config options
* Stash OLED conf files
* update comment
* update comment
* Remove stm32 alias to allow teensy alt mode
* Branch point for 2020 May 30 Breaking Change
* Migrate `ACTION_LAYER_TOGGLE` to `TG()` (#8954)
* Migrate `ACTION_MODS_ONESHOT` to `OSM()` (#8957)
* Migrate `ACTION_DEFAULT_LAYER_SET` to `DF()` (#8958)
* Migrate `ACTION_LAYER_MODS` to `LM()` (#8959)
* Migrate `ACTION_MODS_TAP_KEY` to `MT()` (#8968)
* Convert V-USB usbdrv to a submodule (#8321)
* Unify Tap Hold functions and documentation (#8348)
* Changing board names to prevent confusion (#8412)
* Move the Keyboardio Model01 to a keyboardio/ subdir (#8499)
* Move spaceman keyboards (#8830)
* Migrate miscellaneous `fn_actions` entries (#8977)
* Migrate `ACTION_MODS_KEY` to chained mod keycodes (#8979)
* Organizing my keyboards (plaid, tartan, ergoinu) (#8537)
* Refactor Lily58 to use split_common (#6260)
* Refactor zinc to use split_common (#7114)
* Add a message if bin/qmk doesn't work (#9000)
* Fix conflicting types for 'tfp_printf' (#8269)
* Fixed RGB_DISABLE_AFTER_TIMEOUT to be seconds based & small internals cleanup (#6480)
* Refactor and updates to TKC1800 code (#8472)
* Switch to qmk forks for everything (#9019)
* audio refactor: replace deprecated PLAY_NOTE_ARRAY (#8484)
* Audio enable corrections (2/3) (#8903)
* Split HHKB to ANSI and JP layouts and Add VIA support for each (#8582)
* Audio enable corrections (Part 4) (#8974)
* Fix typo from PR7114 (#9171)
* Augment future branch Changelogs (#8978)
* Revert "Branch point for 2020 May 30 Breaking Change"
* Refactor to use mpaland/printf
* trim firmware size
* remove keymap changes
* run clang format
* Fixup after rebase
* fix up git-submodule command for printf
* Moved contents of rgblight_reconfig.h to rgblight_post_config.h.
In #3582, rgblight_reconfig.h had to be newly created. Now, the build system of qmk_firmware has a post_cofig feature, so that what was done in rgblight_reconfig.h can now be realized in rgblight_post_config.h.
**This commit does not change the build result.**
Testing script
```shell
# build on master
git checkout master
echo master > /tmp/master_md5.txt
# RGBLIGHT_ENABLE = no
make HELIX=verbose helix/rev2:default:clean
make HELIX=verbose helix/rev2:default
md5 helix_rev2_default.hex >> /tmp/master_md5.txt
# RGBLIGHT_ENABLE = yes, with animations
make HELIX=verbose helix/rev2/back:default:clean
make HELIX=verbose helix/rev2/back:default
md5 helix_rev2_back_default.hex >> /tmp/master_md5.txt
# RGBLIGHT_ENABLE = yes, without animations
make HELIX=verbose,no_ani helix/rev2/back:default:clean
make HELIX=verbose,no_ani helix/rev2/back:default
md5 helix_rev2_back_default.hex >> /tmp/master_md5.txt
# build on refactor_rgblight_reconfig.h
git checkout refactor_rgblight_reconfig.h
echo refactor_rgblight_reconfig.h > /tmp/branch_md5.txt
# RGBLIGHT_ENABLE = no
make HELIX=verbose helix/rev2:default:clean
make HELIX=verbose helix/rev2:default
md5 helix_rev2_default.hex >> /tmp/branch_md5.txt
# RGBLIGHT_ENABLE = yes, with animations
make HELIX=verbose helix/rev2/back:default:clean
make HELIX=verbose helix/rev2/back:default
md5 helix_rev2_back_default.hex >> /tmp/branch_md5.txt
# RGBLIGHT_ENABLE = yes, without animations
make HELIX=verbose,no_ani helix/rev2/back:default:clean
make HELIX=verbose,no_ani helix/rev2/back:default
md5 helix_rev2_back_default.hex >> /tmp/branch_md5.txt
diff -u /tmp/master_md5.txt /tmp/branch_md5.txt
```
Test result:
```
--- /tmp/master_md5.txt 2020-01-03 15:42:22.000000000 +0900
+++ /tmp/branch_md5.txt 2020-01-03 15:42:42.000000000 +0900
@@ -1,4 +1,4 @@
-master
+refactor_rgblight_reconfig.h
MD5 (helix_rev2_default.hex) = f360032edd522448366d471d8f4f8181
MD5 (helix_rev2_back_default.hex) = 0c663acc6cccc44476b3b969ad22a48f
MD5 (helix_rev2_back_default.hex) = e66b1195ff6d38e6e22c975b8ae42fd3
```
* Expressions that are too long are difficult to read, so wrap them.
