* Fix default ADC_RESOLUTION for ADCv3 (and ADCv4)
Recent ChibiOS update removed ADC_CFGR1_RES_10BIT from the ADCv3 headers
(that macro should not have been there, because ADCv3 has CFGR instead of
CFGR1). Fix the default value for ADC_RESOLUTION to use ADC_CFGR_RES_10BITS
if it is defined (that name is used for ADCv3 and ADCv4).
* Update ADC docs to match the actually used resolution
ADC driver for ChibiOS actually uses the 10-bit resolution by default
(probably to match AVR); fix the documentation accordingly. Also add
both ADC_CFGR_RES_10BITS and ADC_CFGR1_RES_10BIT constants (these names
differ according to the ADC implementation in the particular MCU).
* Fix pinToMux() for B12 and B13 on STM32F3xx
Testing on STM32F303CCT6 revealed that the ADC mux values for B12 and
B13 pins were wrong.
* Add support for all possible analog pins on STM32F1xx
Added ADC mux values for pins A0...A7, B0, B1, C0...C5 on STM32F1xx
(they are the same at least for STM32F103x8 and larger F103 devices, and
also F102, F105, F107 families). Actually tested on STM32F103C8T6
(therefore pins C0...C5 were not tested).
Pins F6...F10, which are present on STM32F103x[C-G] in 144-pin packages,
cannot be supported at the moment, because those pins are connected only
to ADC3, but the ChibiOS ADC driver for STM32F1xx supports only ADC1.
* Add support for all possible analog pins on STM32F4xx
Added ADC mux values for pins A0...A7, B0, B1, C0...C5 and optionally
F3...F10 (if STM32_ADC_USE_ADC3 is enabled). These mux values are
apparently the same for all F4xx devices, except some smaller devices may
not have ADC3.
Actually tested on STM32F401CCU6, STM32F401CEU6, STM32F411CEU6 (using
various WeAct “Blackpill” boards); only pins A0...A7, B0, B1 were tested.
Pins F3...F10 are inside `#if STM32_ADC_USE_ADC3` because some devices
which don't have ADC3 also don't have the GPIOF port, therefore the code
which refers to Fx pins does not compile.
* Fix STM32F3xx ADC mux table in documentation
The ADC driver documentation had some errors in the mux table for STM32F3xx.
Fix this table to match the datasheet and the actual code (mux settings for
B12 and B13 were also tested on a real STM32F303CCT6 chip).
* Add STM32F1xx ADC pins to the documentation
* Add STM32F4xx ADC pins to the documentation
Clarify that the link to the github/forking instructions is a link to how to fork this project. Previous wording implied that the link was to a how-to-use github in general page.
* Add IO Warning to WSL section of Getting Started
* FauxPark suggestion (thanks!)
Co-authored-by: Ryan <fauxpark@gmail.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
* Improve upon the 'Caveats' section of the Layers and Mod-Tap documentation
* Update docs/mod_tap.md
Co-authored-by: Ryan <fauxpark@gmail.com>
* Update docs/feature_layers.md
Co-authored-by: Ryan <fauxpark@gmail.com>
* Update docs/mod_tap.md
Co-authored-by: Ryan <fauxpark@gmail.com>
* Added a line saying that remote desktop problems may also be mitigated by defining TAP_CODE_DELAY
* Update docs/mod_tap.md
Co-authored-by: Ryan <fauxpark@gmail.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
* Add a command to format json files
* change to work after rebase
* add test for qmk format-json
* add documentation for qmk format-json
* Update lib/python/qmk/cli/format/json.py
* Added new section to docs: Checking Modifier State
* Added id anchors to all headers in modifiers docs
* Added a Wikipedia link to bitwise operators and...
crosslinked to the QMK macro docs.
* Added an explanation on the format of mod bitmask
* Added .md extension to hyperlinks to macros docs
* Corrected mod mask order and changed notation
* Documented add_oneshot_mods and del_oneshot_mods
* Mentioned modifier checks in the macro docs
* Explained strict modifier checking
i.e. using `get_mods() & MOD_MASK == MOD_MASK` instead of simply
`get_mods() & MOD_MASK`
* Added (un)register_mods to the docs
* Put left term of comparison in parens
* add podman support to docker_build.sh script
* break out runtime into the RUNTIME variable
* allows RUNTIME to be set by the user
* decides on docker or podman if docker isn't avaible
* rewrote check for docker-machine to account only for docker runtime
* put --user arg into a variable only to be used with docker
this is not needed with podman as podman maps the containers root id
to the users id.
* add podman to getting_started_docker documentation
* Add suggestion for indirect unicode input on Linux
I have used this approach myself with great success, and it seems to be the only good solution that doesn't involve IBus.
* Elaborate on keyboard layout on Linux
This should be enough to allow people to figure out how to add custom characters to a Linux keyboard layout.
* restore main readme.md
* add ChangeLog entry for 2021-02-27 develop branch - initial version
* update Docs; consolidate sidebar entries to new Breaking Changes History doc
* Changelog update
- concatenate similar changes as one list item
- unify change formatting (remove [bracketed] headings and trailing periods)
- item sorting improvement
* update Changes Requiring User Action section
Detail the changes regarding keyboard relocations/additions/deletions.
