* Add support for hardware and board initialisation overrides.
* qmk cformat.
* Add some documentation.
* Docs clarity.
* Make early_hardware_init_pre a no-op for now, until migrations occur.
* Doco update
* Make distinction between keyboard and ChibiOS board in docs
* Doc anchors.
* Update tmk_core/protocol/chibios/main.c
Co-Authored-By: Joel Challis <git@zvecr.com>
* Rework bootloader entry to be off by default, allow opting-in.
Co-authored-by: Joel Challis <git@zvecr.com>
* Add PS2_MOUSE_ROTATE to compensate for device orientation
* fixup! Add PS2_MOUSE_ROTATE to compensate for device orientation
* Reformat with IndentPPDirectives: AfterHash as per #6316
* Change _delay_ms/us() to wait_ms/us()
* Switch to platform-agnostic GPIO macros
* Add AVR spi_master and migrate Adafruit BLE code
* Set verbose back to false
* Add clock divisor, bit order and SPI mode configuration for init
* Add start and stop functions
* Move configuration of mode, endianness and speed to `spi_start()`
* Some breaks here would be good
* Default Adafruit BLE clock divisor to 4 (2MHz on the Feather 32U4)
* Remove mode and divisor enums
* Add some docs
* No hr at EOF
* Add links in sidebar
* rewrite usbhid feature on vusb
* Apply suggestions from code review
Co-Authored-By: Ryan <fauxpark@gmail.com>
* fix typo
* fix typo again
* Update tmk_core/protocol/vusb/vusb.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* clean up defines
Co-authored-by: Ryan <fauxpark@gmail.com>
* Port over some AVR backlight logic to SLEEP_LED
* Port over some AVR backlight logic to SLEEP_LED - add timer 3
* Port over some AVR backlight logic to SLEEP_LED - clang format
* Enable SLEEP_LED within vusb protocol
* Add support for RAW endpoint for arm_atsam
This the excellent work from helluvamatt/qmk_firmware in bb6eeb93b.
* Reformat arm_atsam RAW endpoint code
Co-authored-by: Matt Schneeberger <helluvamatt@gmail.com>
* Remove unnecessary import of rgblight.h in tmk_core/protocol/*/*.c
* tmk_core/protocol/chibios/main.c
* tmk_core/protocol/lufa/lufa.c
see #8380 for tmk_core/protocol/vusb/main.c.
* Remove '#include "rgblight.h"' from tmk_core/protocol/vusb/main.c.
* Moved contents of rgblight_reconfig.h to rgblight_post_config.h.
In #3582, rgblight_reconfig.h had to be newly created. Now, the build system of qmk_firmware has a post_cofig feature, so that what was done in rgblight_reconfig.h can now be realized in rgblight_post_config.h.
**This commit does not change the build result.**
Testing script
```shell
# build on master
git checkout master
echo master > /tmp/master_md5.txt
# RGBLIGHT_ENABLE = no
make HELIX=verbose helix/rev2:default:clean
make HELIX=verbose helix/rev2:default
md5 helix_rev2_default.hex >> /tmp/master_md5.txt
# RGBLIGHT_ENABLE = yes, with animations
make HELIX=verbose helix/rev2/back:default:clean
make HELIX=verbose helix/rev2/back:default
md5 helix_rev2_back_default.hex >> /tmp/master_md5.txt
# RGBLIGHT_ENABLE = yes, without animations
make HELIX=verbose,no_ani helix/rev2/back:default:clean
make HELIX=verbose,no_ani helix/rev2/back:default
md5 helix_rev2_back_default.hex >> /tmp/master_md5.txt
# build on refactor_rgblight_reconfig.h
git checkout refactor_rgblight_reconfig.h
echo refactor_rgblight_reconfig.h > /tmp/branch_md5.txt
# RGBLIGHT_ENABLE = no
make HELIX=verbose helix/rev2:default:clean
make HELIX=verbose helix/rev2:default
md5 helix_rev2_default.hex >> /tmp/branch_md5.txt
# RGBLIGHT_ENABLE = yes, with animations
make HELIX=verbose helix/rev2/back:default:clean
make HELIX=verbose helix/rev2/back:default
md5 helix_rev2_back_default.hex >> /tmp/branch_md5.txt
# RGBLIGHT_ENABLE = yes, without animations
make HELIX=verbose,no_ani helix/rev2/back:default:clean
make HELIX=verbose,no_ani helix/rev2/back:default
md5 helix_rev2_back_default.hex >> /tmp/branch_md5.txt
diff -u /tmp/master_md5.txt /tmp/branch_md5.txt
```
Test result:
```
--- /tmp/master_md5.txt 2020-01-03 15:42:22.000000000 +0900
+++ /tmp/branch_md5.txt 2020-01-03 15:42:42.000000000 +0900
@@ -1,4 +1,4 @@
-master
+refactor_rgblight_reconfig.h
MD5 (helix_rev2_default.hex) = f360032edd522448366d471d8f4f8181
MD5 (helix_rev2_back_default.hex) = 0c663acc6cccc44476b3b969ad22a48f
MD5 (helix_rev2_back_default.hex) = e66b1195ff6d38e6e22c975b8ae42fd3
```
* Expressions that are too long are difficult to read, so wrap them.
