forked from mirrors/qmk_firmware
509 lines
16 KiB
C
509 lines
16 KiB
C
/*
|
|
* WARNING: be careful changing this code, it is very timing dependent
|
|
*
|
|
* 2018-10-28 checked
|
|
* avr-gcc 4.9.2
|
|
* avr-gcc 5.4.0
|
|
* avr-gcc 7.3.0
|
|
*/
|
|
|
|
#ifndef F_CPU
|
|
# define F_CPU 16000000
|
|
#endif
|
|
|
|
#include <avr/io.h>
|
|
#include <avr/interrupt.h>
|
|
#include <util/delay.h>
|
|
#include <stddef.h>
|
|
#include <stdbool.h>
|
|
#include "serial.h"
|
|
//#include <pro_micro.h>
|
|
|
|
#ifdef SOFT_SERIAL_PIN
|
|
|
|
# ifdef __AVR_ATmega32U4__
|
|
// if using ATmega32U4 I2C, can not use PD0 and PD1 in soft serial.
|
|
# ifdef USE_AVR_I2C
|
|
# if SOFT_SERIAL_PIN == D0 || SOFT_SERIAL_PIN == D1
|
|
# error Using ATmega32U4 I2C, so can not use PD0, PD1
|
|
# endif
|
|
# endif
|
|
|
|
# define setPinInputHigh(pin) (DDRx_ADDRESS(pin) &= ~_BV((pin)&0xF), PORTx_ADDRESS(pin) |= _BV((pin)&0xF))
|
|
# define setPinOutput(pin) (DDRx_ADDRESS(pin) |= _BV((pin)&0xF))
|
|
# define writePinHigh(pin) (PORTx_ADDRESS(pin) |= _BV((pin)&0xF))
|
|
# define writePinLow(pin) (PORTx_ADDRESS(pin) &= ~_BV((pin)&0xF))
|
|
# define readPin(pin) ((bool)(PINx_ADDRESS(pin) & _BV((pin)&0xF)))
|
|
|
|
# if SOFT_SERIAL_PIN >= D0 && SOFT_SERIAL_PIN <= D3
|
|
# if SOFT_SERIAL_PIN == D0
|
|
# define EIMSK_BIT _BV(INT0)
|
|
# define EICRx_BIT (~(_BV(ISC00) | _BV(ISC01)))
|
|
# define SERIAL_PIN_INTERRUPT INT0_vect
|
|
# elif SOFT_SERIAL_PIN == D1
|
|
# define EIMSK_BIT _BV(INT1)
|
|
# define EICRx_BIT (~(_BV(ISC10) | _BV(ISC11)))
|
|
# define SERIAL_PIN_INTERRUPT INT1_vect
|
|
# elif SOFT_SERIAL_PIN == D2
|
|
# define EIMSK_BIT _BV(INT2)
|
|
# define EICRx_BIT (~(_BV(ISC20) | _BV(ISC21)))
|
|
# define SERIAL_PIN_INTERRUPT INT2_vect
|
|
# elif SOFT_SERIAL_PIN == D3
|
|
# define EIMSK_BIT _BV(INT3)
|
|
# define EICRx_BIT (~(_BV(ISC30) | _BV(ISC31)))
|
|
# define SERIAL_PIN_INTERRUPT INT3_vect
|
|
# endif
|
|
# elif SOFT_SERIAL_PIN == E6
|
|
# define EIMSK_BIT _BV(INT6)
|
|
# define EICRx_BIT (~(_BV(ISC60) | _BV(ISC61)))
|
|
# define SERIAL_PIN_INTERRUPT INT6_vect
|
|
# else
|
|
# error invalid SOFT_SERIAL_PIN value
|
|
# endif
|
|
|
|
# else
|
|
# error serial.c now support ATmega32U4 only
|
|
# endif
|
|
|
|
# define ALWAYS_INLINE __attribute__((always_inline))
|
|
# define NO_INLINE __attribute__((noinline))
|
|
# define _delay_sub_us(x) __builtin_avr_delay_cycles(x)
|
|
|
|
// parity check
|
|
# define ODD_PARITY 1
|
|
# define EVEN_PARITY 0
|
|
# define PARITY EVEN_PARITY
|
|
|
|
# ifdef SERIAL_DELAY
|
|