* add entry for fauxpark's user keymap cleanup for config.h/rules.mk
* add link to Jacky Studio bugfix PR
* add link for "ChibiOS conf migrations... take 15"
* add links for "Make LAYOUT parsing more robust" and "Massdrop develop rgb fix"
* remove sort sequence numbers
* rename Breaking Changes History page
Renames the Breaking Changes History page to "Past Breaking Changes".
* update schedule in Breaking Changes Overview
* suggestions/changes per tzarc
* skully's changes
* add entry for "Fix develop" (PR 12039)
Co-authored-by: Nick Brassel <nick@tzarc.org>
Co-authored-by: Zach White <skullydazed@gmail.com>
Current wording of IGNORE_MOD_TAP_INTERRUPT is incorrect, and very confusing when attempting to correct a somewhat common issue for quick typists that have Mod-Tap on a commonly used key. Research indicates this wording has been incorrect for some time, and has tripped up others attempting to solve the issue of Mod + Key being sent, when Tap + Key is expected after quickly pressing keys.
* Redo Arm DAC implementation for additive, wavetable synthesis, sample playback
changes by Jack Humbert on an implementation for DAC audio on arm/chibios platforms
this commits bundles the changes from the arm-dac-work branch focused on audio/audio_arm.* into one commit (leaving out the test-keyboard)
f52faeb5d (origin/arm-dac-work) add sample and wavetable examples, parsers for both
-> only the changes on audio_arm_.*, the keyboard related parts are split off to a separate commit
bfe468ef1 start morphing wavetable
474d100b5 refined a bit
208bee10f play_notes working
3e6478b0b start in-place documentation of dac settings
3e1826a33 fixed blip (rounding error), other waves, added key selection (left/right)
73853d651 5 voices at 44.1khz
dfb401b95 limit voices to working number
9632b3379 configuration for the ez
6241f3f3b notes working in a new way
* Redo Arm DAC implementation for additive, wavetable synthesis, sample playback
changes by Jack Humbert on an implementation for DAC audio on arm/chibios platforms
this commit splits off the plank example keymap from commit
f52faeb5d (origin/arm-dac-work) add sample and wavetable examples, parsers for both
* refactoring: rename audio_ to reflect their supported hardware-platform and audio-generation method: avr vs arm, and pwm vs dac
* refactoring: deducplicate ISR code to update the pwm duty-cycle and period in the avr-pwm-implementation
pulls three copies of the same code into one function
which should improve readability and maintainability :-)
* refactoring: move common code of arm and avr implementation into a separate/new file
* refactoring: audio_avr_pwm, renaming defines to decouple them from actually used timers, registers and ISRs
* refactoring: audio_avr_pwm - replacing function defines with plain register defines
aligns better with other existing qmk code (and the new audio_arm_pwm) doing similar pwm thing
* add audio-arm-pwm
since not all STM32 have a DAC onboard (STM32F2xx and STM32F3xx), pwm-audio is an alternative (STM32F1xx)
this code works on a "BluePill" clone, with an STM32F103C8B
* clang-format changes on quantum/audio/* only
* audio_arm_dac: stopping the notes caused screeching when using the DAC audio paths
* audio_arm_pwm: use pushpull on the pin; so that a piezzo can be hooked up direclty without additional components (opendrain would require an external pullup)
* refactoring: remove unused file from/for atmel-avr chips
* refactoring: remove unused (avr) wavetable file
* audio_arm_dac: adapt dac_end callback to changed chibios DAC api
the previous chibios (17.6.0) passed along a pointer into the buffer plus a sample_count (which are/already where included in the DACDrivre object) - the current chibios (19.1.0) only passes the driver object.
this patch ports more or less exactly what the previous chibios ISR code did: either have the user-callback work the first or second half of the buffer (dacsample_t pointer, with half the DAC_BUFFER_SIZE samples) by adjusting the pointer and sample count
* audio-arm-dac: show a compile-warning on undefined audio-pins
Co-Authored-By: Drashna Jaelre <drashna@live.com>
* audio_arm_dac: switch from exemplary wavetable generation to sine only
sine+triangle+squrare is exemplary, and not realy fit for "production" use
'stairs' are usefull for debugging (hardware, with an oscilloscope)
* audio_arm_dac: enable output buffers in the STM32
to drive external loads without any additional ciruitry - external opamps and such
* audio: prevent out-of-bounds array access
* audio_arm_dac: add output-frequency correcting factor
* audio_arm_pwm: get both the alternate-function and pm-callback variants back into working condition
and do some code-cleanup, refine documentation, ...