* Edit the expression again
* remove `defined(RGBLIGHT_ANIMATIONS)` in `tmk_core/common/*/suspend.c`, `tmk_core/protocol/*/main.c`
move contents of rgblight_reconfig.h to rgblight.h.
The following changes were made to rgblight.h.
```diff
+#ifdef RGBLIGHT_USE_TIMER
void rgblight_task(void);
void rgblight_timer_init(void);
void rgblight_timer_enable(void);
void rgblight_timer_disable(void);
void rgblight_timer_toggle(void);
+#else
+#define rgblight_task()
+#define rgblight_timer_init()
+#define rgblight_timer_enable()
+#define rgblight_timer_disable()
+#define rgblight_timer_toggle()
+#endif
```
The following changes were made to tmk_core/common/avr/suspend.c, tmk_core/common/chibios/suspend.c, tmk_core/protocol/chibios/main.c, tmk_core/protocol/lufa/lufa.c, tmk_core/protocol/vusb/main.c.
```diff
-# ifdef RGBLIGHT_ANIMATIONS
rgblight_timer_enable();
-# endif
```
```diff
-#if defined(RGBLIGHT_ANIMATIONS) && defined(RGBLIGHT_ENABLE)
+#if defined(RGBLIGHT_ENABLE)
rgblight_task();
#endif
```
* remove 'defined(RGBLIGHT_ANIMATIONS)' in tmk_core/common/keyboard.c
Co-authored-by: Joel Challis <git@zvecr.com>
* Dedupe extrakey report struct, and send functions in V-USB & LUFA
* Doc comment for consistency
* Wrap it in ifdef to prevent unused function error
* Do the same for ATSAM
* Align endpoint config as per rest of file (fixes#4783)
* Add comments about explicit order use
* Update tmk_core/protocol/chibios/usb_main.c
Co-Authored-By: fauxpark <fauxpark@gmail.com>
* Initial ARM bitbang ws2812 driver
* Unify chibios platform to run rgblight_task
* Remove 'avr only' comments from ws2812 docs
* Remove 'avr only' comments from ws2812 docs
* Unify chibios platform to run rgblight_task - review comments
* Remove debug flags from keymap
* Add comments from review
* Add defines for STM32L0XX
* Attempt to get arm ws2812 working on multiple gcc versions
* Fix battery level code in adafruit_ble.cpp
The code in tsk_core/protocol/lufa/adafluit_ble.cpp that polls the
battery level for the Adafruit feather BLE controller reads the
regulated voltage, not the raw voltage coming from the battery. To do
that, the Adafruit Feather docs say you should read from pin A9:
https://learn.adafruit.com/adafruit-feather-32u4-basic-proto/power-management#measuring-battery-4-9.
(See also
https://learn.adafruit.com/adafruit-feather-32u4-bluefruit-le/pinouts#logic-pins-2-9.)
I'm not sure why, but analogRead(9); doesn't read the correct pin.
Checking all available analog pins experimentally, it turns out that
analogRead(7); returns the correct value. So the code above should read:
state.vbat = analogRead(7);
* Update tmk_core/protocol/lufa/adafruit_ble.cpp
Co-Authored-By: Drashna Jaelre <drashna@live.com>
* Remove old comment
* Fix linking error
* Remove `#ifdef` around `#include analog.h`.