// custom setup in config.h
|
|
// #define TID_SEND_ADJUST 2
|
|
// #define SERIAL_DELAY 6 // micro sec
|
|
// #define READ_WRITE_START_ADJUST 30 // cycles
|
|
// #define READ_WRITE_WIDTH_ADJUST 8 // cycles
|
|
# else
|
|
// ============ Standard setups ============
|
|
|
|
# ifndef SELECT_SOFT_SERIAL_SPEED
|
|
# define SELECT_SOFT_SERIAL_SPEED 1
|
|
// 0: about 189kbps (Experimental only)
|
|
// 1: about 137kbps (default)
|
|
// 2: about 75kbps
|
|
// 3: about 39kbps
|
|
// 4: about 26kbps
|
|
// 5: about 20kbps
|
|
# endif
|
|
|
|
# if __GNUC__ < 6
|
|
# define TID_SEND_ADJUST 14
|
|
# else
|
|
# define TID_SEND_ADJUST 2
|
|
# endif
|
|
|
|
# if SELECT_SOFT_SERIAL_SPEED == 0
|
|
// Very High speed
|
|
# define SERIAL_DELAY 4 // micro sec
|
|
# if __GNUC__ < 6
|
|
# define READ_WRITE_START_ADJUST 33 // cycles
|
|
# define READ_WRITE_WIDTH_ADJUST 3 // cycles
|
|
# else
|
|
# define READ_WRITE_START_ADJUST 34 // cycles
|
|
# define READ_WRITE_WIDTH_ADJUST 7 // cycles
|
|
# endif
|
|
# elif SELECT_SOFT_SERIAL_SPEED == 1
|
|
// High speed
|
|
# define SERIAL_DELAY 6 // micro sec
|
|
# if __GNUC__ < 6
|
|
# define READ_WRITE_START_ADJUST 30 // cycles
|
|
# define READ_WRITE_WIDTH_ADJUST 3 // cycles
|
|
# else
|
|
# define READ_WRITE_START_ADJUST 33 // cycles
|
|
# define READ_WRITE_WIDTH_ADJUST 7 // cycles
|
|
# endif
|
|
# elif SELECT_SOFT_SERIAL_SPEED == 2
|
|
// Middle speed
|
|
# define SERIAL_DELAY 12 // micro sec
|
|
# define READ_WRITE_START_ADJUST 30 // cycles
|
|
# if __GNUC__ < 6
|
|
# define READ_WRITE_WIDTH_ADJUST 3 // cycles
|
|
# else
|
|
# define READ_WRITE_WIDTH_ADJUST 7 // cycles
|
|
# endif
|
|
# elif SELECT_SOFT_SERIAL_SPEED == 3
|
|
// Low speed
|
|
# define SERIAL_DELAY 24 // micro sec
|
|
# define READ_WRITE_START_ADJUST 30 // cycles
|
|
# if __GNUC__ < 6
|
|
# define READ_WRITE_WIDTH_ADJUST 3 // cycles
|
|
# else
|
|
# define READ_WRITE_WIDTH_ADJUST 7 // cycles
|
|
# endif
|
|
# elif SELECT_SOFT_SERIAL_SPEED == 4
|
|
// Very Low speed
|
|
# define SERIAL_DELAY 36 // micro sec
|
|
# define READ_WRITE_START_ADJUST 30 // cycles
|
|
# if __GNUC__ < 6
|
|
# define READ_WRITE_WIDTH_ADJUST 3 // cycles
|
|
# else
|
|
# define READ_WRITE_WIDTH_ADJUST 7 // cycles
|
|
# endif
|
|
# elif SELECT_SOFT_SERIAL_SPEED == 5
|
|
// Ultra Low speed
|
|
# define SERIAL_DELAY 48 // micro sec
|
|
# define READ_WRITE_START_ADJUST 30 // cycles
|
|
# if __GNUC__ < 6
|
|
# define READ_WRITE_WIDTH_ADJUST 3 // cycles
|
|
# else
|
|
# define READ_WRITE_WIDTH_ADJUST 7 // cycles
|
|
# endif
|
|
# else
|