* audio_arm_pwm: increase pwm frequency for "higher fidelity"
on the previous .frequency=100000 higher frequency musical notes came out wrong
(frequency measured on a Tektronix TDS2014B)
note | freq | arm-pwm
C2 | 65.4 | 65.491
C5 | 523.25 | 523.93
C6 | 1046.5 | 1053.38
C7 | 2093 | 2129
C8 | 4186 | 4350.91
with .frequency = 500000
C8 | 4186 | 4204.6
* audio refactoring: remove unused variables
* audio_arm_dac: calibrate note tempo: with a tempo of 60beats-per-second a whole-note should last for exactly one second
* audio: allow feature selection in rules.mk
so the user can switch the audio driver between DAC and PWM on STM32 boards which support both (STM32F2 and up)
or select the "pin alternate" pwm mode, for example on STM32F103
* audio-refactoring: move codeblocks in audio.[ch] into more coherent groups
and add some inline documentation
* audio-refactoring: cleanup and streamline common code between audio_arm_[dac|pwm]
untangeling the relation between audio.c and the two drivers
and adding more documenting comments :-)
* audio_avr_pwm: getting it back into working condition, and cleanup+refactor
* audio-refactoring: documentation and typo fixes
Co-Authored-By: Nick Brassel <nick@tzarc.org>
* audio-refactoring: cleanup defines, inludes and remove debug-prints
* audio_chibios_dac: define&use a minimal sampling rate, based on the available tone-range
to ease up on the cpu-load, while still rendering the higher notes/tones sufficiently
also reenable the lower tones, since with the new implementation there is no evidence of them still beeing 'bugged'
* audio-refactoring: one common AUDIO_MAX_VOICES define for all audio-drivers
* audio-chibios-pwm: pwm-pin-allternate: make the the timer, timer-channel and alternate function user-#definable
* audio_chibios_dac: math.h has fmod for this
* Redo Arm DAC implementation for additive, wavetable synthesis, sample playback
update Jack Humberts dac-example keymaps for the slight changes in the audio-dac interface
* audio-refactoring: use a common AUDIO_PIN configuration switch instead of defines
have the user select a pin by configuration in rules.mk instead of a define in config.h
has the advantage of beeing in a common form/pattern across all audio-driver implementations
* audio-refactoring: switch backlight_avr.c to the new AUDIO_PIN defines
* audio-common: have advance_note return a boolean if the note changed, to the next one in the melody beeing played
* audio-chibios-pwm: fix issue with ~130ms silence between note/frequency changes while playing a SONG
through trial,error and a scope/logic analyzer figured out Chibios-PWMDriver (at least in the current version) misbehaves if the initial period is set to zero (or one; two seems to work); when thats the case subsequent calls to 'pwmChhangePeriod' + pwmEnableChannel took ~135ms of silence, before the PWM continued with the new frequency...
* audio-refactoring: get 'play_note' working again
with a limited number of available voices (say AUDIO_VOICES_MAX=1) allow new frequencies to be played, by discarding the oldest one in the 'frequencies' queue
* audio: set the fallback driver to DAC for chibios and PWM for all others (==avr at the moment)
* audio-refactoring: moore documentation
and some cleanup
* audio-avr-pwm: no fallback on unset AUDIO_PIN
this seems to be the expected behaviour by some keyboards (looking at ckeys/handwire_101:default) which otherwise fail to build because the firmware-image ends up beeing too large for the atmega... so we fail silently instead to keep travis happy
* audio-refactoring: untangling terminology: voice->tone
the code actually was working on tones (combination of pitch/frequency, duration, timbre, intensity/volume) and not voices (characteristic sound of an instrument; think piano vs guitar, which can be played together, each having its own "track" = voice on a music sheet)
* audio-pwm: allow freq=0 aka a pause/rest in a SONG
continue processing, but do not enable pwm units, since freq=0 wouldn't produce any sound anyway (and lead to division by zero on that occasion)
* audio-refactoring: audio_advance_note -> audio_advance_state
since it does not only affect 'one note', but the internally kept state as a whole
* audio-refactoring: untangling terminology: polyphony
the feature om the "inherited" avr code has little to do with polyphony (see wikipedia), but is more a time-multiplexing feature, to work around hardware limitations - like only having one pwm channel, that could on its own only reproduce one voice/instrument at a time
* audio-chibios-dac: add zero-crossing feature
have tones only change/stop when the waveform approaches zero - to avoid audible clicks
note that this also requires the samples to start at zero, since the internally kept index into the samples is reset to zero too
* audio-refactoring: feature: time-multiplexing of tones on a single output channel
this feature was in the original avr-pwm implementation misnomed as "polyphony"
with polyphony_rate and so on; did the same thing though: time-multiplexing multiple active notes so that a single output channel could reproduce more than one note at a time (which is not the same as a polyphony - see wikipedia :-) )
* audio-avr-pwm: get music-mode working (again) on AVRs
with both pwm channels, or either one of the two :-)
play_notes worked already - but music_mode uses play_note
* audio-refactoring: split define MAX_SIMULTANEOUS_TONES -> TONE_STACKSIZE
since the two cases are independant from one another, the hardware might impose limitations on the number of simultaneously reproducable tones, but the audio state should be able to track an unrelated number of notes recently started by play_note
* audio-arm-dac: per define selectable sample-luts
plus generation script in ./util
* audio-refactoring: heh, avr has a MIN...
