qmk_firmware/platforms/chibios/mcu_selection.mk
2023-06-28 13:07:14 +10:00

847 lines
23 KiB
Makefile

ifneq ($(findstring MKL26Z64, $(MCU)),)
# Cortex version
MCU = cortex-m0plus
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
ARMV = 6
## chip/board settings
# - the next two should match the directories in
# <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES)
# OR
# <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = KINETIS
MCU_SERIES = KL2x
# Linker script to use
# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
# or <keyboard_dir>/ld/
MCU_LDSCRIPT ?= MKL26Z64
# Startup code to use
# - it should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/
MCU_STARTUP ?= kl2x
# Board: it should exist either in <chibios>/os/hal/boards/,
# <keyboard_dir>/boards/, or drivers/boards/
BOARD ?= PJRC_TEENSY_LC
endif
ifneq ($(findstring MK20DX128, $(MCU)),)
# Cortex version
MCU = cortex-m4
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
ARMV = 7
## chip/board settings
# - the next two should match the directories in
# <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES)
# OR
# <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = KINETIS
MCU_SERIES = K20x
# Linker script to use
# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
# or <keyboard_dir>/ld/
MCU_LDSCRIPT ?= MK20DX128
# Startup code to use
# - it should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/
MCU_STARTUP ?= k20x5
# Board: it should exist either in <chibios>/os/hal/boards/,
# <keyboard_dir>/boards/, or drivers/boards/
BOARD ?= PJRC_TEENSY_3
endif
ifneq ($(findstring MK20DX256, $(MCU)),)
# Cortex version
MCU = cortex-m4
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
ARMV = 7
## chip/board settings
# - the next two should match the directories in
# <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES)
# OR
# <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = KINETIS
MCU_SERIES = K20x
# Linker script to use
# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
# or <keyboard_dir>/ld/
MCU_LDSCRIPT ?= MK20DX256
# Startup code to use
# - it should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/
MCU_STARTUP ?= k20x7
# Board: it should exist either in <chibios>/os/hal/boards/,
# <keyboard_dir>/boards/, or drivers/boards/
BOARD ?= PJRC_TEENSY_3_1
endif
ifneq ($(findstring MK64FX512, $(MCU)),)
# Cortex version
MCU = cortex-m4
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
ARMV = 7
## chip/board settings
# - the next two should match the directories in
# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = KINETIS
MCU_SERIES = K60x
# Linker script to use
# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
# or <keyboard_dir>/ld/
MCU_LDSCRIPT ?= MK64FX512
# Startup code to use
# - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/
MCU_STARTUP ?= k60x
# Board: it should exist either in <chibios>/os/hal/boards/,
# <keyboard_dir>/boards/, or drivers/boards/
BOARD ?= PJRC_TEENSY_3_5
endif
ifneq ($(findstring MK66FX1M0, $(MCU)),)
# Cortex version
MCU = cortex-m4
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
ARMV = 7
## chip/board settings
# - the next two should match the directories in
# <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES)
# OR
# <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = KINETIS
MCU_SERIES = MK66F18
# Linker script to use
# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
# or <keyboard_dir>/ld/
MCU_LDSCRIPT ?= MK66FX1M0
# Startup code to use
# - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/
MCU_STARTUP ?= MK66F18
# Board: it should exist either in <chibios>/os/hal/boards/,
# <keyboard_dir>/boards/, or drivers/boards/
BOARD ?= PJRC_TEENSY_3_6
endif
ifneq ($(findstring RP2040, $(MCU)),)
# Cortex version
MCU = cortex-m0plus
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
CHIBIOS_PORT = ARMv6-M-RP2
## chip/board settings
# - the next two should match the directories in
# <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES)
# OR
# <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = RP
MCU_SERIES = RP2040
# Linker script to use
# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
# or <keyboard_dir>/ld/
STARTUPLD_CONTRIB = $(CHIBIOS_CONTRIB)/os/common/startup/ARMCMx/compilers/GCC/ld
MCU_LDSCRIPT ?= RP2040_FLASH_TIMECRIT
LDFLAGS += -L $(STARTUPLD_CONTRIB)
# Startup code to use
# - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/
MCU_STARTUP ?= rp2040
# Board: it should exist either in <chibios>/os/hal/boards/,
# <keyboard_dir>/boards/, or drivers/boards/
BOARD ?= GENERIC_PROMICRO_RP2040
# Default UF2 Bootloader settings
UF2_FAMILY ?= RP2040
FIRMWARE_FORMAT ?= uf2
endif
ifneq ($(findstring STM32F042, $(MCU)),)