|
# error invalid SELECT_SOFT_SERIAL_SPEED value
|
|
# endif /* SELECT_SOFT_SERIAL_SPEED */
|
|
# endif /* SERIAL_DELAY */
|
|
|
|
# define SERIAL_DELAY_HALF1 (SERIAL_DELAY / 2)
|
|
# define SERIAL_DELAY_HALF2 (SERIAL_DELAY - SERIAL_DELAY / 2)
|
|
|
|
# define SLAVE_INT_WIDTH_US 1
|
|
# ifndef SERIAL_USE_MULTI_TRANSACTION
|
|
# define SLAVE_INT_RESPONSE_TIME SERIAL_DELAY
|
|
# else
|
|
# define SLAVE_INT_ACK_WIDTH_UNIT 2
|
|
# define SLAVE_INT_ACK_WIDTH 4
|
|
# endif
|
|
|
|
static SSTD_t *Transaction_table = NULL;
|
|
static uint8_t Transaction_table_size = 0;
|
|
|
|
inline static void serial_delay(void) ALWAYS_INLINE;
|
|
inline static void serial_delay(void) { _delay_us(SERIAL_DELAY); }
|
|
|
|
inline static void serial_delay_half1(void) ALWAYS_INLINE;
|
|
inline static void serial_delay_half1(void) { _delay_us(SERIAL_DELAY_HALF1); }
|
|
|
|
inline static void serial_delay_half2(void) ALWAYS_INLINE;
|
|
inline static void serial_delay_half2(void) { _delay_us(SERIAL_DELAY_HALF2); }
|
|
|
|
inline static void serial_output(void) ALWAYS_INLINE;
|
|
inline static void serial_output(void) { setPinOutput(SOFT_SERIAL_PIN); }
|
|
|
|
// make the serial pin an input with pull-up resistor
|
|
inline static void serial_input_with_pullup(void) ALWAYS_INLINE;
|
|
inline static void serial_input_with_pullup(void) { setPinInputHigh(SOFT_SERIAL_PIN); }
|
|
|
|
inline static uint8_t serial_read_pin(void) ALWAYS_INLINE;
|
|
inline static uint8_t serial_read_pin(void) { return !!readPin(SOFT_SERIAL_PIN); }
|
|
|
|
inline static void serial_low(void) ALWAYS_INLINE;
|
|
inline static void serial_low(void) { writePinLow(SOFT_SERIAL_PIN); }
|
|
|
|
inline static void serial_high(void) ALWAYS_INLINE;
|
|
inline static void serial_high(void) { writePinHigh(SOFT_SERIAL_PIN); }
|
|
|
|
void soft_serial_initiator_init(SSTD_t *sstd_table, int sstd_table_size) {
|
|
Transaction_table = sstd_table;
|
|
Transaction_table_size = (uint8_t)sstd_table_size;
|
|
serial_output();
|
|
serial_high();
|
|
}
|
|
|
|
void soft_serial_target_init(SSTD_t *sstd_table, int sstd_table_size) {
|
|
Transaction_table = sstd_table;
|
|
Transaction_table_size = (uint8_t)sstd_table_size;
|
|
serial_input_with_pullup();
|
|
|
|
// Enable INT0-INT3,INT6
|
|
EIMSK |= EIMSK_BIT;
|
|
# if SOFT_SERIAL_PIN == E6
|
|
// Trigger on falling edge of INT6
|
|
EICRB &= EICRx_BIT;
|
|
# else
|
|
// Trigger on falling edge of INT0-INT3
|
|
EICRA &= EICRx_BIT;
|
|
# endif
|
|
}
|
|
|
|
// Used by the sender to synchronize timing with the reciver.