* audio-refactoring: add basic dac audio-driver based on the current/master implementation
whereas current=d96380e65496912e0f68e6531565f4b45efd1623
which is the state of things before this whole audio-refactoring branch
boiled down to interface with the refactored audio system = removing all
redundant state-managing and frequency calculation
* audio-refactoring: rename audio-drivers to driver_$PLATFORM_$DRIVER
* audio-arm-pwm: split the software/hardware implementations into separate files
which saves us partially from a 'define hell', with the tradeoff that now two somewhat similar chibios_pwm implementations have to be maintained
* audio-refactoring: update documentation
* audio-arm-dac: apply AUDIO_PIN defines to driver_chibios_dac_basic
* audio-arm-dac: dac_additive: stop the hardware when the last sample completed
the audio system calls for a driver_stop, which is delayed until the current sample conversion finishes
* audio-refactoring: make function-namespace consistent
- all (public) audio functions start with audio_
- also refactoring play*_notes/tones to play*_melody, to visually distance it a bit from play*_tone/_note
* audio-refactoring: consistent define namespace: DAC_ -> AUDIO_DAC_
* audio-arm-dac: update (inline) documentation regarding MAX for sample values
* audio-chibios-dac: remove zero-crossing feature
didn't quite work as intended anyway, and stopping the hardware on close-to-zero seems to be enought anyway
* audio-arm-dac: dac_basic: respect the configured sample-rate
* audio-arm-pwm: have 'note_timbre' influence the pwm-duty cycle
like it already does in the avr implementation
* audio-refactoring: get VIBRATO working (again)
with all drivers (verified with chibios_[dac|pwm])
* audio-arm-dac: zero-crossing feature (Mk II)
wait for the generated waveform to approach 'zero' before either turning off the output+timer or switching to the current set of active_tones
* audio-refactoring: re-add note-resting -> introduce short_rest inbetween
- introduce a short pause/rest between two notes of the same frequency, to separate them audibly
- also updating the refactoring comments
* audio-refactoring: cleanup refactoring remnants
remove the former avr-isr code block - since all its features are now refactored into the different parts of the current system
also updates the TODOS
* audio-refactoring: reserve negative numbers as unitialized frequencies
to allow the valid tone/frequency f=0Hz == rest/pause
* audio-refactoring: FIX: first note of melody was missing
the first note was missing because 'goto_next_note'=false overrode a state_change=true of the initial play_tone
and some code-indentations/cleanup of related parts
* audio-arm-dac: fix hardware init-click
due to wron .init= value
* audio-refactoring: new conveniance function: audio_play_click
which can be used to further refactor/remove fauxclicky (avr only) and/or the 'clicky' features
* audio-refactoring: clang-format on quantum/audio/*
* audio-avr-pwm: consecutive notes of the same frequency get a pause inserted inbetween by audio.c
* audio-refactoring: use milliseconds instead of seconds for 'click' parameters
clicks are supposed to be short, seconds make little sense
* audio-refactoring: use timer ticks instead of counters
local counters were used in the original (avr)ISR to advance an index into the lookup tables (for vibrato), and something similar was used for the tone-multiplexing feature
decoupling these from the (possibly irregular) calls to advance_state made sesne, since those counters/lookups need to be in relation to a wall-time anyway
* audio-refactoring: voices.c: drop 'envelope_index' counter in favour of timer ticks
* audio-refactoring: move vibrato and timbre related parts from audio.c to voices.c
also drops the now (globally) unused AUDIO_VIBRATO/AUDIO_ENABLE_VIBRATO defines
* audio.c: use system-ticks instead of counters the drivers have to take care of for the internal state posision
since there already is a system-tick with ms resolution, keeping count separatly with each driver implementation makes little sense; especially since they had to take special care to call audio_advance_state with the correct step/end parameters for the audio state to advance regularly and with the correct pace
* audio.c: stop notes after new ones have been started
avoids brief states of with no notes playing that would otherwise stop the hardware and might lead to clicks
* audio.c: bugfix: actually play a pause
instead of just idling/stopping which lead the pwm drivers to stop entirely...
* audio-arm-pwm: pwm-software: add inverted output
new define AUDIO_PIN_ALT_AS_NEGATIVE will generate an inverted signal on the alternate pin, which boosts the volume if a piezo is connected to both AUDIO_PIN and AUDIO_PIN_ALT
* audio-arm-dac: basic: handle piezo configured&wired to both audio pins
* audio-refactoring: docs: update for AUDIO_PIN_ALT_AS_NEGATIVE and piezo wiring
* audio.c: bugfix: use timer_elapsed32 instad of keeping timestamps
avoids running into issues when the uint32 of the timer overflows
* audio-refactoring: add 'pragma once' and remove deprecated NOTE_REST
* audio_arm_dac: basic: add missing bracket
* audio.c: fix delta calculation
was in the wrong place, needs to use the 'last_timestamp' before it was reset
* audio-refactoring: buildfix: wrong legacy macro for set_timbre
* audio.c: 16bit timerstamps suffice
* audio-refactoring: separate includes for AVR and chibios
* audio-refactoring: timbre: use uint8 instead of float
* audio-refactoring: duration: use uint16 for internal per-tone/note state
* audio-refactoring: tonemultiplexing: use uint16 instead of float
* audio-arm-dac: additive: set second pin output-low
used when a piezo is connected to AUDIO_PIN and AUDIO_PIN_ALT, with PIN_ALT_AS_NEGATIVE
* audio-refactoring: move AUDIO_PIN selection from rules.mk to config.h
to be consistent with how other features are handled in QMK
* audio-refactoring: buildfix: wrong legacy macro for set_tempo
* audio-arm-dac: additive: set second pin output-low -- FIXUP
* audio.c: do duration<>ms conversion in uint instead of float
on AVR, to save a couple of bytes in the firmware size
* audio-refactoring: cleanup eeprom defines/usage
for ARM, avr is handled automagically through the avr libc and common_features.mk
Co-Authored-By: Drashna Jaelre <drashna@live.com>
* audio.h: throw an error if OFF is larger than MAX
* audio-arm-dac: basic: actually stop the dac-conversion on a audio_driver_stop
to put the output pin in a known state == AUDIO_DAC_OFF_VALUE, instead of just leaving them where the last conversion was... with AUDIO_PIN_ALT_AS_NEGATIVE this meant one output was left HIGH while the other was left LOW
one CAVEAT: due to this change the opposing squarewave when using both A4 and A5 with AUDIO_PIN_ALT_AS_NEGATIVE
show extra pulses at the beginning/end on one of the outputs, the two waveforms are in sync otherwise.
