This commit converts a call to fatal in remote_prepare with a call to
error. remote_prepare is called precisely once, from main, at a point
where jumping to toplevel will call exit (1), so error and fatal are
functionally equivalent at this point. Note that remote_prepare calls
perror_with_name (which calls error) so callers of remote_prepare must
already handle the fact that it may exit via longjmp.
gdb/gdbserver/ChangeLog:
* remote-utils.c (remote_prepare): Replace fatal with error.
This commit downgrades a fatal error to a warning in linux_async.
linux_async is called from two different places in gdbserver:
Via target_async from handle_accept_event. The argument
is always zero, so the warning will never be printed here.
Via start_non_stop from handle_general_set. This prints
its own error message to stderr on failure, which will
be preceded by the warning if it is emitted.
gdb/gdbserver/ChangeLog:
* linux-low.c (linux_async): Replace fatal with warning.
Tidy up and return.
(linux_start_non_stop): Return -1 if linux_async failed.
This commit converts if..fatal checks in both i386_dr_low_set_addr
implementations to gdb_asserts. It's not obvious from the context,
but the conditional in both cases is changed to match the equivalent
conditional in the i386_dr_low_get_addr implementations. Nothing
fundamental has changed because DR_FIRSTADDR is zero. This commit
also removes a vague comment in Linux i386_dr_low_get_addr. I could
have reworded the comment (and replicated it three times for the other
identical assertions) but I think the existence of specific functions
for the status and control registers makes it fairly obvious what is
going on.
gdb/gdbserver/ChangeLog:
* linux-x86-low.c (i386_dr_low_set_addr): Replace check with
gdb_assert.
(i386_dr_low_get_addr): Remove vague comment.
* win32-i386-low.c (i386_dr_low_set_addr): Replace check with
gdb_assert.
GDB and SIM both have functions called "debug_printf", which conflicts
at link time. This commit shadows SIM's debug_printf with a macro so
that SIM's symbol ends up being called "sim_debug_printf".
sim/common/ChangeLog:
* sim-trace.h (debug_printf): New define.
Hi,
This patch is to handle a software watchpoint case that program returns
to caller's epilogue, and it causes the fail in thumb mode,
finish^M
Run till exit from #0 func () at gdb/testsuite/gdb.base/watchpoint-cond-gone.c:26^M
0x000001f6 in jumper ()^M
(gdb) FAIL: gdb.base/watchpoint-cond-gone.exp: Catch the no longer valid watchpoint
In the test, jumper calls func, and programs returns from func to
jumper's epilogue, IOW, the branch instruction is the last instruction
of jumper's function body.
jumper:
.....
0x000001f2 <+10>: bl 0x200 [1] <---- indirect call to func
0x000001f6 <+14>: mov sp, r7 [2] <---- start of the epilogue
0x000001f8 <+16>: add sp, #8
0x000001fa <+18>: pop {r7}
0x000001fc <+20>: pop {r0}
0x000001fe <+22>: bx r0
When the inferior returns from func back to jumper, it is expected
that an expression of a software watchpoint becomes out-of-scope.
GDB validates the expression by checking the corresponding frame,
but this check is guarded by gdbarch_in_function_epilogue_p. See
breakpoint.c:watchpoint_check.
It doesn't work in this case, because program returns from func's
epilogue back to jumper's epilogue [2], GDB thinks the program is
still within the epilogue, but in fact it goes to a different one.
When PC points at [2], the sp-restore instruction is to be
executed, so the stack frame isn't destroyed yet and we can still
use the frame mechanism reliably.
Note that when PC points to the first instruction of restoring SP,
it is part of epilogue, but we still return zero. When goes to
the next instruction, the backward scan will still match the
epilogue sequence correctly. The reason for doing this is to
handle the "return-to-epilogue" case.
What this patch does is to restrict the epilogue matching that let
GDB think the first SP restore instruction isn't part of the epilogue,
and fall back to use frame mechanism. We set 'found_stack_adjust'
zero before backward scan, and we've done this for arm mode
counterpart (arm_in_function_epilogue_p) too.