|
|
static void sync_recv(void) NO_INLINE;
|
|
static void sync_recv(void) {
|
|
for (uint8_t i = 0; i < SERIAL_DELAY * 5 && serial_read_pin(); i++) {
|
|
}
|
|
// This shouldn't hang if the target disconnects because the
|
|
// serial line will float to high if the target does disconnect.
|
|
while (!serial_read_pin())
|
|
;
|
|
}
|
|
|
|
// Used by the reciver to send a synchronization signal to the sender.
|
|
static void sync_send(void) NO_INLINE;
|
|
static void sync_send(void) {
|
|
serial_low();
|
|
serial_delay();
|
|
serial_high();
|
|
}
|
|
|
|
// Reads a byte from the serial line
|
|
static uint8_t serial_read_chunk(uint8_t *pterrcount, uint8_t bit) NO_INLINE;
|
|
static uint8_t serial_read_chunk(uint8_t *pterrcount, uint8_t bit) {
|
|
uint8_t byte, i, p, pb;
|
|
|
|
_delay_sub_us(READ_WRITE_START_ADJUST);
|
|
for (i = 0, byte = 0, p = PARITY; i < bit; i++) {
|
|
serial_delay_half1(); // read the middle of pulses
|
|
if (serial_read_pin()) {
|
|
byte = (byte << 1) | 1;
|
|
p ^= 1;
|
|
} else {
|
|
byte = (byte << 1) | 0;
|
|
p ^= 0;
|
|
}
|
|
_delay_sub_us(READ_WRITE_WIDTH_ADJUST);
|
|
serial_delay_half2();
|
|
}
|
|
/* recive parity bit */
|
|
serial_delay_half1(); // read the middle of pulses
|
|
pb = serial_read_pin();
|
|
_delay_sub_us(READ_WRITE_WIDTH_ADJUST);
|
|
serial_delay_half2();
|
|
|
|
*pterrcount += (p != pb) ? 1 : 0;
|
|
|
|
return byte;
|
|
}
|
|
|
|
// Sends a byte with MSB ordering
|
|
void serial_write_chunk(uint8_t data, uint8_t bit) NO_INLINE;
|
|
void serial_write_chunk(uint8_t data, uint8_t bit) {
|
|
uint8_t b, p;
|
|
for (p = PARITY, b = 1 << (bit - 1); b; b >>= 1) {
|
|
if (data & b) {
|
|
serial_high();
|
|
p ^= 1;
|
|
} else {
|
|
serial_low();
|
|
p ^= 0;
|
|
}
|
|
serial_delay();
|
|
}
|
|
/* send parity bit */
|
|
if (p & 1) {
|
|
serial_high();
|
|
} else {
|
|
serial_low();
|
|
}
|
|
serial_delay();
|
|
|
|
serial_low(); // sync_send() / senc_recv() need raise edge
|
|
}
|
|
|
|
static void serial_send_packet(uint8_t *buffer, uint8_t size) NO_INLINE;
|
|
static void serial_send_packet(uint8_t *buffer, uint8_t size) {
|
|
for (uint8_t i = 0; i < size; ++i) {
|
|
uint8_t data;
|
|
data = buffer[i];
|
|
sync_send();
|
|
serial_write_chunk(data, 8);
|
|
}
|
|
}
|
|
|
|
static uint8_t serial_recive_packet(uint8_t *buffer, uint8_t size) NO_INLINE;
|
|
static uint8_t serial_recive_packet(uint8_t *buffer, uint8_t size) {
|
|
uint8_t pecount = 0;
|
|
for (uint8_t i = 0; i < size; ++i) {
|
|
uint8_t data;
|
|
sync_recv();
|
|
data = serial_read_chunk(&pecount, 8);
|
|
buffer[i] = data;
|
|
}
|
|
return pecount == 0;
|
|
}
|
|
|
|
inline static void change_sender2reciver(void) {
|
|
sync_send(); // 0
|
|
serial_delay_half1(); // 1
|
|
serial_low(); // 2
|
|
serial_input_with_pullup(); // 2
|
|
serial_delay_half1(); // 3
|
|
}
|
|
|
|