# Cortex version
MCU = cortex-m0
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
ARMV = 6
## chip/board settings
# - the next two should match the directories in
# <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES)
# OR
# <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = STM32
MCU_SERIES = STM32F0xx
# Linker script to use
# - it should exist either in <chibios>/os/common/startup/ARMCMx/compilers/GCC/ld/
# or <keyboard_dir>/ld/
MCU_LDSCRIPT ?= STM32F042x6
# Startup code to use
# - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/
MCU_STARTUP ?= stm32f0xx
# Board: it should exist either in <chibios>/os/hal/boards/,
# <keyboard_dir>/boards/, or drivers/boards/
BOARD ?= GENERIC_STM32_F042X6
USE_FPU ?= no
# UF2 settings
UF2_FAMILY ?= STM32F0
# Stack sizes: Since this chip has limited RAM capacity, the stack area needs to be reduced.
# This ensures that the EEPROM page buffer fits into RAM
USE_PROCESS_STACKSIZE = 0x600
USE_EXCEPTIONS_STACKSIZE = 0x300
# Bootloader address for STM32 DFU
STM32_BOOTLOADER_ADDRESS ?= 0x1FFFC400
endif
ifneq ($(findstring STM32F072, $(MCU)),)
# Cortex version
MCU = cortex-m0
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
ARMV = 6
## chip/board settings
# - the next two should match the directories in
# <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES)
# OR
# <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = STM32
MCU_SERIES = STM32F0xx
# Linker script to use
# - it should exist either in <chibios>/os/common/startup/ARMCMx/compilers/GCC/ld/
# or <keyboard_dir>/ld/
MCU_LDSCRIPT ?= STM32F072xB
# Startup code to use
# - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/
MCU_STARTUP ?= stm32f0xx
# Board: it should exist either in <chibios>/os/hal/boards/,
# <keyboard_dir>/boards/, or drivers/boards/
BOARD ?= GENERIC_STM32_F072XB
USE_FPU ?= no
# UF2 settings
UF2_FAMILY ?= STM32F0
# Bootloader address for STM32 DFU
STM32_BOOTLOADER_ADDRESS ?= 0x1FFFC800
endif
ifneq ($(findstring STM32F103, $(MCU)),)
# Cortex version
MCU = cortex-m3
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
ARMV = 7
## chip/board settings
# - the next two should match the directories in
# <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES)
# OR
# <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = STM32
MCU_SERIES = STM32F1xx
# Linker script to use
# - it should exist either in <chibios>/os/common/startup/ARMCMx/compilers/GCC/ld/
# or <keyboard_dir>/ld/
MCU_LDSCRIPT ?= STM32F103x8
# Startup code to use
# - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/
MCU_STARTUP ?= stm32f1xx
# Board: it should exist either in <chibios>/os/hal/boards/,
# <keyboard_dir>/boards/, or drivers/boards/
BOARD ?= GENERIC_STM32_F103
USE_FPU ?= no
# UF2 settings
UF2_FAMILY ?= STM32F1
endif
ifneq ($(findstring STM32F303, $(MCU)),)
# Cortex version
MCU = cortex-m4
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
ARMV = 7
## chip/board settings
# - the next two should match the directories in
# <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES)
# OR
# <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = STM32
MCU_SERIES = STM32F3xx
# Linker script to use
# - it should exist either in <chibios>/os/common/startup/ARMCMx/compilers/GCC/ld/
# or <keyboard_dir>/ld/
MCU_LDSCRIPT ?= STM32F303xC
# Startup code to use
# - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/
MCU_STARTUP ?= stm32f3xx
# Board: it should exist either in <chibios>/os/hal/boards/,
# <keyboard_dir>/boards/, or drivers/boards/
BOARD ?= GENERIC_STM32_F303XC
USE_FPU ?= yes
# UF2 settings
UF2_FAMILY ?= STM32F3
# Bootloader address for STM32 DFU
STM32_BOOTLOADER_ADDRESS ?= 0x1FFFD800
endif
ifneq ($(findstring STM32F401, $(MCU)),)
# Cortex version
MCU = cortex-m4
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
ARMV = 7
## chip/board settings
# - the next two should match the directories in
# <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES)
# OR
# <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = STM32
MCU_SERIES = STM32F4xx