* Really fix linking error
* Fix indentation
* Fix braces
* Expand descriptor headers
* Align descriptor elements
* Nicer formatting
* Tidy up preprocessor statements
* Remove VERSION_BCD redefine - LUFA_VERSION_INTEGER is currently 0x170418
* Tidy up comments
* Tweak ordering of HID report elements (no functional changes)
* We don't need all of these newlines
* Move default USB_MAX_POWER_CONSUMPTION closer to where it makes sense
* Ask nicely
* Add some more comments
* Change indentation back to 4 spaces
* Add changelog entry
* clean up rgb matrix extern usage
Moved rgb matrix boiler plate into macros
Rebased onto typing heatmap pr
* Fixing the reversed frame buffer access in digital rain
* Fixing digital rain & typing heatmap if keyreactive effects are not enabled
* Apply suggestions from code review
Co-Authored-By: Drashna Jaelre <drashna@live.com>
* Adding parenthesizes to DRIVER_LED_TOTAL where necessary
* Updated docs
* added notes about parentheses
* Initial conversion of the rgb_led struct
* Converting last keyboard & updating effects to take advantage of the new structure
* New struct should not be const
* Updated docs
* Changing define ___ for no led to NO_LED
* Missed converting some keymap usages of the old struct layout
Assuming I understand this correctly, this should set the max scancode to E7 (RGUI), which is the last listed code in the main list (everything else use for internal QMK/TMK stuff).
* port Massdrop CTRL/ALT to use RGB Matrix
Co-authored-by: Matt Schneeberger <helluvamatt@gmail.com>
* Massdrop lighting support working
This commit is to get the Massdrop lighting code working again through use of the compilation define USE_MASSDROP_CONFIGURATOR added to a keymap's rules.mk.
Added keymaps for both CTRL and ALT named default_md and mac_md. These should be used if the Massdrop style lighting is desired.
* Updating config based on testing results with patrickmt & compile errors
* Updates for PR5328
For CTRL and ALT:
Moved location of new RGB Matrix macros from config_led.h to config.h.
Added RGB_MATRIX_LED_FLUSH_LIMIT (time between flushes) to config.h for correct LED driver update timing.
Re-added missing breathing code for when Massdrop configurator mode is defined.
* remove prilik keymap form PR
* Add suspend functions
* Disable RGB code if it's disabled
* Add keyboard_init functions
* Change where references so it will compile
* Wrong command chained in wake up kb function
* Fix non-feature file changes
* Add documentation
* Re-add matrix init docs
* add rgblight code to example
* Remove suspend code
* Clean up docs
* Fix docs
* Fix suspend code
* more doc fixes
* change function to startup_* rather than keyboard_init_
* fix spelling error
* fix up docs to finish removing keyboard_init
* Use Pre and Post init functions
* Update Documenation
* Remove changes to my keymap and userspace code
* Cleanup
* Revert changes to extra files
* Forgot a semicolon
* Make sure all protocols call keyboard_setup
* Cleanup functions
* Unset startup_user
* Remove changes from division keyboard
* Readd startup_user function
* Remove all to startup_user
* Update docs/custom_quantum_functions.md
Co-Authored-By: drashna <drashna@live.com>
* Update docs/custom_quantum_functions.md
Co-Authored-By: drashna <drashna@live.com>
* Add suggestion line
* Rebase fixes
* Update documentation to be more useful/accurate
* Cleanup of documentation
* Fix spacing inconsistency
* Revert unexpected change to keymap
* Remove unnecessary IS_COMMAND definition in clueboard/66/rev4
* Replace keyboard_report->mods with get_mods() in IS_COMMAND definitions
* Update docs to use get_mods() instead of keyboard_report->mods
* Replace keyboard_report->mods with get_mods() in tmk_core/protocol/usb_hid/test
For some reason, this occurrence used KB_LSHIFT and KB_RSHIFT, which don't exist
* Replace keyboard_report->mods with get_mods() in Massdrop keyboards (as per @patrickmt)
* Add ability to animate arm_atsam led matrix from the center of a circle
* Make arm_atsam led matrix circular animation circular rather than obloid
* Fix indentation in tmk_core led_matrix.c
When this if statement is false, it will cause the report ID to be read as the LED state.
We already know there are two bytes in the endpoint, which is a reasonably good indicator that it contains a report ID, so we should always read both.
* Check the size of the SET_REPORT packet
If we have two bytes, that probably means the first is a report ID. The 6KRO interface may or may not have one, but the NKRO interface always does, so we need to check this regardless of whether KEYBOARD_SHARED_EP is defined.
* Fix indentation
Microsecond (us) delays are now handled by a busy wait loop according to MCU frequency. This replaces the system counter method which had an overhead of around 12us.