* Edit the expression again
* remove `defined(RGBLIGHT_ANIMATIONS)` in `tmk_core/common/*/suspend.c`, `tmk_core/protocol/*/main.c`
move contents of rgblight_reconfig.h to rgblight.h.
The following changes were made to rgblight.h.
```diff
+#ifdef RGBLIGHT_USE_TIMER
void rgblight_task(void);
void rgblight_timer_init(void);
void rgblight_timer_enable(void);
void rgblight_timer_disable(void);
void rgblight_timer_toggle(void);
+#else
+#define rgblight_task()
+#define rgblight_timer_init()
+#define rgblight_timer_enable()
+#define rgblight_timer_disable()
+#define rgblight_timer_toggle()
+#endif
```
The following changes were made to tmk_core/common/avr/suspend.c, tmk_core/common/chibios/suspend.c, tmk_core/protocol/chibios/main.c, tmk_core/protocol/lufa/lufa.c, tmk_core/protocol/vusb/main.c.
```diff
-# ifdef RGBLIGHT_ANIMATIONS
rgblight_timer_enable();
-# endif
```
```diff
-#if defined(RGBLIGHT_ANIMATIONS) && defined(RGBLIGHT_ENABLE)
+#if defined(RGBLIGHT_ENABLE)
rgblight_task();
#endif
```
* remove 'defined(RGBLIGHT_ANIMATIONS)' in tmk_core/common/keyboard.c
Co-authored-by: Joel Challis <git@zvecr.com>
- uprintf -> dprintf
- Fix atsam "vendor" eeprom.
- Bump Kinetis K20x to 64 bytes, too.
- Rollback Kinetis to 32 bytes as partitioning can only be done once. Add warning about changing the value.
- Change RAM-backed "fake" EEPROM implementations to match eeconfig's current usage.
- Add 24LC128 by request.
* Add central location for chibios defines
* Add central location for chibios defines - actually add files this time....
* Add Copyright header
* Update include order to resolve i2cv1 build errors
* Move tmk_core/common/backlight to quantum/backlight
* Add guards to backlight inclusion
* Add guards to backlight inclusion
* Update backlight guards on clueboard/60
* Use full paths to avoid vpath issues
* Add stm32f072 base ck4x4 to handwired
* add prints
* Save these tries
* Save changes again
* Working hadron oled
* OLEd working but ws2812b still iffy:
* save another try
* Encoder feature + OLED
* RTC code
* Implement clock setting mode
* Whitespace
* Encoder hooked up to working LED PWM code
* Add missing files
* eeprom changes
* Save changes
* Move i2c master
* Move satisfaction75 under cannonkeys
* Set proper default folder
* Revert some core changes
* Undo paved iris changes
* Reorganize code for maintainability and prep for new features
* Add starting code for clock OLED mode
* Clock set mode finished
* Add custom encoder modes
* Actually add VIA keymap
* Gate to only 072
* fix gate for only 072
* Update header guards and includes
* Update i2c selection strategy
* Update board.c to handle software reset to DFU
* Move boards to cannonkeys and share resources
* Share common files between cannonkey boards
* Fix ortho60 keymap
* update LED numbers
* Add RGB keys to Ortho60 and Ortho48
* Add Backlight control to default layout Ortho60 and 48
* Remove unnecessary ws2812.c SRC from rules.mk
* initial commit, this now mostly works
- RGB controls work
- Dynamic keymap still broken due to eeprom
- Via works
* STM32 eeprom update
- Update EEPROM emulation library to handle 8bit data like AVR.
- This library also allows for multiple page pairs resulting in greater EEPROM size flexibility
* hs60 changes
* HS60 hhkb added
* Update keyboards/hs60/v2/config.h
Co-Authored-By: yiancar <yiangosyiangou@cytanet.com.cy>
* STM32 EEPROM Emulation
- Added EEPROM emulation libaries from libmaple and Arduino_STM32. https://github.com/rogerclarkmelbourne/Arduino_STM32 and https://github.com/leaflabs/libmaple.
- Renamed teensy EEPROM library and added conditional selection of library.
- Remapped EEPROM memory map for 16 byte blocks (as is with STM32f3xx MCUs).
- Added EEPROM initialization in main.c of Chibios.
- Added EEPROM format to clear the emulated pages when EEPROM is marked as invalid.
* Fixed ifdef
* Add suspend functions
* Disable RGB code if it's disabled
* Add suspend code to ChibiOS for future compatibility
* Add keyboard_init functions
* Change where references so it will compile
* Wrong command chained in wake up kb function
* Fix non-feature file changes
* Add documentation
* Re-add matrix init docs
* add rgblight code to example
* Remove keyboard init stuff for separate PR