the extra pusles probably matter little, since this is no high-fidelity sound generation :P
* audio-arm-dac: additive: move zero-crossing code out of dac_value_generate
which is/should be user-overridable == simple, and doing one thing: providing sample values
state-transitions necessary for the zero crossing are better handled in the surrounding loop in the dac_end callback
* audio-arm-dac: dac-additive: zero-crossing: ramping up or down
after a start trigger ramp up: generate values until zero=OFF_VALUE is reached, then continue normally
same in reverse for strop trigger: output values until zero is reached/crossed, then keep OFF_VALUE on the output
* audio-arm-dac: dac-additive: BUGFIX: return OFF_VALUE when a pause is playing
fixes a bug during SONG playback, which suddenly stopped when it encoutnered a pause
* audio-arm-dac: set a sensible default for AUDIO_DAC_VALUE_OFF
1/2 MAX was probably exemplary, can't think of a setup where that would make sense :-P
* audio-arm-dac: update synth_sample/_wavetable for new pin-defines
* audio-arm-dac: default for AUDIO_DAC_VALUE_OFF
turned out that zero or max are bad default choices:
when multiple tones are played (>>5) and released at the same time (!), due to the complex waveform never reaching 'zero' the output can take quite a while to reach zero, and hence the zero-crossing code only "releases" the output waaay to late
* audio-arm-dac: additive: use DAC for negative pin
instead of PAL, which only allows the pin to be configured as output; LOW or HIGH
* audio-arm-dac: more compile-time configuration checks
* audio-refactoring: typo fixed
* audio-refactoring: clang-format on quantum/audio/*
* audio-avr-pwm: add defines for B-pin as primary/only speaker
also updates documentation.
* audio-refactoring: update documentation with proton-c config.h example
* audio-refactoring: move glissando (TODO) to voices.c
refactored/saved from the original glissando implementation in then upstream-master:audio_avr.c
still needs some work though, as it is now the calculation *should* work, but the start-frequency needs to be tracked somewhere/somehow; not only during a SONG playback but also with user input?
* audio-refactoring: cleanup: one round of aspell -c
* audio-avr-pwm: back to AUDIO_PIN
since config_common.h expands them to plain integers, the AUDIO_PIN define can directly be compared to e.g. B5
so there is no need to deal with separate defines like AUDIO_PIN_B5
* audio-refactoring: add technical documentation audio_driver.md
which moves some in-code documentation there
* audio-arm-dac: move AUDIO_PIN checks into c-code
instead of doing everything with the preprocessor, since A4/A5 do not expand to simple integers, preprocessor int-comparison is not possible. but necessary to get a consistent configuration scheme going throughout the audio-code... solution: let c-code handle the different AUDIO_PIN configurations instead (and leave code/size optimizations to the compiler)
* audio-arm-dac: compile-fix: set AUDIO_PIN if unset
workaround to get the build going again, and be backwarts compatible to arm-keyboards which not yet set the AUDIO_PIN define. until the define is enforced through an '#error"
* audio-refactoring: document tone-multiplexing feature
* audio-refactoring: Apply suggestions from documentation review
Co-authored-by: James Young <18669334+noroadsleft@users.noreply.github.com>
* audio-refactoring: Update docs/audio_driver.md
* audio-refactoring: docs: fix markdown newlines
Terminating a line in Markdown with <space>-<space>-<linebreak> creates an HTML single-line break (<br>).