TC5 device and supporting routines removed as it was the old us delay counter.
wait_ms is now properly a macro to CLK_delay_ms.
wait_us is now properly a macro to CLK_delay_us.
Removed CLK_get_us as it has no use.
All calls to CLK_get_ms() have been replaced by timer_read64() with corrected typing.
All calls to CLK_delay_ms() have been replaced by wait_ms().
All calls to CLK_delay_us() have been replaced by wait_us() and timings verified or updated as needed after review on scope.
Corrected typing of variables using 64bit ms timer readings if needed.
* initial commit, this now mostly works
- RGB controls work
- Dynamic keymap still broken due to eeprom
- Via works
* STM32 eeprom update
- Update EEPROM emulation library to handle 8bit data like AVR.
- This library also allows for multiple page pairs resulting in greater EEPROM size flexibility
* hs60 changes
* HS60 hhkb added
* Update keyboards/hs60/v2/config.h
Co-Authored-By: yiancar <yiangosyiangou@cytanet.com.cy>
MCU Pins for debugging, LED, boot tracing, and shift registers are now configurable at keyboard level.
Macros led_* replaced by DBG_LED_*
Macros m15_* replaced by DBG_1_*
Macros m27_* replaced by DBG_2_*
Macros m28_* replaced by DBG_3_*
For CTRL and ALT keyboards, debug boot tracing pin default now set to pad M27 instead of M28 since although M28 is not being used, it is technically a signal for USB port detection.
m15_print(...) renamed to dbg_print(...) to get away from hard coded port names.
dbg_print function now follows similar pattern to debug led output.
* Add initial support for vertically-oriented animations
* DRY up vertical animation support
* Fix animation code for arm_atsam led_matrix to work in all directions
* Adjust py calculation to base off bottom rather than top
* Unify multiple HID interfaces into one
This reduces the number of USB endpoints required, which frees them up
for other things.
NKRO and EXTRAKEY always use the shared endpoint.
By default, MOUSEKEY also uses it. This means it won't work as a Boot
Procotol mouse in some BIOSes, etc. If you really think your
keyboard needs to work as a mouse in your BIOS, set
MOUSE_SHARED_EP = no in your rules.mk.
By default, the core keyboard does not use the shared endpoint, as not
all BIOSes are standards compliant and that's one place you don't want
to find out your keyboard doesn't work.. If you are really confident,
you can set KEYBOARD_SHARED_EP = yes to use the shared endpoint here
too.
* unify endpoints: ChibiOS protocol implementation
* fixup: missing #ifdef EXTRAKEY_ENABLEs
broke build on AVR with EXTRAKEY disabled
* endpoints: restore error when too many endpoints required
* lufa: wait up to 10ms to send keyboard input
This avoids packets being dropped when two reports are sent in quick
succession (eg. releasing a dual role key).
* endpoints: fix compile on ARM_ATSAM
* endpoint: ARM_ATSAM fixes
No longer use wrong or unexpected endpoint IDs
* endpoints: accommodate VUSB protocol
V-USB has its own, understandably simple ideas about the report formats.
It already blasts the mouse and extrakeys through one endpoint with
report IDs. We just stay out of its way.
* endpoints: document new endpoint configuration options
* endpoints: respect keyboard_report->mods in NKRO
The caller(s) of host_keyboard_send expect to be able to just drop
modifiers in the mods field and not worry about whether NKRO is in use.
This is a good thing. So we just shift it over if needs be.
* endpoints: report.c: update for new keyboard_report format
Rewrote USB state tracking for implementation of suspend state.
Updated suspend.c in entirety.
Main subtasks (generally hardware related) are now run prior to keyboard task.
* add computed pins from mcu type
* update for atmega32a
* doc typo
* add atmega16 chips, link to references
* remove avr include from config
* exclude assembler in config.h includes
* consolodate options, add 646
* fix typo in pindef
* Converter: add XT USB converter from TMK
* Converter: port TMK code for USB converter to QMK
* Apply requested changes after code review by @drashna
- use "pragma once" instead of include guards
- use LAYOUT instead of KEYMAP
- allow customisation with matrix_init_user() and matrix_scan_user()
- set BOOTLOADER instead of BOOTLOADER_SIZE
- Add XT_ENABLE to OPT_DEFS
* Remove unnecessary lines
Added hid_listen USB device for arm_atsam USB protocol.