The patch is tested in arm-none-eabi and arm-none-linux-gnueabi with
various multilibs. OK to apply?
gdb:
2014-08-28 Yao Qi <yao@codesourcery.com>
* arm-tdep.c (thumb_in_function_epilogue_p): Don't set
found_stack_adjust in forward scan. Remove condition check
on found_stack_adjust which is always true. Indent the code.
Hi,
dwarf_decode_lines is called in two functions,
dwarf2_build_include_psymtabs and handle_DW_AT_stmt_list, in which, 1
is passed to argument 'want_line_info' and 'want_line_info' is a
conditional variable in dwarf_decode_lines. We can simplify it by
removing 'want_line_info' and propagating the constant 1 into
dwarf_decode_lines. This is what this patch does. This patch also
remove one line comment about WANT_LINE_INFO in
handle_DW_AT_stmt_list, as handle_DW_AT_stmt_list doesn't have such
argument.
gdb:
2014-08-28 Yao Qi <yao@codesourcery.com>
* dwarf2read.c (dwarf_decode_lines): Update declaration.
(handle_DW_AT_stmt_list): Remove comment about WANT_LINE_INFO.
(dwarf_decode_lines): Remove argument
want_line_info. Remove condition check on want_line_info.
Callers update.
The TUI terminal state becomes corrupted (e.g. key sequences such as
Alt_F and Alt_B no longer work) when one attaches to an inferior process
(via "run" or "attach") from within TUI. This terminal corruption
remains until you switch out of TUI mode.
This happens because the terminal state is not properly saved when
switching to and out from TUI mode. Although the functions tui_enable()
and tui_disable() both call the function target_terminal_save_ours() to
save the terminal state, this function is a no-op unless GDB has already
attached to an inferior process. This is because only the "native"
target has a useful implementation of target_terminal_save_ours()
(namely child_terminal_save_ours()) and we only have the "native" target
in our target vector if GDB has already attached to an inferior process.
So without an inferior process, switching to and from TUI mode does not
actually save the terminal state. Therefore when you attach to an
inferior process from within TUI mode, the proper terminal state is not
restored (after swapping from the inferior's terminal back to the GDB
terminal).
To fix this we just have to ensure that the terminal state is always
being properly saved when switching from and to TUI mode. To achieve
this, this patch removes the polymorphic function
target_terminal_save_ours() and replaces it with a regular function
gdb_save_tty_state() that always saves the terminal state.
Tested on x86_64-unknown-linux-gnu by running "make check", no new
regressions.
gdb/ChangeLog:
* target.h (struct target_ops::to_terminal_save_ours): Remove
declaration.
(target_terminal_save_ours): Remove macro.
* target-delegates.c: Regenerate.
* inf-child.c (inf_child_target): Don't set the nonexistent
field to_terminal_save_ours.
* inferior.h (child_terminal_save_ours): Remove declaration.
* terminal.h (gdb_save_tty_state): New declaration.
* inflow.c (child_terminal_save_ours): Rename to ...
(gdb_save_tty_state): ... this.
* tui/tui.c: Include terminal.h.
(tui_enable): Use gdb_save_tty_state instead of
target_terminal_save_ours.
(tui_disable): Likewise.
This began as an attempt to make a few small changes to src-release
but heeding the comments at the top of the file it seemed it might be
wise to convert it to a shell script instead which should hopefully
be more maintainable.
This shell script contains most of the functionality of the Makefile
version. It can be run like this:
# This will build gdb and compress with bzip2, gzip and xz
./src-release.sh -bgx gdb
The functionality that has been removed is building tarballs for insight
and gnats, which were broken in the current repository layout and
gas+binutils which amounted to basically the same thing as binutils so
didn't seem worth keeping. The script always builds a tar file,
compression is optional, so no need for specific commands to build tar
files rather than compressed tar files.
The build of gas releases has been fixed, as has extraction of version
numbers which had been broken since the switch to configure.ac files
and AC_INIT.
