mirrors/qmk_firmware
1
0
Fork 1
mirror of https://github.com/qmk/qmk_firmware synced 2024-11-18 09:55:48 +00:00
Code Issues Projects Releases Packages Wiki Activity
qmk_firmware/platforms/avr/bootloader.c
Joel Challis 2728603fe6
Move tmk_core/common/<plat> (#13918)
2021-11-19 10:41:02 -08:00

293 lines
9 KiB
C
Raw Blame History

#include <stdint.h>
#include <stdbool.h>
#include <avr/io.h>
#include <avr/eeprom.h>
#include <avr/interrupt.h>
#include <avr/wdt.h>
#include <util/delay.h>
#include "bootloader.h"
#include <avr/boot.h>
#ifdef PROTOCOL_LUFA
# include <LUFA/Drivers/USB/USB.h>
#endif
/** \brief Bootloader Size in *bytes*
*
* AVR Boot section size are defined by setting BOOTSZ fuse in fact. Consult with your MCU datasheet.
* Note that 'Word'(2 bytes) size and address are used in datasheet while TMK uses 'Byte'.
*
* Size of Bootloaders in bytes:
* Atmel DFU loader(ATmega32U4) 4096
* Atmel DFU loader(AT90USB128) 8192
* LUFA bootloader(ATmega32U4) 4096
* Arduino Caterina(ATmega32U4) 4096
* USBaspLoader(ATmega***) 2048
* Teensy halfKay(ATmega32U4) 512
* Teensy++ halfKay(AT90USB128) 1024
*
* AVR Boot section is located at the end of Flash memory like the followings.
*
* byte Atmel/LUFA(ATMega32u4) byte Atmel(AT90SUB128)
* 0x0000 +---------------+ 0x00000 +---------------+
* | | | |
* | | | |
* | Application | | Application |
* | | | |
* = = = =
* | | 32KB-4KB | | 128KB-8KB
* 0x7000 +---------------+ 0x1E000 +---------------+
* | Bootloader | 4KB | Bootloader | 8KB
* 0x7FFF +---------------+ 0x1FFFF +---------------+
*
*
* byte Teensy(ATMega32u4) byte Teensy++(AT90SUB128)
* 0x0000 +---------------+ 0x00000 +---------------+
* | | | |
* | | | |
* | Application | | Application |
* | | | |
* = = = =
* | | 32KB-512B | | 128KB-1KB
* 0x7E00 +---------------+ 0x1FC00 +---------------+
* | Bootloader | 512B | Bootloader | 1KB
* 0x7FFF +---------------+ 0x1FFFF +---------------+
*/
#define FLASH_SIZE (FLASHEND + 1L)
#if !defined(BOOTLOADER_SIZE)
uint16_t bootloader_start;
#endif
// compatibility between ATMega8 and ATMega88
#if !defined(MCUCSR)
# if defined(MCUSR)
# define MCUCSR MCUSR
# endif
#endif
/** \brief Entering the Bootloader via Software
*
* http://www.fourwalledcubicle.com/files/LUFA/Doc/120730/html/_page__software_bootloader_start.html
*/
#define BOOTLOADER_RESET_KEY 0xB007B007
uint32_t reset_key __attribute__((section(".noinit,\"aw\",@nobits;")));
/** \brief initialize MCU status by watchdog reset
*
* FIXME: needs doc
*/
__attribute__((weak)) void bootloader_jump(void) {
#if !defined(BOOTLOADER_SIZE)
uint8_t high_fuse = boot_lock_fuse_bits_get(GET_HIGH_FUSE_BITS);
if (high_fuse & ~(FUSE_BOOTSZ0 & FUSE_BOOTSZ1)) {
bootloader_start = (FLASH_SIZE - 512) >> 1;
} else if (high_fuse & ~(FUSE_BOOTSZ1)) {
bootloader_start = (FLASH_SIZE - 1024) >> 1;
} else if (high_fuse & ~(FUSE_BOOTSZ0)) {
bootloader_start = (FLASH_SIZE - 2048) >> 1;
} else {
bootloader_start = (FLASH_SIZE - 4096) >> 1;
}
#endif
// Something like this might work, but it compiled larger than the block above
// bootloader_start = FLASH_SIZE - (256 << (~high_fuse & 0b110 >> 1));
#if defined(BOOTLOADER_HALFKAY)
// http://www.pjrc.com/teensy/jump_to_bootloader.html
cli();
// disable watchdog, if enabled (it's not)
// disable all peripherals
// a shutdown call might make sense here
UDCON = 1;
USBCON = (1 << FRZCLK); // disable USB
UCSR1B = 0;
_delay_ms(5);
# if defined(__AVR_AT90USB162__) // Teensy 1.0
EIMSK = 0;
PCICR = 0;
SPCR = 0;
ACSR = 0;
EECR = 0;
TIMSK0 = 0;
TIMSK1 = 0;
UCSR1B = 0;
DDRB = 0;
DDRC = 0;
DDRD = 0;
PORTB = 0;
PORTC = 0;
PORTD = 0;
asm volatile("jmp 0x3E00");
# elif defined(__AVR_ATmega32U4__) // Teensy 2.0
EIMSK = 0;
PCICR = 0;
SPCR = 0;
ACSR = 0;
EECR = 0;
ADCSRA = 0;