Debug printing is now done through the console device (CONSOLE_ENABLE = yes) rather than the virtser device, for viewing in hid_listen.
Function dpf(...) renamed to CDC_printf(...) and should now be called directly if intending to print to the virtual serial device.
* Update for SEND_STRING usage
Update for SEND_STRING usage.
Sending keyboard reports (kbd, nkro) now obey the minimum polling time.
While attempting to send a keyboard report and waiting for a USB poll, other functions of the keyboard, including LED effects and power management, will continue to operate at their intended intervals.
* Updates for send string, syscalls, stdio, debug prints, auto shift
Now properly waiting for previous keys sent over USB to complete before sending new.
Added heap to linker and now compiling with syscalls support.
Removed custom string functions and now using stdio.
dprintf now works as intended through virtser device.
* CTRL and ALT keymap updates
CTRL mac keymap updated
ALT default and mac keymap updated
ALT rules.mk added Auto Shift with default no
* Code cleanup as per discussion with vomindoraan
Code cleanup as per discussion with vomindoraan
* add temporary test code rgblight-macro-test1.[ch]
* rgblight.h : mode auto numberring and auto generate mode name symbol
No change in build result.
* rgblight.c use RGBLIGHT_MODE_xxx symbols
No change in build result.
* quantum.c use RGBLIGHT_MODE_xxx symbols
No change in build result.
* fix build break. when RGB_MATRIX_ENABLE defined
* add temporary test code rgblight-macro-test2.[ch]
* modify rgblight_mode_eeprom_helper() and rgblight_sethsv_eeprom_helper()
* modify rgblight_task()
* configurable each effect compile on/off in config.h
* update docs/feature_rgblight.md
* fix conflict. docs/feature_rgblight.md
* remove temporary test code rgblight-macro-test*.[ch]
* fix comment typo.
* remove old mode number from comment
* update docs/feature_rgblight.md about effect mode
* Revert "update docs/feature_rgblight.md about effect mode"
This reverts commit 43890663fcc9dda1899df7a37d382fc38b1a6d6d.
* some change docs/feature_rgblight.md
* fix typo
* docs/feature_rgblight.md update: revise mode number table
* ALT keymap update
Added additional End key on layer 1 to match key cap
* LED driver update addressing PR #3871
Update sync between IS31FL3733 drivers is causing varying behavior in keyboards including brightness mismatch and slight flicker at very low rgb values. Visually, disabling sync is not noticeable. Ref PR #3871 by guarnacciaa.
Added support to enter bootloader from software (bootloader version must be newer than "v2.18Jun 22 2018 17:28:08" until workaround for older is created).
Updated CTRL and ALT keymaps for entering bootloader with Fn+b held for >500ms.
Added basic MacOS keymap for ALT.
USB sleep LED indicator now turns off after 1 second.
Slowed down debug LED code printing.
- Added support for NO_USB_STARTUP_CHECK. This allows the keyboard do function and not get stuck in a SUSPENDED state loop in case of no USB connection.
- Added support for WAIT_FOR_USB. In LUFA no keyboard has this flag enable therefor no keyboard waits for usb to be active.
- Added documentation for both configuration flags as they were missing.
Renamed keyboard alt67 to alt and adjusted necessary files where alt67 appeared.
CTRL keymap fixed enum structure name.
usb2422 removed stray define no longer used.
* STM32 EEPROM Emulation
- Added EEPROM emulation libaries from libmaple and Arduino_STM32. https://github.com/rogerclarkmelbourne/Arduino_STM32 and https://github.com/leaflabs/libmaple.
- Renamed teensy EEPROM library and added conditional selection of library.
- Remapped EEPROM memory map for 16 byte blocks (as is with STM32f3xx MCUs).
- Added EEPROM initialization in main.c of Chibios.
- Added EEPROM format to clear the emulated pages when EEPROM is marked as invalid.
* Fixed ifdef
* Massdrop SAMD51
Massdrop SAMD51 keyboards initial project upload
* Removing relocated files
Removing files that were relocated and not deleted from previous location
* LED queue fix and cleaning
Cleaned some white space or comments.
Fix for LED I2C command queue.
Cleaned up interrupts.
Added debug function for printing numbers to scope through m15 line.
* Factory programmed serial usage
Ability to use factory programmed serial in hub and keyboard usb descriptors
* USB serial number and bugfix
Added support for factory programmed serial and usage.