I also removed the code for distcleaning the intl sub-directory as it
seems like that issue has been fixed.
The script is capable of compressing with bzip2, gzip and xz which
should cover all formats available on gnu.org.
I tested it by producing release tarballs which are substantially
identical to the ones produced by the src-release script.
ChangeLog:
2014-08-27 Will Newton <will.newton@linaro.org>
* src-release.sh: New file.
* src-release: Remove file.
gas/
* config/tc-arm.c (aeabi_set_public_attributes): Update intended_arch based
on the info we got during parsing.
(arm_handle_align): Make sure the p2align expanding logic under thumb
unchanged.
gas/testsuite/
* gas/arm/blx-bl-convert.d: New testcase.
* gas/arm/blx-bl-convert.l: Warning expectation.
* gas/arm/blx-bl-convert.s: Source file.
2014-08-26 Jiong Wang <jiong.wang@arm.com>
bfd/
* elfnn-aarch64.c (elfNN_aarch64_check_relocs): Initialize non_got_ref
properly for MOVW_G0/1/2_NC and MOVW_G3. Reject them when linking
shared library.
(elfNN_aarch64_gc_sweep_hook): Add check on these relocs.
ld/testsuite/
* ld-aarch64/copy-relocs-so.s: New test file.
* ld-aarch64/copy-relocs-exe.s: Likewise.
* ld-aarch64/copy-relocs.d: New expectation file.
* ld-aarch64/emit-relocs-264-bad.d: New test file.
* ld-aarch64/emit-relocs-266-bad.d: Likewise.
* ld-aarch64/emit-relocs-268-bad.d: Likewise.
* ld-aarch64/emit-relocs-269-bad.d: Likewise.
* ld-aarch64/aarch64-elf.exp: Run new added test.
Resolves PR 17312
* ld-aarch64/eh-frame-foo.s: Use 8-byte offset for X30.
* ld-aarch64/eh-frame-bar.s: Likewise.
* ld-aarch64/eh-frame.d: Updated to match current readelf output.
* ld-elf/eh5.d: Allow any register names.
This change moves the microMIPS 10-bit uninterpreted immediate code
embedded at bits 25..16 in the SYSCALL, WAIT, SDBBP and HYPCALL
instructions from `B' over to `+J' which is the operand code used in
the standard MIPS instruction set for a similar code embedded at bits
20..11, currently used by HYPCALL only in that set.
opcodes/
* micromips-opc.c (decode_micromips_operand): Rename `B' to `+J'.
(micromips_opcodes): Use "+J" in place of "B" for "hypcall",
"sdbbp", "syscall" and "wait".
include/opcode/
* mips.h: Document the move of `MICROMIPSOP_*_CODE10' from `B'
over to `+J'.
This change removes code duplication for the SAA macro in line with other
such macros and also adds a !microMIPS internal consistency guard as
there's no microMIPS encoding of the underlying SAA/SAAD instructions.
* config/tc-mips.c (macro) <M_SAA_AB>: Remove duplicate code and
jump to...
<M_SAAD_AB>: ... here. Assert that !microMIPS.
I read comment of scan_partial_symbols about NEED_PC and how *LOWPC
and *HIGHPC are updated:
DW_AT_ranges). If NEED_PC is set, then this function will set
*LOWPC and *HIGHPC to the lowest and highest PC values found in CU
and record the covered ranges in the addrmap.
NEED_PC is only used in the callee of scan_partial_symbols,
add_partial_subprogram,
if (pdi->tag == DW_TAG_subprogram)
{
if (pdi->has_pc_info)
{
if (pdi->lowpc < *lowpc)
*lowpc = pdi->lowpc;
if (pdi->highpc > *highpc)
*highpc = pdi->highpc;
if (need_pc)
*LOWPC and *HIGHPC is updated regardless of NEED_PC. When NEED_PC is
true, addrmap is updated. It would be clear to rename NEED_PC to
SET_ADDRMAP. That is what this patch does. Beside this, this patch
also adjust comments in related functions.
gdb:
2014-08-24 Yao Qi <yao@codesourcery.com>
* dwarf2read.c (scan_partial_symbols): Update comments.