inline static void change_reciver2sender(void) {
|
|
sync_recv(); // 0
|
|
serial_delay(); // 1
|
|
serial_low(); // 3
|
|
serial_output(); // 3
|
|
serial_delay_half1(); // 4
|
|
}
|
|
|
|
static inline uint8_t nibble_bits_count(uint8_t bits) {
|
|
bits = (bits & 0x5) + (bits >> 1 & 0x5);
|
|
bits = (bits & 0x3) + (bits >> 2 & 0x3);
|
|
return bits;
|
|
}
|
|
|
|
// interrupt handle to be used by the target device
|
|
ISR(SERIAL_PIN_INTERRUPT) {
|
|
# ifndef SERIAL_USE_MULTI_TRANSACTION
|
|
serial_low();
|
|
serial_output();
|
|
SSTD_t *trans = Transaction_table;
|
|
# else
|
|
// recive transaction table index
|
|
uint8_t tid, bits;
|
|
uint8_t pecount = 0;
|
|
sync_recv();
|
|
bits = serial_read_chunk(&pecount, 7);
|
|
tid = bits >> 3;
|
|
bits = (bits & 7) != nibble_bits_count(tid);
|
|
if (bits || pecount > 0 || tid > Transaction_table_size) {
|
|
return;
|
|
}
|
|
serial_delay_half1();
|
|
|
|
serial_high(); // response step1 low->high
|
|
serial_output();
|
|
_delay_sub_us(SLAVE_INT_ACK_WIDTH_UNIT * SLAVE_INT_ACK_WIDTH);
|
|
SSTD_t *trans = &Transaction_table[tid];
|
|
serial_low(); // response step2 ack high->low
|
|
# endif
|
|
|
|
// target send phase
|
|
if (trans->target2initiator_buffer_size > 0) serial_send_packet((uint8_t *)trans->target2initiator_buffer, trans->target2initiator_buffer_size);
|
|
// target switch to input
|
|
change_sender2reciver();
|
|
|
|
// target recive phase
|
|
if (trans->initiator2target_buffer_size > 0) {
|
|
if (serial_recive_packet((uint8_t *)trans->initiator2target_buffer, trans->initiator2target_buffer_size)) {
|
|
*trans->status = TRANSACTION_ACCEPTED;
|
|
} else {
|
|
*trans->status = TRANSACTION_DATA_ERROR;
|
|
}
|
|
} else {
|
|
*trans->status = TRANSACTION_ACCEPTED;
|
|
}
|
|
|
|
sync_recv(); // weit initiator output to high
|
|
}
|
|
|
|
/////////
|
|
// start transaction by initiator
|
|
//
|
|
// int soft_serial_transaction(int sstd_index)
|
|
//
|
|
// Returns:
|
|
// TRANSACTION_END
|
|
// TRANSACTION_NO_RESPONSE
|
|
// TRANSACTION_DATA_ERROR
|
|
// this code is very time dependent, so we need to disable interrupts
|
|
# ifndef SERIAL_USE_MULTI_TRANSACTION
|
|
int soft_serial_transaction(void) {
|
|
SSTD_t *trans = Transaction_table;
|
|
# else
|
|
int soft_serial_transaction(int sstd_index) {
|
|
if (sstd_index > Transaction_table_size) return TRANSACTION_TYPE_ERROR;
|
|
SSTD_t *trans = &Transaction_table[sstd_index];
|
|
# endif
|
|
cli();
|
|
|
|
// signal to the target that we want to start a transaction
|
|
serial_output();
|
|
serial_low();
|
|
_delay_us(SLAVE_INT_WIDTH_US);
|
|
|
|
# ifndef SERIAL_USE_MULTI_TRANSACTION
|
|
// wait for the target response
|
|
serial_input_with_pullup();
|
|
_delay_us(SLAVE_INT_RESPONSE_TIME);
|
|
|
|
// check if the target is present
|
|
if (serial_read_pin()) {
|
|
// target failed to pull the line low, assume not present
