Static x & y should be the same type as touchData.xValue &
touchData.yValue: uint16_t.
Their delta could be larger than int8_t and should be constrained to
mouse_xy_report_t.
Move Pointing Device Initialization to after Split Post Initialization
If both pointing device and split is enabled, the pointing device init needs to be called after the split post init, otherwise the connection (serial/etc) isn't initialized yet, and any commands that need to send data over (such as calling the set cpi command) never get sent over.
* PMW33XX drivers overhaul
This combines the PMW3389 and PM3360 drivers as they only differ in the
firmware blobs and CPI get and set functions. The following changes have
been made:
* PMW3389 now gets the same multi-sensor feature that is already available on the
PMW3360.
* Introduced a shared pmw33xx_report_t struct is now directly readable via SPI
transactions instead of individual byte-sized reads, saving multiple
copies and bitshift operations.
* pmw33(89/60)_get_report functions had unreachable branches in their motion
detection logic these have been simplied as much as possible.
* The fast firmware upload option has been removed as this becomes obsolete by
the newly introduced polled waiting functions for ChibiOS polled waiting
* PMW33(60/89)_SPI_LSBFIRST and PMW33(60/89)_SPI_MODE config options
have been removed as they don't need to be configurable.
* All PMW3389 and PMW3360 defines have been unified to a PMW33XX prefix
to reduce code duplication and make the defines interchangeable
* Adjust keyboards to PMW33XX naming scheme
* Add missing '(' to print_bin_reverse32 declaration
* Fix insufficient character buffers on satisfaction75
* Remove \0 character in format string and use corrected offset math
instead on rocketboard 16
* Replace snprintf_ with snprintf for djinn
* Explicitly ignore format checks for tracktyl manuform that uses %b
specifier
* Print properly escaped version string in command.c, as PRODUCT or
other defines can contain constructs like 'Vendor keyboard 66%' which
will be interpreted as a format specifier
mpaland printf implementation was abandoned in ~2019 and the fork by
eyalroz is now regarded to be the goto replacement of it. So this commit
incoporates the changes needed to use this fork in QMK.
Note that pointer ptrdiff_t is always supported since commit
51c90f93a97fdaef895783ecbe24569be0db7cb8
* Disable RESET keycode because of naming conflicts
* Add Pico SDK as submodule
* Add RP2040 build support to QMK
* Adjust USB endpoint structs for RP2040
* Add RP2040 bootloader and double-tap reset routine
* Add generic and pro micro RP2040 boards
* Add RP2040 onekey keyboard
* Add WS2812 PIO DMA enabled driver and documentation
Supports regular and open-drain output configuration. RP2040 GPIOs are
sadly not 5V tolerant, so this is a bit use-less or needs extra hardware
or you take the risk to fry your hardware.
* Adjust SIO Driver for RP2040
* Adjust I2C Driver for RP2040
* Adjust SPI Driver for RP2040
* Add PIO serial driver and documentation
* Add general RP2040 documentation
* Apply suggestions from code review
Co-authored-by: Nick Brassel <nick@tzarc.org>
Co-authored-by: Nick Brassel <nick@tzarc.org>
* Initial import of wear-leveling algorithm.
* Alignment.
* Docs tweaks.
* Lock/unlock.
* Update quantum/wear_leveling/wear_leveling_internal.h
Co-authored-by: Stefan Kerkmann <karlk90@pm.me>
* More tests, fix issue with consolidation when unlocked.
* More tests.
* Review comments.
* Add plumbing for FNV1a.
* Another test checking that checksum mismatch clears the cache.
* Check that the write log still gets played back.
Co-authored-by: Stefan Kerkmann <karlk90@pm.me>
* Refactor steno into STENO_ENABLE_[ALL|GEMINI|BOLT]
* Update stenography documentation
* STENO_ENABLE_TXBOLT → STENO_ENABLE_BOLT
TXBOLT is a better name but BOLT is more consistent with the
pre-existing TX Bolt related constants, which all drop the "TX " prefix
* Comments
* STENO_ENABLE_[GEMINI|BOLT|ALL] → STENO_PROTOCOL = [geminipr|txbolt|all]
* Add note on lacking V-USB support
* Clear chord at the end of the switch(mode){send_steno_chord} block
* Return true if NOEVENT
* update_chord_xxx → add_xxx_key_to_chord
* Enable the defines for all the protocols if STENO_PROTOCOL = all
* Mention how to use `steno_set_mode`
* Set the default steno protocol to "all"
This is done so that existing keymaps invoking `steno_set_mode` don't
all suddenly break
* Add data driver equivalents for stenography feature
* Document format of serial steno packets
(Thanks dnaq)
* Add missing comma