Rename argument 'need_pc' with 'set_addrmap'.
（add_partial_namespace): Rename argument 'need_pc' with
'set_addrmap'.
(add_partial_module): Likewise.
(add_partial_subprogram): Likewise. Update comments.
(dwarf2_name): Fix typo.
I see the following fails on arm-none-eabi target,
print sn^M
$14 = 0x0 <_ftext>^M
(gdb) FAIL: gdb.python/py-value.exp: print sn
print sn^M
$14 = 0x0 <_ftext>^M
(gdb) FAIL: gdb.guile/scm-value.exp: print sn
as <_ftext> is unexpected. This patch is to set print symbol off to
avoid printing this.
gdb/testsuite:
2014-08-24 Yao Qi <yao@codesourcery.com>
* gdb.guile/scm-value.exp (test_lazy_strings): Set print
symbol off.
* gdb.python/py-value.exp (test_lazy_strings): Likewise.
The situation here is similar to that of the other nearby (previous)
sims fixed; it fails at the dv_sockser_install declaration in
sim/m32r/tconfig.in. But, as opposed to e.g. frv, this *does* have a
definition of UART_INCHAR_ADDR et al. It's somewhat tempting to keep
sim-hardware enabled here but, I'm disabling it for the same reasons
as for frv. Unsurprisingly (as m32r seems to be the template), the
same confusing lines are in sim/m32r/Makefile.in as in
sim/frv/Makefile.in at that time, deleted in 73e76d20. Again, commit
73e76d20 (for m32r as well as for frv) attempted to move the
non-existing dv-sockser.o use to $(m32r_extra_objs) but missed that
AC_SUBST would only affect @m32r_extra_objs@ and not
$(m32r_extra_objs) per se so nothing happened. As for frv, I'm
removing the $(m32r_extra_objs) too, to avoid confusion. Make
check-sim for m32r-elf shows no regressions (5 failures; 100 expected
passes) compared to bf3d9781ec (before the recent config.in regen,
after sim-hardware mostly-enabled) and eed23bb4a1 (before the
sim-hardware mostly-enabled; 2013-03-23).
sim/m32r:
* configure.ac: Default simulator hardware to off again. Remove
dead m32r_extra_objs substitution.
* configure: Regenerate.
* Makefile.in: Remove unused frv_extra_objs.
See nearby (previous) commit for the iq2000 sim; this similarly fails
at the dv_sockser_install declaration in sim/sh64/tconfig.in. I'm
disabling simulator hardware to be consistent with the state before
94c63d78f (2013-03-23) and with the actions for the frv sim and the
iq2000 sim. Make check-sim for sh64-elf shows no regressions (25
failures; 357 expected passes) compared to bf3d9781ec (before the
recent config.in regen, after sim-hardware mostly-enabled) and
eed23bb4a1 (before the sim-hardware mostly-enabled; 2013-03-23).
sim/sh64:
* configure.ac: Default simulator hardware to off again
without emitting errors when off or dv-sockser.o unavailable.
* configure: Regenerate.
See nearby (previous) commit for the frv sim; this similarly fails at
the dv_sockser_install declaration in sim/iq2000/tconfig.in. There's
no HAVE_DV_SOCKSER conditionals here and no other dv-sockser.o
artefacts so maybe there is no further fallout, but I'm going to
disable sim-hardware just be consistent with the state before
94c63d78f (2013-03-23) and with the actions for the frv sim. Make
check-sim for iq2000-elf shows no failures but that's in no small part
because it has no test-suite.
sim/iq2000:
* configure.ac: Default simulator hardware to off again
without emitting errors when off or dv-sockser.o unavailable.
* configure: Regenerate.
At 2974be626, frv-elf fails at the dv_sockser_install declaration in
sim/frv/tconfig.in. But, with the trivial #include's added (see other
sims tconfig.in, like cris or mn10300), it *still* fails building
sim/frv/devices.c because of a missing UART_INCHAR_ADDR. I have no
insight into what'd be a valid value, except that there's a definition
in m32r, which was probably used as a template with frv not finished.