|
|
serial_output();
|
|
serial_high();
|
|
*trans->status = TRANSACTION_NO_RESPONSE;
|
|
sei();
|
|
return TRANSACTION_NO_RESPONSE;
|
|
}
|
|
|
|
# else
|
|
// send transaction table index
|
|
int tid = (sstd_index << 3) | (7 & nibble_bits_count(sstd_index));
|
|
sync_send();
|
|
_delay_sub_us(TID_SEND_ADJUST);
|
|
serial_write_chunk(tid, 7);
|
|
serial_delay_half1();
|
|
|
|
// wait for the target response (step1 low->high)
|
|
serial_input_with_pullup();
|
|
while (!serial_read_pin()) {
|
|
_delay_sub_us(2);
|
|
}
|
|
|
|
// check if the target is present (step2 high->low)
|
|
for (int i = 0; serial_read_pin(); i++) {
|
|
if (i > SLAVE_INT_ACK_WIDTH + 1) {
|
|
// slave failed to pull the line low, assume not present
|
|
serial_output();
|
|
serial_high();
|
|
*trans->status = TRANSACTION_NO_RESPONSE;
|
|
sei();
|
|
return TRANSACTION_NO_RESPONSE;
|
|
}
|
|
_delay_sub_us(SLAVE_INT_ACK_WIDTH_UNIT);
|
|
}
|
|
# endif
|
|
|
|
// initiator recive phase
|
|
// if the target is present syncronize with it
|
|
if (trans->target2initiator_buffer_size > 0) {
|
|
if (!serial_recive_packet((uint8_t *)trans->target2initiator_buffer, trans->target2initiator_buffer_size)) {
|
|
serial_output();
|
|
serial_high();
|
|
*trans->status = TRANSACTION_DATA_ERROR;
|
|
sei();
|
|
return TRANSACTION_DATA_ERROR;
|
|
}
|
|
}
|
|
|
|
// initiator switch to output
|
|
change_reciver2sender();
|
|
|
|
// initiator send phase
|
|
if (trans->initiator2target_buffer_size > 0) {
|
|
serial_send_packet((uint8_t *)trans->initiator2target_buffer, trans->initiator2target_buffer_size);
|
|
}
|
|
|
|
// always, release the line when not in use
|
|
sync_send();
|
|
|
|
*trans->status = TRANSACTION_END;
|
|
sei();
|
|
return TRANSACTION_END;
|
|
}
|
|
|
|
# ifdef SERIAL_USE_MULTI_TRANSACTION
|
|
int soft_serial_get_and_clean_status(int sstd_index) {
|
|
SSTD_t *trans = &Transaction_table[sstd_index];
|
|
cli();
|
|
int retval = *trans->status;
|
|
*trans->status = 0;
|
|
;
|
|
sei();
|
|
return retval;
|
|
}
|
|
# endif
|
|
|
|
#endif
|
|
|
|
// Helix serial.c history
|
|
// 2018-1-29 fork from let's split and add PD2, modify sync_recv() (#2308, bceffdefc)
|
|
// 2018-6-28 bug fix master to slave comm and speed up (#3255, 1038bbef4)
|
|
// (adjusted with avr-gcc 4.9.2)
|
|
// 2018-7-13 remove USE_SERIAL_PD2 macro (#3374, f30d6dd78)
|
|
// (adjusted with avr-gcc 4.9.2)
|
|
// 2018-8-11 add support multi-type transaction (#3608, feb5e4aae)
|
|
// (adjusted with avr-gcc 4.9.2)
|
|
// 2018-10-21 fix serial and RGB animation conflict (#4191, 4665e4fff)
|
|
// (adjusted with avr-gcc 7.3.0)
|
|
// 2018-10-28 re-adjust compiler depend value of delay (#4269, 8517f8a66)
|
|
// (adjusted with avr-gcc 5.4.0, 7.3.0)
|
|
// 2018-12-17 copy to TOP/quantum/split_common/ and remove backward compatibility code (#4669)
|