Incorporated bootloader's conditional compiling to align project closer.
Fixed issue when USB device attempted to send before enabled.
General white space and comment cleanup.
* Project cleanup
Cleaned up project in terms of white space, commented code, and unecessary files.
NKRO keyboard is now using correct setreport although KBD was fine to use.
Fixed broken linkage to __xprintf for serial debug statements.
* Fix for extra keys
Fixed possible USB hang on extra keys report set missing
* I2C cleanup
I2C cleanup and file renames necessary for master branch merge
* Boot tracing and clocks cleanup
Added optional boot debug trace mode through debug LED codes.
General clock code cleanup.
* Relocate ARM/Atmel headers
Moved ARM/Atmel header folder from drivers to lib and made necessary makefile changes.
* Pull request changes
Pull request changes
* Keymap and compile flag fix
Keymap fix for momentary layer.
Potential compile flag fix for Travis CI failure.
* va_list include fix
Fix for va_list compile failure
* Include file case fixes
Fixes for include files with incorrect case
* ctrl and alt67 keyboard readme
Added ctrl and alt67 keyboard readme files
* initial files for rev 6 with encoder
* music map init, dip scan added
* adds ws2812 driver for arm
* flesh out dip and encoder support
* adds default encoder res
* adds default encoder res
* start muse implementation
* muse working with encoder as control
* flip direction
* try mouse wheel again
* dont break other revs
* dont break other revs
* conditional autio
* pwm ws driver (not working)
* update build includes for chibios
* update ws2812 driver/config
* last commit for glasser code
* working example
* remove rgb for now
* finish up rev6
* working encoder keycodes
* add warnings to planck keymaps about the LAYOUT
* Copy Chibios serial_usb_driver into the chibios/protocol
It's renamed to usb_driver to avoid name conflicts
* Make the usb driver compile
* Disable ChibiOS serial usb driver for all keyboards
* Change usb_main to use QMKUSBDriver
* Initialize the usb driver buffers
* Add support for fixed size queues
* Fix USB driver initialization
* Don't transfer an empty packet for fixed size streams
* Generate api docs from source code
* Add a bunch of doxygen comments
* more doxygen comments
* Add the in-progress api docs
* script to generate docs from travis
* Add doc generation to the travis job
* make travis_docs.sh commit the work it does
* make sure the docs script exits cleanly
* Move lufa descriptor to protocol/usb_descriptor
* Try to compile usb_descriptor on ChibiOS
* Add lufa_utils for ChibiOS
Lufa USB descriptors for ChibiOS
* More lufa_util compatibility fixes
* First compiling version of shared USB descriptor
* Send the usb descriptors
* Fix the CONSOLE output on ChibiOS
* Add errors for unsupported interfaces
* Enable support for vitual serial port USB descriptors
* Implement virtual serial port for ChibiOS
* Cleanup the lufa_utils
Use the default lufa header files
* Add raw hid support for ChibiOS
This is completely untested
* Enable midi compilation on ChibiOS
* Move midi functionality out of lufa.c
* Don't register sysex callback when not needed
* ChibiOS compilation fixes
* Update ChibiOS submodule
* Fix the Midi USB descriptor
It didn't work properly when both Midi and Virtual serial port was enabled.
* Add MIDI support for ChibiOS
* Fix USB descriptor strings on ChibiOS
* Use serial usb driver for raw hid
* Generalize the ChibiOS stream like drivers
This makes the initialization much more simple and eliminates a lot of
the code duplication.
* Convert console output to chibios stream driver
* Fixes for ChibiOS update
* Update the ChibiOS contrib submodule
To include the usb data toggle synchronization fixes
* Fix duplicate reset enumeration on ChibiOS
* Add missing include
* Add number of endpoints check for ChibiOS
* Enable serial USB driver on all keyboards
* Add missing includes when API is enabled withot midi
* Add another missing inlcude
* Add NIU Mini keymap from Planck keymap
* Remove old keymap files
* Fix README, removed Planck references
* Add default layout, move Planck layout to separate folder
* Update README
* Add my XD60 keymap
* Change RShift to slash
* Fix keymap: stuck on MO(1)
* Move RESET to Fn+Enter
* Add: RGB saturation cycle
* Add numpad layer to keymap
* Fix last case
* Cleanup Mechmini keymap. Once the custom RGB function is defined, there is no need to manually handle RGB code.