Simulated hardware should not have been be enabled, and was indeed not
enabled by default before 94c63d78f (2013-03-23), where it seems to
have been enabled for no simulator-specific reason. Except
dv-sockser.o wasn't enabled even then: sim/frv/config.in wasn't
regenerated, so HAVE_DV_SOCKSER was never defined. Maybe people were
fooled by this in sim/frv/Makefile.in at that time (these two lines
were later deleted, in 73e76d20):
CONFIG_DEVICES = dv-sockser.o
CONFIG_DEVICES =
(As it seems people have missed it before: the second line overrides
the first...) I'm guessing these lines were part of the
never-completed hardware-support. Commit 73e76d20 attempted to move
the imagined dv-sockser.o from $(CONFIG_DEVICES) to $(frv_extra_objs)
but missed that AC_SUBST would only affect @frv_extra_objs@ (not
$(frv_extra_objs) per se) so nothing happened regarding sockser:
dv-sockser.o was not compiled and HAVE_DV_SOCKSER was not defined.
I'm removing the $(frv_extra_objs) too, to avoid confusion. The best
action seems to be disabling all hardware support by default again
until a specific sim maintainer finishes the work.
Make check-sim for frv-elf shows no failures after this.
sim/frv:
* configure.ac: Default simulator hardware to off again. Remove
dead frv_extra_objs substitution.
* configure: Regenerate.
* Makefile.in: Remove unused frv_extra_objs.
See the description here:
https://sourceware.org/ml/gdb-patches/2014-08/msg00283.html
This patch keeps track of whether the current line has seen a
non-zero discriminator, and if so coalesces consecutive entries
for the same line (by ignoring all entries after the first).
gdb/ChangeLog:
PR 17276
* dwarf2read.c (dwarf_record_line_p): New function.
(dwarf_decode_lines_1): Ignore subsequent line number entries
for the same line if any entry had a non-zero discriminator.
gdb/testsuite/ChangeLog:
* gdb.dwarf2/dw2-single-line-discriminators.S: New file.
* gdb.dwarf2/dw2-single-line-discriminators.c: New file.
* gdb.dwarf2/dw2-single-line-discriminators.exp: New file.
gdb/ChangeLog:
* buildsym.h (record_line_ftype): New typedef.
(record_line): Use it.
* dwarf2read.c (dwarf_record_line, dwarf_finish_line): New functions.
(dwarf_decode_lines_1): Call them.
Only set the VLE flag if the instruction has been pulled via the VLE
instruction set. This way the flag is guaranteed to be set for VLE-only
instructions or for VLE-only processors, however it'll remain clear for
dual-mode instructions on dual-mode and, more importantly, standard-mode
processors.
gas/
* config/tc-ppc.c (md_assemble): Only set the PPC_APUINFO_VLE
flag if both the processor and opcode flags match.
ld/testsuite/
* ld-powerpc/apuinfo-vle.rd: New test.
* ld-powerpc/apuinfo-vle.s: New test source.
* ld-powerpc/apuinfo.rd: Adjust according to GAS PPC_APUINFO_VLE
handling change.
* ld-powerpc/powerpc.exp: Run the new test.
2014-08-21 Nathan Sidwell <nathan@codesourcery.com>
Maciej W. Rozycki <macro@codesourcery.com>
opcodes/
* arm-dis.c (print_arm_address): Negate the GPR-relative offset
returned if the U bit is set.
2014-08-21 Paul Brook <paul@codesourcery.com>
gas/testsuite/
* gas/arm/arch7a-mp.d: Adjust according to `print_arm_address'
offset fix.
* gas/arm/arch7r-mp.d: Likewise.
cc1: warnings being treated as errors
.../gas/config/tc-arm.c: In function 'add_to_lit_pool':
.../gas/config/tc-arm.c:3193: error: 'imm1' may be used uninitialized in this function
* config/tc-arm.c (add_to_lit_pool): Preinitialize `imm1'.