TIMSK0 = 0;
TIMSK1 = 0;
TIMSK3 = 0;
TIMSK4 = 0;
UCSR1B = 0;
TWCR = 0;
DDRB = 0;
DDRC = 0;
DDRD = 0;
DDRE = 0;
DDRF = 0;
TWCR = 0;
PORTB = 0;
PORTC = 0;
PORTD = 0;
PORTE = 0;
PORTF = 0;
asm volatile("jmp 0x7E00");
# elif defined(__AVR_AT90USB646__) // Teensy++ 1.0
EIMSK = 0;
PCICR = 0;
SPCR = 0;
ACSR = 0;
EECR = 0;
ADCSRA = 0;
TIMSK0 = 0;
TIMSK1 = 0;
TIMSK2 = 0;
TIMSK3 = 0;
UCSR1B = 0;
TWCR = 0;
DDRA = 0;
DDRB = 0;
DDRC = 0;
DDRD = 0;
DDRE = 0;
DDRF = 0;
PORTA = 0;
PORTB = 0;
PORTC = 0;
PORTD = 0;
PORTE = 0;
PORTF = 0;
asm volatile("jmp 0xFC00");
# elif defined(__AVR_AT90USB1286__) // Teensy++ 2.0
EIMSK = 0;
PCICR = 0;
SPCR = 0;
ACSR = 0;
EECR = 0;
ADCSRA = 0;
TIMSK0 = 0;
TIMSK1 = 0;
TIMSK2 = 0;
TIMSK3 = 0;
UCSR1B = 0;
TWCR = 0;
DDRA = 0;
DDRB = 0;
DDRC = 0;
DDRD = 0;
DDRE = 0;
DDRF = 0;
PORTA = 0;
PORTB = 0;
PORTC = 0;
PORTD = 0;
PORTE = 0;
PORTF = 0;
asm volatile("jmp 0x1FC00");
# endif
#elif defined(BOOTLOADER_CATERINA)
// this block may be optional
// TODO: figure it out
uint16_t *const bootKeyPtr = (uint16_t *)0x0800;
// Value used by Caterina bootloader use to determine whether to run the
// sketch or the bootloader programmer.
uint16_t bootKey = 0x7777;
*bootKeyPtr = bootKey;
// setup watchdog timeout
wdt_enable(WDTO_60MS);
while (1) {
} // wait for watchdog timer to trigger
#elif defined(BOOTLOADER_USBASP)
// Taken with permission of Stephan Baerwolf from https://github.com/tinyusbboard/API/blob/master/apipage.c
wdt_enable(WDTO_15MS);
wdt_reset();
asm volatile("cli \n\t"
"ldi r29 , %[ramendhi] \n\t"
"ldi r28 , %[ramendlo] \n\t"
# if (FLASHEND > 131071)
"ldi r18 , %[bootaddrhi] \n\t"
"st Y+, r18 \n\t"
# endif
"ldi r18 , %[bootaddrme] \n\t"
"st Y+, r18 \n\t"
"ldi r18 , %[bootaddrlo] \n\t"
"st Y+, r18 \n\t"
"out %[mcucsrio], __zero_reg__ \n\t"
"bootloader_startup_loop%=: \n\t"
"rjmp bootloader_startup_loop%= \n\t"
:
: [mcucsrio] "I"(_SFR_IO_ADDR(MCUCSR)),
# if (FLASHEND > 131071)
[ramendhi] "M"(((RAMEND - 2) >> 8) & 0xff), [ramendlo] "M"(((RAMEND - 2) >> 0) & 0xff), [bootaddrhi] "M"((((FLASH_SIZE - BOOTLOADER_SIZE) >> 1) >> 16) & 0xff),
# else
[ramendhi] "M"(((RAMEND - 1) >> 8) & 0xff), [ramendlo] "M"(((RAMEND - 1) >> 0) & 0xff),
# endif
[bootaddrme] "M"((((FLASH_SIZE - BOOTLOADER_SIZE) >> 1) >> 8) & 0xff), [bootaddrlo] "M"((((FLASH_SIZE - BOOTLOADER_SIZE) >> 1) >> 0) & 0xff));
#else // Assume remaining boards are DFU, even if the flag isn't set
# if !(defined(__AVR_ATmega32A__) || defined(__AVR_ATmega328P__) || defined(__AVR_ATmega328__) || defined(__AVR_ATtiny85__)) // no USB - maybe BOOTLOADER_BOOTLOADHID instead though?
UDCON = 1;
USBCON = (1 << FRZCLK); // disable USB
UCSR1B = 0;
_delay_ms(5); // 5 seems to work fine
# endif
# ifdef BOOTLOADER_BOOTLOADHID
// force bootloadHID to stay in bootloader mode, so that it waits
// for a new firmware to be flashed
eeprom_write_byte((uint8_t *)1, 0x00);
# endif
// watchdog reset
reset_key = BOOTLOADER_RESET_KEY;
wdt_enable(WDTO_250MS);
for (;;)
;
#endif
}
/* this runs before main() */
void bootloader_jump_after_watchdog_reset(void) __attribute__((used, naked, section(".init3")));
void bootloader_jump_after_watchdog_reset(void) {
#ifndef BOOTLOADER_HALFKAY
if ((MCUCSR & (1 << WDRF)) && reset_key == BOOTLOADER_RESET_KEY) {
reset_key = 0;
// My custom USBasploader requires this to come up.
MCUCSR = 0;
// Seems like Teensy halfkay loader requires clearing WDRF and disabling watchdog.
MCUCSR &= ~(1 << WDRF);
wdt_disable();
// This is compled into 'icall', address should be in word unit, not byte.
# ifdef BOOTLOADER_SIZE
((void (*)(void))((FLASH_SIZE - BOOTLOADER_SIZE) >> 1))();
# else
asm("ijmp" ::"z"(bootloader_start));
# endif
}
#endif
}
Reference in a new issue View git blame Copy permalink