# Linker script to use
# - it should exist either in <chibios>/os/common/startup/ARMCMx/compilers/GCC/ld/
# or <keyboard_dir>/ld/
MCU_LDSCRIPT ?= STM32F401xC
# Startup code to use
# - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/
MCU_STARTUP ?= stm32f4xx
# Board: it should exist either in <chibios>/os/hal/boards/,
# <keyboard_dir>/boards/, or drivers/boards/
BOARD ?= GENERIC_STM32_F401XC
USE_FPU ?= yes
# UF2 settings
UF2_FAMILY ?= STM32F4
# Bootloader address for STM32 DFU
STM32_BOOTLOADER_ADDRESS ?= 0x1FFF0000
endif
ifneq ($(findstring STM32F405, $(MCU)),)
# Cortex version
MCU = cortex-m4
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
ARMV = 7
## chip/board settings
# - the next two should match the directories in
# <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES)
# OR
# <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = STM32
MCU_SERIES = STM32F4xx
# Linker script to use
# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
# or <keyboard_dir>/ld/
MCU_LDSCRIPT ?= STM32F405xG
# Startup code to use
# - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/
MCU_STARTUP ?= stm32f4xx
# Board: it should exist either in <chibios>/os/hal/boards/,
# <keyboard_dir>/boards/, or drivers/boards/
BOARD ?= GENERIC_STM32_F405XG
USE_FPU ?= yes
# UF2 settings
UF2_FAMILY ?= STM32F4
# Bootloader address for STM32 DFU
STM32_BOOTLOADER_ADDRESS ?= 0x1FFF0000
endif
ifneq ($(findstring STM32F407, $(MCU)),)
# Cortex version
MCU = cortex-m4
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
ARMV = 7
## chip/board settings
# - the next two should match the directories in
# <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES)
# OR
# <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = STM32
MCU_SERIES = STM32F4xx
# Linker script to use
# - it should exist either in <chibios>/os/common/startup/ARMCMx/compilers/GCC/ld/
# or <keyboard_dir>/ld/
MCU_LDSCRIPT ?= STM32F407xE
# Startup code to use
# - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/
MCU_STARTUP ?= stm32f4xx
# Board: it should exist either in <chibios>/os/hal/boards/,
# <keyboard_dir>/boards/, or drivers/boards/
BOARD ?= GENERIC_STM32_F407XE
USE_FPU ?= yes
# UF2 settings
UF2_FAMILY ?= STM32F4
# Bootloader address for STM32 DFU
STM32_BOOTLOADER_ADDRESS ?= 0x1FFF0000
endif
ifneq ($(findstring STM32F411, $(MCU)),)
# Cortex version
MCU = cortex-m4
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
ARMV = 7
## chip/board settings
# - the next two should match the directories in
# <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES)
# OR
# <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = STM32
MCU_SERIES = STM32F4xx
# Linker script to use
# - it should exist either in <chibios>/os/common/startup/ARMCMx/compilers/GCC/ld/
# or <keyboard_dir>/ld/
MCU_LDSCRIPT ?= STM32F411xE
# Startup code to use
# - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/
MCU_STARTUP ?= stm32f4xx
# Board: it should exist either in <chibios>/os/hal/boards/,
# <keyboard_dir>/boards/, or drivers/boards/
BOARD ?= GENERIC_STM32_F411XE
USE_FPU ?= yes
# UF2 settings
UF2_FAMILY ?= STM32F4
# Bootloader address for STM32 DFU
STM32_BOOTLOADER_ADDRESS ?= 0x1FFF0000
endif
ifneq ($(findstring STM32F446, $(MCU)),)
# Cortex version
MCU = cortex-m4
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
ARMV = 7
## chip/board settings
# - the next two should match the directories in
# <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES)
# OR
# <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = STM32
MCU_SERIES = STM32F4xx
# Linker script to use
# - it should exist either in <chibios>/os/common/startup/ARMCMx/compilers/GCC/ld/
# or <keyboard_dir>/ld/
MCU_LDSCRIPT ?= STM32F446xE
# Startup code to use
# - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/
MCU_STARTUP ?= stm32f4xx
# Board: it should exist either in <chibios>/os/hal/boards/,
# <keyboard_dir>/boards/, or drivers/boards/
BOARD ?= GENERIC_STM32_F446XE
USE_FPU ?= yes
# Bootloader address for STM32 DFU
STM32_BOOTLOADER_ADDRESS ?= 0x1FFF0000
# Default as no chibios efl config
EEPROM_DRIVER ?= transient
endif
