mirrors/opensteno_qmk
1
0
Fork 0
mirror of https://github.com/openstenoproject/qmk synced 2024-11-13 03:54:42 +00:00
Code Issues Projects Releases Packages Wiki Activity
opensteno_qmk/converter/sun_usb
History
tmk 62117e7ea7 Change MCU setting to ATmega32U2
2014-04-25 15:26:11 +09:00
..
command_extra.c Add extra commands Bell/Click to Sun converter 2012-10-21 22:36:44 +09:00
config.h Fix BOOTLOADER_SIZE setting 2013-03-29 11:31:21 +09:00
keymap.c fix hard-coded keys 2013-12-26 21:52:58 -08:00
led.c Add LED feature to Sun converter 2012-10-21 22:12:36 +09:00
Makefile Change MCU setting to ATmega32U2 2014-04-25 15:26:11 +09:00
matrix.c Change MCU setting to ATmega32U2 2014-04-25 15:26:11 +09:00
README Spellchecking converter README files. 2014-01-07 11:03:18 +09:00

README 

Sun to USB keyboard protocol converter
======================================
Target MCU is ATMega32u4 but other USB capable AVR will also work.
Supported keyboards: Sun Type 5 Keyboard, CTCSP SHORT TYPE KEYBOARD(CKUB)

CTCSP SHORT TYPE KEYBOARD: http://imgur.com/a/QIv6p




Connector
---------
  8Pin mini DIN
     ___ ___
    /  |_|  \
   / 8  7  6 \
  | 5    4  3 |
   \_ 2   1 _/
     \_____/  
   (receptacle)

    Wiring:
    Pin mini DIN        MCU
    ----------------------------------
    1   GND             GND
    2   GND             GND
    3   5V
    4   RX/TX(Mouse)
    5   RX              PD3
    6   TX              PD2
    7   GND             GND
    8   5V              VCC


Protocol
--------
Signal: Asynchronous, Negative logic, 1200baud, No Flow control
Frame format: 1-Start bit, 8-Data bits, No-Parity, 1-Stop bit

    AVR USART engine expects positive logic while Sun keyboard signal is negative.
    To use AVR UART engine you need external inverter in front of RX and TX pin.
    Otherwise you can software serial routine to communicate the keyboard.

This converter uses software method, you doesn't need any inverter part.


Commands From System To Keyboard
    0x01 Reset
            Keyboard responds with following byte sequence:
            Success: 0xFF 0x04 0x7F
            Fail:    0x7E 0x01 0x7F
    0x02 Bell On
    0x03 Bell Off
    0x0A Click On
    0x0B Click Off
    0x0E LED
            followed by LED status byte:
            bit: 3       2       1       0
            LED: CapsLk  ScrLk   Compose NumLk
    0x0F Layout
            Keyboard responds with 'Layout Response' 0xFE 0xXX

Commands From Keyboard To System
    0x7F Idle
            means no keys pressed.
    0xFE Layout Response
    0xFF Reset Response(followed by 0x04)
     
Reference
    http://kentie.net/article/sunkbd/page2.htm
    http://kentie.net/article/sunkbd/KBD.pdf


Build Firmware
--------------
Just use 'make'
    $ cd sun_usb
    $ make
Then, load the binary to MCU with your favorite programmer.