qmk_firmware/keyboards/handwired/3dortho14u
Ryan ebb512db82
Debounce defines cleanup (#19742)
* Clean up `DEBOUNCE` in config.h, 0-9

* Clean up `DEBOUNCE` in config.h, A

* Clean up `DEBOUNCE` in config.h, B

* Clean up `DEBOUNCE` in config.h, C

* Clean up `DEBOUNCE` in config.h, D

* Clean up `DEBOUNCE` in config.h, E

* Clean up `DEBOUNCE` in config.h, F

* Clean up `DEBOUNCE` in config.h, G

* Clean up `DEBOUNCE` in config.h, H

* Clean up `DEBOUNCE` in config.h, handwired

* Clean up `DEBOUNCE` in config.h, I

* Clean up `DEBOUNCE` in config.h, J

* Clean up `DEBOUNCE` in config.h, K

* Clean up `DEBOUNCE` in config.h, L

* Clean up `DEBOUNCE` in config.h, M

* Clean up `DEBOUNCE` in config.h, N

* Clean up `DEBOUNCE` in config.h, O

* Clean up `DEBOUNCE` in config.h, P

* Clean up `DEBOUNCE` in config.h, Q

* Clean up `DEBOUNCE` in config.h, R

* Clean up `DEBOUNCE` in config.h, S

* Clean up `DEBOUNCE` in config.h, T

* Clean up `DEBOUNCE` in config.h, U

* Clean up `DEBOUNCE` in config.h, V

* Clean up `DEBOUNCE` in config.h, W

* Clean up `DEBOUNCE` in config.h, X

* Clean up `DEBOUNCE` in config.h, Y

* Clean up `DEBOUNCE` in config.h, Z

* Remove default debounce from info.json

* Migrate non-default debounce to info.json
2023-02-03 19:19:58 +00:00
..
keymaps Revert "handwired/3dortho14u: refactor layout data (#16475)" (#16485) 2022-03-01 15:48:38 -08:00
rev1 Debounce defines cleanup (#19742) 2023-02-03 19:19:58 +00:00
rev2 Debounce defines cleanup (#19742) 2023-02-03 19:19:58 +00:00
readme.md RESET -> QK_BOOT keyboard readme (#18110) 2022-08-20 11:34:17 +01:00

3dortho14u

3dortho14u

A symmetrical 14u wide ortholinear keyboard.

In addition to the 3d printed parts and microcontroller, the following hardware is required:

  • 8 * 12 mm M3 bolt
  • Either:
    • 8 * M3 muts and CA glue OR
    • 8 * 3x3 mm threaded insert
  • Optional:
    • USB daughter board

  • Keyboard Maintainer: xia0
  • Hardware Supported:
    • rev1: Teensy 2.0 (ATmega32u4)
    • rev2: Arduino Pro Micro (ATmega32u4)
  • Hardware Availability: github

Make example for this keyboard (after setting up your build environment):

make 3dortho14u/rev1:default

Flashing example for this keyboard:

make 3dortho14u/rev1:default:flash

See the build environment setup and the make instructions for more information. Brand new to QMK? Start with our Complete Newbs Guide.

Bootloader

Enter the bootloader in 3 ways:

  • Bootmagic reset: Hold down the key at (0,0) in the matrix (usually the top left key or Escape) and plug in the keyboard
  • Physical reset button: Briefly press the button on the back of the PCB - some may have pads you must short instead
  • Keycode in layout: Press the key mapped to QK_BOOT if it is available