Co-authored-by: James Young <18669334+noroadsleft@users.noreply.github.com>
* audio-arm-dac: additive: fix AUDIO_PIN_ALT handling
* audio-arm-pwm: align define naming with other drivers
Co-authored-by: Joel Challis <git@zvecr.com>
* audio-refactoring: set detault tempo to 120
and add documentation for the override
* audio-refactoring: update backlight define checks to new AUDIO_PIN names
* audio-refactoring: reworking PWM related defines
to be more consistent with other QMK code
Co-authored-by: Joel Challis <git@zvecr.com>
* audio-arm: have the state-update-timer user configurable
defaulting to GPTD6 or GPTD8 for stm32f2+ (=proton-c)
stm32f1 might need to set this to GPTD4, since 6 and 8 are not available
* audio-refactoring: PLAY_NOTE_ARRAY was already removed in master
* Add prototype for startup
* Update chibiOS dac basic to disable pins on stop
* Add defaults for Proton C
* avoid hanging audio if note is completely missed
* Don't redefine pins if they're already defined
* Define A4 and A5 for CTPC support
* Add license headers to keymap files
* Remove figlet? comments
* Add DAC config to audio driver docs
* Apply suggestions from code review
Co-authored-by: Jack Humbert <jack.humb@gmail.com>
* Add license header to py files
* correct license header
* Add JohSchneider's name to modified files
AKA credit where credit's due
* Set executable permission and change interpeter
* Add 'wave' to pip requirements
* Improve documentation
* Add some settings I missed
* Strip AUDIO_DRIVER to parse the name correctly
* fix depreciated
* Update util/audio_generate_dac_lut.py
Co-authored-by: Jack Humbert <jack.humb@gmail.com>
* Fix type in clueboard config
* Apply suggestions from tzarc
Co-authored-by: Nick Brassel <nick@tzarc.org>
Co-authored-by: Johannes <you@example.com>
Co-authored-by: JohSchneider <JohSchneider@googlemail.com>
Co-authored-by: Nick Brassel <nick@tzarc.org>
Co-authored-by: James Young <18669334+noroadsleft@users.noreply.github.com>
Co-authored-by: Joel Challis <git@zvecr.com>
Co-authored-by: Joshua Diamond <josh@windowoffire.com>
Co-authored-by: Jack Humbert <jack.humb@gmail.com>
* add feature_unicode.md translation
* consolidate sentence end
* update based on comment
* update based on comment
* update based on comment
* update based on comment
* LED Matrix: add led_matrix_types.h and implement g_led_config
* Set correct flags for non-"modifier" LEDs
* Clean up docs a little
* Add license headers for [led,rgb]_matrix_types.h
* Improve Pointing Device report sending
* Hide old report behind preprocessors too
* put host_mouse_send() in curly brackets
* Remove POINTING_DEVICE_ALWAYS_SEND_REPORT functionality
* Fix typo
* fix function ref in docs
Co-authored-by: James Young <18669334+noroadsleft@users.noreply.github.com>
Co-authored-by: James Young <18669334+noroadsleft@users.noreply.github.com>
* resolve race condition between suspend and wake in LUFA
* avoid multiple calls to suspend_power_down() / suspend_wakeup_init()
* Remove duplicate suspend_power_down_kb() call
* pause on wakeup to wait for USB state to settle
* need the repeated suspend_power_down() (that's where the sleep is)
* more efficient implementation
* fine tune the pause after sending wakeup
* speculative chibios version of pause-after-wake
* make wakeup delay configurable, and adjust value
* better location for wakeup delay
* generate rules.mk from a json mapping
* generate rules.mk from a json mapping
* support for config.h from json maps
* improve the mapping system
* document the mapping system
* move data/maps to data/mappings
* fix flake8 errors
* fixup LED_MATRIX_DRIVER
* remove product and description from the vision_division keymap level
* reduce the complexity of generate-rules-mk
* add tests for the generate commands
* fix qmk doctor when submodules are not clean
* at90usb162 support
* fix missing bracket
* Apply suggestions from code review
Co-authored-by: Ryan <fauxpark@gmail.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
* Add support for 8 buttons to mouse report
This includes support for 8 buttons in mousekeys. However, this does move the keys around due to the fact that the last mousekey keycode is already 0xFF, so any past that would not work with register_code and the like, breaking them for tap hold keys, encoders, and other features.
* Update mouse key docs
* Add changes based on feedback
* Fix VUSB report size comment
Because drashna red gud
* Fix typo in action.c
* Fix IS_MOUSE_BUTTON check
* Change start range for mousekeys so that the end is 0xFF properly
* condense mousekeys check
* Fix minor typo in "General FAQ"
"want to do brand it with QMK" -> "want to brand it with QMK"
* Reword some of "Debugging FAQ" & "Miscellaneous FAQ".
Mostly grammatical wording of some parts and missing capitalization
* first pass
* firmware firmware?
* Split out debug + testing docs
* tidy up duplicate css
* Add extra info to debug example
Co-authored-by: Drashna Jaelre <drashna@live.com>
Co-authored-by: Drashna Jaelre <drashna@live.com>
* add support for --clean to compile and flash
* compile standalone JSON keymaps without polluting the tree
* Add support for passing environment vars to make
* make flake8 happy
* document changes to qmk compile and flash
* add -e support to json export compiling
* Fix python 3.6
* honor $MAKE
* add support for parallel builds
* add byte order bgr for ws2812
* update docs for driver change
* Update ws2812_driver.md
* Update docs/ws2812_driver.md
Co-authored-by: Ryan <fauxpark@gmail.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
* Update feature_rgblight.md
The note is meant to let people know that this is specific to RGB Backlight and does not work with RGB Matrix based implementations.
* Update docs/feature_rgblight.md
Co-authored-by: Drashna Jaelre <drashna@live.com>
Co-authored-by: Drashna Jaelre <drashna@live.com>
* use the schema to eliminate custom code
* Update docs/reference_info_json.md
Co-authored-by: Ryan <fauxpark@gmail.com>
* make flake8 happy
* bugfix
* do not overwrite make vars from json
Co-authored-by: Ryan <fauxpark@gmail.com>
* Make parameters from info.json available to the build system
* move all clueboard settings to info.json
* code formatting
* make flake8 happy
* make flake8 happy
* make qmk lint happy
* Add support for specifying led indicators in json
* move led indicators to the clueboard info.json
* Apply suggestions from code review
Co-authored-by: Erovia <Erovia@users.noreply.github.com>
* add missing docstring
Co-authored-by: Erovia <Erovia@users.noreply.github.com>
* Added mac variant of portuguese keymap
This keymap is very similar to the existing portuguese keymap, but
some symbols are moved around.
Apply suggestions from code review
Corrected whitespace and implemented some suggested changes.
