qmk_firmware/platforms/chibios/drivers/i2c_master.c

210 lines
7.6 KiB
C

/* Copyright 2018 Jack Humbert
* Copyright 2018 Yiancar
* Copyright 2023 customMK
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
/* This library is only valid for STM32 processors.
* This library follows the convention of the AVR i2c_master library.
* As a result addresses are expected to be already shifted (addr << 1).
* I2CD1 is the default driver which corresponds to pins B6 and B7. This
* can be changed.
* Please ensure that HAL_USE_I2C is TRUE in the halconf.h file and that
* STM32_I2C_USE_I2C1 is TRUE in the mcuconf.h file. Pins B6 and B7 are used
* but using any other I2C pins should be trivial.
*/
#include "i2c_master.h"
#include "gpio.h"
#include "chibios_config.h"
#include <string.h>
#include <ch.h>
#include <hal.h>
#ifndef I2C1_SCL_PIN
# define I2C1_SCL_PIN B6
#endif
#ifndef I2C1_SDA_PIN
# define I2C1_SDA_PIN B7
#endif
#ifdef USE_I2CV1
# ifndef I2C1_OPMODE
# define I2C1_OPMODE OPMODE_I2C
# endif
# ifndef I2C1_CLOCK_SPEED
# define I2C1_CLOCK_SPEED 100000 /* 400000 */
# endif
# ifndef I2C1_DUTY_CYCLE
# define I2C1_DUTY_CYCLE STD_DUTY_CYCLE /* FAST_DUTY_CYCLE_2 */
# endif
#else
// The default timing values below configures the I2C clock to 400khz assuming a 72Mhz clock
// For more info : https://www.st.com/en/embedded-software/stsw-stm32126.html
# ifndef I2C1_TIMINGR_PRESC
# define I2C1_TIMINGR_PRESC 0U
# endif
# ifndef I2C1_TIMINGR_SCLDEL
# define I2C1_TIMINGR_SCLDEL 7U
# endif
# ifndef I2C1_TIMINGR_SDADEL
# define I2C1_TIMINGR_SDADEL 0U
# endif
# ifndef I2C1_TIMINGR_SCLH
# define I2C1_TIMINGR_SCLH 38U
# endif
# ifndef I2C1_TIMINGR_SCLL
# define I2C1_TIMINGR_SCLL 129U
# endif
#endif
#ifndef I2C_DRIVER
# define I2C_DRIVER I2CD1
#endif
#ifdef USE_GPIOV1
# ifndef I2C1_SCL_PAL_MODE
# define I2C1_SCL_PAL_MODE PAL_MODE_ALTERNATE_OPENDRAIN
# endif
# ifndef I2C1_SDA_PAL_MODE
# define I2C1_SDA_PAL_MODE PAL_MODE_ALTERNATE_OPENDRAIN
# endif
#else
// The default PAL alternate modes are used to signal that the pins are used for I2C
# ifndef I2C1_SCL_PAL_MODE
# define I2C1_SCL_PAL_MODE 4
# endif
# ifndef I2C1_SDA_PAL_MODE
# define I2C1_SDA_PAL_MODE 4
# endif
#endif
static const I2CConfig i2cconfig = {
#if defined(USE_I2CV1_CONTRIB)
I2C1_CLOCK_SPEED,
#elif defined(USE_I2CV1)
I2C1_OPMODE,
I2C1_CLOCK_SPEED,
I2C1_DUTY_CYCLE,
#elif defined(WB32F3G71xx) || defined(WB32FQ95xx)
I2C1_OPMODE,
I2C1_CLOCK_SPEED,
#else
// This configures the I2C clock to 400khz assuming a 72Mhz clock
// For more info : https://www.st.com/en/embedded-software/stsw-stm32126.html
STM32_TIMINGR_PRESC(I2C1_TIMINGR_PRESC) | STM32_TIMINGR_SCLDEL(I2C1_TIMINGR_SCLDEL) | STM32_TIMINGR_SDADEL(I2C1_TIMINGR_SDADEL) | STM32_TIMINGR_SCLH(I2C1_TIMINGR_SCLH) | STM32_TIMINGR_SCLL(I2C1_TIMINGR_SCLL), 0, 0
#endif
};
/**
* @brief Handles any I2C error condition by stopping the I2C peripheral and
* aborting any ongoing transactions. Furthermore ChibiOS status codes are
* converted into QMK codes.