ifneq ($(findstring STM32G431, $(MCU)),)
# Cortex version
MCU = cortex-m4
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
ARMV = 7
## chip/board settings
# - the next two should match the directories in
# <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES)
# OR
# <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = STM32
MCU_SERIES = STM32G4xx
# Linker script to use
# - it should exist either in <chibios>/os/common/startup/ARMCMx/compilers/GCC/ld/
# or <keyboard_dir>/ld/
MCU_LDSCRIPT ?= STM32G431xB
# Startup code to use
# - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/
MCU_STARTUP ?= stm32g4xx
# Board: it should exist either in <chibios>/os/hal/boards/,
# <keyboard_dir>/boards/, or drivers/boards/
BOARD ?= GENERIC_STM32_G431XB
USE_FPU ?= yes
# UF2 settings
UF2_FAMILY ?= STM32G4
# Bootloader address for STM32 DFU
STM32_BOOTLOADER_ADDRESS ?= 0x1FFF0000
# Default to transient driver as ChibiOS EFL is currently broken for single-bank G4xx devices
EEPROM_DRIVER ?= transient
endif
ifneq ($(findstring STM32G474, $(MCU)),)
# Cortex version
MCU = cortex-m4
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
ARMV = 7
## chip/board settings
# - the next two should match the directories in
# <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES)
# OR
# <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = STM32
MCU_SERIES = STM32G4xx
# Linker script to use
# - it should exist either in <chibios>/os/common/startup/ARMCMx/compilers/GCC/ld/
# or <keyboard_dir>/ld/
MCU_LDSCRIPT ?= STM32G474xE
# Startup code to use
# - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/
MCU_STARTUP ?= stm32g4xx
# Board: it should exist either in <chibios>/os/hal/boards/,
# <keyboard_dir>/boards/, or drivers/boards/
BOARD ?= GENERIC_STM32_G474XE
USE_FPU ?= yes
# UF2 settings
UF2_FAMILY ?= STM32G4
# Bootloader address for STM32 DFU
STM32_BOOTLOADER_ADDRESS ?= 0x1FFF0000
endif
ifneq (,$(filter $(MCU),STM32L432 STM32L442))
# Cortex version
MCU = cortex-m4
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
ARMV = 7
## chip/board settings
# - the next two should match the directories in
# <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES)
# OR
# <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = STM32
MCU_SERIES = STM32L4xx
# Linker script to use
# - it should exist either in <chibios>/os/common/startup/ARMCMx/compilers/GCC/ld/
# or <keyboard_dir>/ld/
MCU_LDSCRIPT ?= STM32L432xC
# Startup code to use
# - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/
MCU_STARTUP ?= stm32l4xx
# Board: it should exist either in <chibios>/os/hal/boards/,
# <keyboard_dir>/boards/, or drivers/boards/
BOARD ?= GENERIC_STM32_L432XC
PLATFORM_NAME ?= platform_l432
USE_FPU ?= yes
# UF2 settings
UF2_FAMILY ?= STM32L4
# Bootloader address for STM32 DFU
STM32_BOOTLOADER_ADDRESS ?= 0x1FFF0000
endif
ifneq (,$(filter $(MCU),STM32L433 STM32L443))
# Cortex version
MCU = cortex-m4
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
ARMV = 7
## chip/board settings
# - the next two should match the directories in
# <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES)
# OR
# <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = STM32
MCU_SERIES = STM32L4xx
# Linker script to use
# - it should exist either in <chibios>/os/common/startup/ARMCMx/compilers/GCC/ld/
# or <keyboard_dir>/ld/
MCU_LDSCRIPT ?= STM32L432xC
# Startup code to use
# - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/
MCU_STARTUP ?= stm32l4xx
# Board: it should exist either in <chibios>/os/hal/boards/,
# <keyboard_dir>/boards/, or drivers/boards/
BOARD ?= GENERIC_STM32_L433XC
PLATFORM_NAME ?= platform_l432
USE_FPU ?= yes
# UF2 settings
UF2_FAMILY ?= STM32L4
# Bootloader address for STM32 DFU
STM32_BOOTLOADER_ADDRESS ?= 0x1FFF0000
endif
ifneq (,$(filter $(MCU),STM32L412 STM32L422))
# Cortex version
MCU = cortex-m4
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
ARMV = 7
## chip/board settings
# - the next two should match the directories in
# <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES)
# OR
# <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = STM32
MCU_SERIES = STM32L4xx