Co-authored-by: Ryan <fauxpark@gmail.com>
Converted some spaces to nbsp
Added sendstring ISO version
* Apply suggestions from code review
Added suggestions from code review
Co-authored-by: Ryan <fauxpark@gmail.com>
* Replaced space with nbsp
* Corrected 2 chars in ascii_to_shift_lut
{ and } require shift
Co-authored-by: Ryan <fauxpark@gmail.com>
* Rewrite APA102 support
The APA102 source was broken by commit 16a15c1cfc as it did not include the
quantum header. This commit addresses that, as well as other issues with
transferring bytes over the SPI interface, i.e. it was not setting the
clock pin back to low after sending a bit.
The deviation when sending the end frame is kept, but updated to the
latest from the referenced project.
Finally, these changes expose the global LED brightness parameter
of the APA102. Brightness values are configurable through
`APA102_DEFAULT_BRIGHTNESS` and `APA102_MAX_BRIGHTNESS`.
* Fix typo in led brightness extern
* Move driver out of AVR directory and add delay for ARM
* Experimental APA102 support on AVR and ARM
Co-authored-by: Alde Rojas <hello@alde.io>
* Refactor apa102_send_byte() calls to a loop
* Implement io_wait function for ARM
* Move APA102 drivers to own directory, fix copyright notice
* Add APA102 keymap to handwired/onekey
* Simplify RGBLIGHT_ENABLE/DRIVER option handling
Co-authored-by: Mikkel Jeppesen <2756925+Duckle29@users.noreply.github.com>
* Add tabs to getting started page
* Review comments
Co-authored-by: Ryan <fauxpark@gmail.com>
* Align with current theme
* Update docs/newbs_getting_started.md
Co-authored-by: Ryan <fauxpark@gmail.com>
* Apply suggestions from code review
Co-authored-by: Ryan <fauxpark@gmail.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
It looks like features.md was deprecated and content was split into other files. This results in a broken link on the main page which, if removed, would have no impact to the remainder of the documentation. This would also:
resolve#9239resolve#10293resolve#10447
* Update feature_rgb_matrix.md
Added more clarification on how to use a newly created rgb effect as it was unclear that the prefix 'RGB_MATRIX_CUSTOM_' had to be added.
Also included an example consistent with the documentation example.
* Update docs/feature_rgb_matrix.md
Co-authored-by: Ryan <fauxpark@gmail.com>
* Update docs/feature_rgb_matrix.md
Co-authored-by: Joel Challis <git@zvecr.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
Co-authored-by: Joel Challis <git@zvecr.com>
* Add modifier state to the split transport
This adds modifier state to the i2c and serial transport for split
keyboards. The purpose of this is to allow e.g. displaying modifier
state on the slave side of a split keyboard on an oled. This adds one
byte to the data transferred between halves.
This also fixes a missing ifdef guard for BLACKLIGHT_ENABLE.
Break modifiers into real/weak/oneshot
Fix incorrect slave serial mod setting
Fix typo in serial weal mod setter
Fix build errors for the I2C code that I introduced
Code cleanup and formatting per project preferences
Correctly get oneshot mods
Fix missing braces
Remove unneeded ifdef guard
Make the added state transport optional
Add documentation for the new define to enable this feature
Fix stray grave mark
* Fix error introduced in conflict resolution
- Set all other ChibiOS defaults to 'off', when not targeting Proton-C
- Modified all existing F303 boards to point at the QMK_PROTON_C to ensure repeatable binary output
- Modified version.h generation so that SKIP_VERSION=yes generates the same output
* Branch point for 2020 November 28 Breaking Change
* Remove matrix_col_t to allow MATRIX_ROWS > 32 (#10183)
* Add support for soft serial to ATmega32U2 (#10204)
* Change MIDI velocity implementation to allow direct control of velocity value (#9940)
* Add ability to build a subset of all keyboards based on platform.
* Actually use eeprom_driver_init().
* Make bootloader_jump weak for ChibiOS. (#10417)
* Joystick 16-bit support (#10439)
* Per-encoder resolutions (#10259)
* Share button state from mousekey to pointing_device (#10179)
* Add hotfix for chibios keyboards not wake (#10088)
* Add advanced/efficient RGB Matrix Indicators (#8564)
* Naming change.
* Support for STM32 GPIOF,G,H,I,J,K (#10206)
* Add milc as a dependency and remove the installed milc (#10563)
* ChibiOS upgrade: early init conversions (#10214)
* ChibiOS upgrade: configuration file migrator (#9952)
* Haptic and solenoid cleanup (#9700)
* XD75 cleanup (#10524)
* OLED display update interval support (#10388)
* Add definition based on currently-selected serial driver. (#10716)
* New feature: Retro Tapping per key (#10622)
* Allow for modification of output RGB values when using rgblight/rgb_matrix. (#10638)
* Add housekeeping task callbacks so that keyboards/keymaps are capable of executing code for each main loop iteration. (#10530)
* Rescale both ChibiOS and AVR backlighting.