*
* @param status ChibiOS specific I2C status code
* @return i2c_status_t QMK specific I2C status code
*/
static i2c_status_t i2c_epilogue(const msg_t status) {
if (status == MSG_OK) {
return I2C_STATUS_SUCCESS;
}
// From ChibiOS HAL: "After a timeout the driver must be stopped and
// restarted because the bus is in an uncertain state." We also issue that
// hard stop in case of any error.
i2cStop(&I2C_DRIVER);
return status == MSG_TIMEOUT ? I2C_STATUS_TIMEOUT : I2C_STATUS_ERROR;
}
__attribute__((weak)) void i2c_init(void) {
static bool is_initialised = false;
if (!is_initialised) {
is_initialised = true;
// Try releasing special pins for a short time
palSetLineMode(I2C1_SCL_PIN, PAL_MODE_INPUT);
palSetLineMode(I2C1_SDA_PIN, PAL_MODE_INPUT);
chThdSleepMilliseconds(10);
#if defined(USE_GPIOV1)
palSetLineMode(I2C1_SCL_PIN, I2C1_SCL_PAL_MODE);
palSetLineMode(I2C1_SDA_PIN, I2C1_SDA_PAL_MODE);
#else
palSetLineMode(I2C1_SCL_PIN, PAL_MODE_ALTERNATE(I2C1_SCL_PAL_MODE) | PAL_OUTPUT_TYPE_OPENDRAIN);
palSetLineMode(I2C1_SDA_PIN, PAL_MODE_ALTERNATE(I2C1_SDA_PAL_MODE) | PAL_OUTPUT_TYPE_OPENDRAIN);
#endif
}
}
i2c_status_t i2c_transmit(uint8_t address, const uint8_t* data, uint16_t length, uint16_t timeout) {
i2cStart(&I2C_DRIVER, &i2cconfig);
msg_t status = i2cMasterTransmitTimeout(&I2C_DRIVER, (address >> 1), data, length, 0, 0, TIME_MS2I(timeout));
return i2c_epilogue(status);
}
i2c_status_t i2c_receive(uint8_t address, uint8_t* data, uint16_t length, uint16_t timeout) {
i2cStart(&I2C_DRIVER, &i2cconfig);
msg_t status = i2cMasterReceiveTimeout(&I2C_DRIVER, (address >> 1), data, length, TIME_MS2I(timeout));
return i2c_epilogue(status);
}
i2c_status_t i2c_write_register(uint8_t devaddr, uint8_t regaddr, const uint8_t* data, uint16_t length, uint16_t timeout) {
i2cStart(&I2C_DRIVER, &i2cconfig);
uint8_t complete_packet[length + 1];
for (uint16_t i = 0; i < length; i++) {
complete_packet[i + 1] = data[i];
}
complete_packet[0] = regaddr;
msg_t status = i2cMasterTransmitTimeout(&I2C_DRIVER, (devaddr >> 1), complete_packet, length + 1, 0, 0, TIME_MS2I(timeout));
return i2c_epilogue(status);
}
i2c_status_t i2c_write_register16(uint8_t devaddr, uint16_t regaddr, const uint8_t* data, uint16_t length, uint16_t timeout) {
i2cStart(&I2C_DRIVER, &i2cconfig);
uint8_t complete_packet[length + 2];
for (uint16_t i = 0; i < length; i++) {
complete_packet[i + 2] = data[i];
}
complete_packet[0] = regaddr >> 8;
complete_packet[1] = regaddr & 0xFF;
msg_t status = i2cMasterTransmitTimeout(&I2C_DRIVER, (devaddr >> 1), complete_packet, length + 2, 0, 0, TIME_MS2I(timeout));
return i2c_epilogue(status);
}
i2c_status_t i2c_read_register(uint8_t devaddr, uint8_t regaddr, uint8_t* data, uint16_t length, uint16_t timeout) {
i2cStart(&I2C_DRIVER, &i2cconfig);
msg_t status = i2cMasterTransmitTimeout(&I2C_DRIVER, (devaddr >> 1), &regaddr, 1, data, length, TIME_MS2I(timeout));
return i2c_epilogue(status);
}
i2c_status_t i2c_read_register16(uint8_t devaddr, uint16_t regaddr, uint8_t* data, uint16_t length, uint16_t timeout) {
i2cStart(&I2C_DRIVER, &i2cconfig);
uint8_t register_packet[2] = {regaddr >> 8, regaddr & 0xFF};
msg_t status = i2cMasterTransmitTimeout(&I2C_DRIVER, (devaddr >> 1), register_packet, 2, data, length, TIME_MS2I(timeout));
return i2c_epilogue(status);
}
__attribute__((weak)) i2c_status_t i2c_ping_address(uint8_t address, uint16_t timeout) {
// ChibiOS does not provide low level enough control to check for an ack.
// Best effort instead tries reading register 0 which will either succeed or timeout.
// This approach may produce false negative results for I2C devices that do not respond to a register 0 read request.
uint8_t data = 0;
return i2c_readReg(address, 0, &data, sizeof(data), timeout);
}