When address translation of insn fetch fails raise exception immediatly.
Use address_word as type of all address variables (instead of unsigned64),
the former is configured as either 32 or 64 bit type.
Always compile fpu code (no #if has fpu)
Add file sim-hload.c - generic load for hardware only simulators.
Review each simulators sim_open, sim_load, sim_create_inferior so that
they more closely match required behavour.
that image properties such as endianness can be checked.
More strongly document the expected behavour of each of the sim_*
interfaces.
Add default endian argument to simulator config macro
SIM_AC_OPTION_ENDIAN. Use in sim_config.
* interp.c: #include bfd.h.
(target_byte_order): Delete.
(sim_kind, myname, big_endian_p): New static locals.
(sim_open): Set sim_kind, myname. Move call to set_endianness to
after argument parsing. Recognize -E arg, set endianness accordingly.
(sim_load): Return SIM_RC. New arg abfd. Call sim_load_file to
load file into simulator. Set PC from bfd.
(sim_create_inferior): Return SIM_RC. Delete arg start_address.
(set_endianness): Use big_endian_p instead of target_byte_order.
(SignalException): Pass floating point cases to mips16_entry.
(ValueFPR): Don't restrict fmt_single and fmt_word to even
registers.
(StoreFPR): Likewise. Also, don't clobber fpr + 1 for fmt_single
or fmt_word.
(COP_LW): Pass fmt_word rather than fmt_uninterpreted to StoreFPR,
and then set the state to fmt_uninterpreted.
(COP_SW): Temporarily set the state to fmt_word while calling
ValueFPR.
(mips16_entry): New static function.
(SignalException): Look for mips16 entry and exit instructions.
(simulate): Use the correct index when setting fpr_state after
doing a pending move.
relative operands.
(build_instruction): Call JALDELAYSLOT rather than DELAYSLOT for a
jal instruction.
* interp.c (simJALDELAYSLOT): Define.
(JALDELAYSLOT): Define.
(INDELAYSLOT, INJALDELAYSLOT): Define.
(simulate): Clear simJALDELAYSLOT when simDELAYSLOT is cleared.
* gencode.c (build_instruction, case JUMP): Truncate PC to 32 bits.
* interp.c (CHECKHILO): Define away.
(simSIGINT): New macro.
(membank_size): Increase from 1MB to 2MB.
(control_c): New function.
(sim_resume): Rename parameter signal to signal_number. Add local
variable prev. Call signal before and after simulate.
(sim_stop_reason): Add simSIGINT support.
(sim_warning, sim_error, dotrace, SignalException): Define as stdarg
functions always.
(sim_warning): Delete call to SignalException. Do call printf_filtered
if logfh is NULL.
(AddressTranslation): Add #ifdef DEBUG around debugging message and
a call to sim_warning.
* interp.c (sim_monitor): Improved monitor printf
simulation. Tidied up simulator warnings, and added "--log" option
for directing warning message output.
* gencode.c: Use sim_warning() rather than WARNING macro.
AC_CHECK_LIB, and AC_CHECK_FUNCS. Change AC_OUTPUT to set
stamp-h.
* configure: Rebuild.
* config.in: New file, generated by autoheader.
* interp.c: Include "config.h". Include <stdlib.h>, <string.h>,
and <strings.h> if they exist. Replace #ifdef sun with #ifdef
HAVE_ANINT and HAVE_AINT, as appropriate.
* Makefile.in (run): Use @LIBS@ rather than -lm.
(interp.o): Depend upon config.h.
(Makefile): Just rebuild Makefile.
(clean): Remove stamp-h.
(mostlyclean): Make the same as clean, not as distclean.
(config.h, stamp-h): New targets.
* interp.c (xfer_direct_word, xfer_direct_long,
swap_direct_word, swap_direct_long, xfer_big_word,
xfer_big_long, xfer_little_word, xfer_little_long,
swap_word,swap_long): Added.
* interp.c (ColdReset): Provide function indirection to
host<->simulated_target transfer routines.
* interp.c (sim_store_register, sim_fetch_register): Updated to
make use of indirected transfer routines.
* interp.c (Convert): Provide round-to-nearest and round-to-zero
support for Sun hosts.
* Makefile.in (gencode): Ensure the host compiler and libraries
used for cross-hosted build.
Allow a DOS hosted version of the simulator to be built. NOTE: The FP
is still not complete, since round-to-nearest and round-to-zero have
not been implemented generically.
support.
* interp.c: Added dineroIII, and BSD profiling support. Also
run-time FP handling.
At the moment the options are still mostly build-time controlled,
rather than run-time. Also work still needs to be done to remove (long
long) usage (However this is trivial, just time-consuming).
The out-standing instruction work to be done is in supporting round
and trunc for FP operations, and providing better exception support.