# Linker script to use
# - it should exist either in <chibios>/os/common/startup/ARMCMx/compilers/GCC/ld/
# or <keyboard_dir>/ld/
MCU_LDSCRIPT ?= STM32L412xB
# Startup code to use
# - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/
MCU_STARTUP ?= stm32l4xx
# Board: it should exist either in <chibios>/os/hal/boards/,
# <keyboard_dir>/boards/, or drivers/boards/
BOARD ?= GENERIC_STM32_L412XB
PLATFORM_NAME ?= platform_l412_l422
USE_FPU ?= yes
# UF2 settings
UF2_FAMILY ?= STM32L4
# Bootloader address for STM32 DFU
STM32_BOOTLOADER_ADDRESS ?= 0x1FFF0000
endif
ifneq (,$(filter $(MCU),STM32H723 STM32H733))
# Cortex version
MCU = cortex-m7
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
ARMV = 7
## chip/board settings
# - the next two should match the directories in
# <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES)
# OR
# <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = STM32
MCU_SERIES = STM32H7xx
# Linker script to use
# - it should exist either in <chibios>/os/common/startup/ARMCMx/compilers/GCC/ld/
# or <keyboard_dir>/ld/
MCU_LDSCRIPT ?= STM32H723xG_ITCM64k
# Startup code to use
# - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/
MCU_STARTUP ?= stm32h7xx
# Board: it should exist either in <chibios>/os/hal/boards/,
# <keyboard_dir>/boards/, or drivers/boards/
BOARD ?= GENERIC_STM32_H723XG
PLATFORM_NAME ?= platform_type2
USE_FPU ?= yes
# UF2 settings
UF2_FAMILY ?= STM32H7
# Bootloader address for STM32 DFU
STM32_BOOTLOADER_ADDRESS ?= 0x1FF09800
endif
ifneq ($(findstring WB32F3G71, $(MCU)),)
# Cortex version
MCU = cortex-m3
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
ARMV = 7
## chip/board settings
# - the next two should match the directories in
# <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES)
# OR
# <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = WB32
MCU_SERIES = WB32F3G71xx
# Linker script to use
# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
# or <keyboard_dir>/ld/
MCU_LDSCRIPT ?= WB32F3G71x9
# Startup code to use
# - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/
MCU_STARTUP ?= wb32f3g71xx
# Board: it should exist either in <chibios>/os/hal/boards/,
# <keyboard_dir>/boards/, or drivers/boards/
BOARD ?= GENERIC_WB32_F3G71XX
USE_FPU ?= no
# Bootloader address for WB32 DFU
WB32_BOOTLOADER_ADDRESS ?= 0x1FFFE000
endif
ifneq ($(findstring WB32FQ95, $(MCU)),)
# Cortex version
MCU = cortex-m3
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
ARMV = 7
## chip/board settings
# - the next two should match the directories in
# <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES)
# OR
# <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = WB32
MCU_SERIES = WB32FQ95xx
# Linker script to use
# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
# or <keyboard_dir>/ld/
MCU_LDSCRIPT ?= WB32FQ95xB
# Startup code to use
# - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/
MCU_STARTUP ?= wb32fq95xx
# Board: it should exist either in <chibios>/os/hal/boards/,
# <keyboard_dir>/boards/, or drivers/boards/
BOARD ?= GENERIC_WB32_FQ95XX
USE_FPU ?= no
# Bootloader address for WB32 DFU
WB32_BOOTLOADER_ADDRESS ?= 0x1FFFE000
endif
ifneq ($(findstring GD32VF103, $(MCU)),)
# RISC-V
MCU = risc-v
# RISC-V extensions and abi configuration
MCU_ARCH = rv32imac
MCU_ABI = ilp32
MCU_CMODEL = medlow
## chip/board settings
# - the next two should match the directories in
# <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES)
# OR
# <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_PORT_NAME = GD
MCU_FAMILY = GD32V
MCU_SERIES = GD32VF103
# Linker script to use
# - it should exist either in <chibios>/os/common/startup/RISCV-ECLIC/compilers/GCC/ld/
# or <keyboard_dir>/ld/
MCU_LDSCRIPT ?= GD32VF103xB
# Startup code to use
# - it should exist in <chibios>/os/common/startup/RISCV-ECLIC/compilers/GCC/mk/
MCU_STARTUP ?= gd32vf103
# Board: it should exist either in <chibios>/os/hal/boards/,
# <keyboard_dir>/boards/, or drivers/boards/
BOARD ?= SIPEED_LONGAN_NANO
USE_FPU ?= no
endif