* Reduce Helix keyboard build variation (#8669)
* Minor change to behavior allowing display updates to continue between task ticks (#10750)
* Some GPIO manipulations in matrix.c change to atomic. (#10491)
* qmk cformat (#10767)
* [Keyboard] Update the Speedo firmware for v3.0 (#10657)
* Maartenwut/Maarten namechange to evyd13/Evy (#10274)
* [quantum] combine repeated lines of code (#10837)
* Add step sequencer feature (#9703)
* aeboards/ext65 refactor (#10820)
* Refactor xelus/dawn60 for Rev2 later (#10584)
* add DEBUG_MATRIX_SCAN_RATE_ENABLE to common_features.mk (#10824)
* [Core] Added `add_oneshot_mods` & `del_oneshot_mods` (#10549)
* update chibios os usb for the otg driver (#8893)
* Remove HD44780 References, Part 4 (#10735)
* [Keyboard] Add Valor FRL TKL (+refactor) (#10512)
* Fix cursor position bug in oled_write_raw functions (#10800)
* Fixup version.h writing when using SKIP_VERSION=yes (#10972)
* Allow for certain code in the codebase assuming length of string. (#10974)
* Add AT90USB support for serial.c (#10706)
* Auto shift: support repeats and early registration (#9826)
* Rename ledmatrix.h to match .c file (#7949)
* Split RGB_MATRIX_ENABLE into _ENABLE and _DRIVER (#10231)
* Split LED_MATRIX_ENABLE into _ENABLE and _DRIVER (#10840)
* Merge point for 2020 Nov 28 Breaking Change
* Recommend use of LED Indicator config
* Recommend use of LED Indicator config - update link
* Update quantum/template/ps2avrgb/config.h
Co-authored-by: Ryan <fauxpark@gmail.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
* First pass
* Add config options to docs
* Update some wording
* Slight tidy up of backlight caps logic
* Init pin to correct state
* Move init location
* Reverse default state
* Basic qmk lint command
* check for keymap readme
* change the workflow from qmk info to qmk lint
* add a strict mode
* parsing -> parse
* document qmk lint
* small info logging cleanup
* Apply suggestions from code review
Co-authored-by: Ryan <fauxpark@gmail.com>
* honor --strict in more places
* change the job name to lint
Co-authored-by: Ryan <fauxpark@gmail.com>
This makes it overall easier to package for downstream distributions
instead of keeping tabs with inline documentation.
Signed-off-by: Morten Linderud <morten@linderud.pw>
* Basic keymap parsing finally works
* Add 'keymap.json' creation to the qmk.keymap module
* Add tests and fix formatting
* Fix/exclude flake8 errors
* Convert keymap.c to valid keymap.json
* Fix some errors
* Add tests
* Finalize keymap.json creation, add json template
* Add docs
* Move pygments to the standard requirements
* Add support for nameless layers, fix tests
* Fix things after rebase
* Add missing 'keymap' value.
* Fix missing layer numbers from advanced keycodes
Buckwich noticed that if the advanced keycode / layer toggling key
contains a number, it goes missing.
Now we properly handle them.
Thx for noticing!
* Apply suggestions from code review
* fixup tests
Co-authored-by: Zach White <skullydazed@drpepper.org>
Co-authored-by: skullY <skullydazed@gmail.com>
* Update reference_info_json.md
key_count is now an optional field because it is better to get the keycount by counting the elements in the layout array.
* Updated Japanese documentation as well
* Consolidate udev rules into a single file
* Update rules in doctor.py
* Simplify doctor rule checking
* Fix errors
* Add TMK "FEED" VID to list of deprecated udev rules
* A comma would be nice
* Split rules back up into bootloaders
* Link to docs page in "missing" case
* Add Pololu VID
* Be more specific about Caterina devices, and add LilyPad PID
* Wording & formatting changes in Tapping Force Hold
The Permissive Hold and the Ignore Mod Tap Interrupt sections were also modified to remove the quotes
around "tapping".
* Removed all trailing whitespaces from tap hold doc
* "it's simply really:" → "it's simple really:"
* "This allows to keep the ability" → "This allows keeping the ability"
Used the gerund form of "to keep" in the Tapping Force Hold section of the Tap Hold docs.
Co-authored-by: ridingqwerty <george.g.koenig@gmail.com>
Co-authored-by: ridingqwerty <george.g.koenig@gmail.com>
* add understanding_qmk.md translation
* update based on comment
* update based on comment
* update based on comment
* update based on comment
* update based on comment
* Add information to docs
- If layer z is not a higher layer than both x and y, the layer change code
does not function correctly.
* Update docs/ref_functions.md
* Update docs/ref_functions.md
* Update docs/ref_functions.md
* quantum/debounce: rename debouncing algorithms according to Issue 8763
This is the second attempt at implementation, with no ts_ and cy_ prefixes, since those will be implemented with macros.
* Debouncing documentation: Refactor, add some generic info, and merge into a single document
* add reference_configurator_support.md translation
* update based on comment
* update based on comment
* update based on comment
* update based on comment
* fix link in docs/ja/feature_split_keyboard.md
* fix link in docs/ja/faq_build.md
* fix link in docs/ja/faq_general.md
* fix link in docs/ja/faq_keymap.md
* fix link in docs/ja/how_a_matrix_works.md
* fix link in docs/ja/reference_glossary.md
* add ref_functions.md translation
* modify internal link for ja
* update based on comment
* reflect #9892 change
* update based on comment
* update based on comment
* Better handle LTO_ENABLE
Especially when calling from command line
* Replace LINK_TIME_OPTIMIZATION_ENABLE with LTO_ENABLE
* Remove long for LTO from show_options.mk