* Change default to KEYMAP_MIT, not KEYMAP_OFFSET
* Add custom RGB code for JJ40
* Reset Mechmini advertised power draw to 500. Will have to test actual maximum power draw later.
* RGB working on JJ40.
* Fix: saturation increase/decrease flipped
* Add new directory for my custom keymap with RGB keycodes
* Swap LAlt and LGUI
* Update JJ40 max power draw with measured value
* Update: fun40 rules.mk to enable underglow; earlier failed Travis CI
* Fix: init RGB LEDs on boot. Also added HHKB-like keymap for XD60.
* Super rudimentary backlight test, init RGB LEDs on boot
* Backlighting works - stays on for now
* Toggling working
* Now can override backlight.c functions. Problem was functions in backlight.c weren't called before due to a lack of matrix_scan_quantum() in matrix.c
* Timers not working
* Delete global.h
* Cleanup
* Compiles
* Good sign: LEDs stop working again
* Handle timer1 overflow
* Progress: fix: forgot to init
* Backlighting fully working now except breathing.
* Revert keymap to original keycodes
* Update XD60 keymap README
* Update JJ40 keymap with backlight toggles
* Breathing working just fine.
* Update references
* Add backlight_set() call
* Cleanup code to disable backlight
* Fix: does not compile
* Fix: missing call to rgblight_task.
* Testing with BACKLIGHT_BREATHING
* Cleanup
* Cleanup comments
* More commenting cleanup.
* Do not enable BACKLIGHT_BREATHING by default
* Update XD60 keymap
* Update: move matrix_scan_kb out from matrix.c to jj40.c (kb-level)
* Cleanup for PR
* Fix conflict in readme.md for NIU mini
* Restore original power consumption figure
* Fix: matrix_scan_user() now has to be defined in the keymaps
* Add weak `matrix_scan_user` so it does not have to be defined in keymap
* Add weak matrix_init_user()
* initial clueboard_60 support
* LED lighting support
* fix the clueboard->clueboard_66 rename
* Add layout support to clueboard_60
* Fix the 60_iso layout so it's actually iso
* add a default keymap for AEK layout
* fix clueboard_17
* Fixup the ISO layouts
* Fix the `wait_ms()/wait_us()` definitions for chibios
* Fix up the wait_ms/wait_us hack. Reduce stack size.
* Add a missing #include "wait.h"
* commit files that should have already been comitted
Refactored Bluetooth support to make adding new Bluetooth modules
easier in the future.
* Remove `OUT_BLE` key from QMK's keymap. `OUT_BT` is all we need now
as there's no difference anymore.
* Made BLUETOOTH_ENABLE build option legacy as not to break existing
keymaps (Falls back to existing EZ Key support if on)
* Removed `ADAFRUIT_BLE_ENABLE` build option
* Created new build option `BLUETOOTH` with module option (Currently
`AdafruitEZKey` & `AdafruitBLE`)
* Moved all LUFA bluetooth key/mouse events under `BLUETOOTH_ENABLE`
ifdef with selected modules output.
Fix memory leaks by using stack instead of malloc
Reduce memory usage by having less temporary bufffers
Remove warnings by adding includes
Decrease code size by 608 bytes (mostly due to not linking malloc)
More robust handling of buffer overflows
There are a lot of PS/2 commands, some are vendor/device specific, so we
provide a weak ps2_mouse_init_user() to be implemented in each keyboard
that need it.
There are now 3 potential locations to send HID reports:
1. USB
2. The bluefruit easy key
3. Adafruit BLE
Generally speaking, if USB is connected then we should prefer to
send the reports there; it is generally the best channel for this.
The bluefruit module has no feedback about bluetooth connectivity
so the code must speculatively send reports over both USB and bluetooth.
The BLE module has connectivity feedback. In general we want to
prefer to send HID reports over USB while connected there, even
if BLE is connected. Except that it is convenient to force them
over BLE while testing the implementation.
This policy has been extracted out into a where_to_send function
which returns a bitmask of which of the channels should be used.
This implements some helper functions that allow sending key reports
to an SPI based Bluetooth Low Energy module, such as the Adafruit
Feather 32u4 Bluefruit LE.
There is some plumbing required in lufa.c to enable this; that
is in a follow-on commit.
Modified the LUFA USB HID Descriptor to change the logical/usage
minimums for System Control from 0x01 (Mouse) to 0x81 (System Power
Down), this fixes OS X recognizing the Planck as having a mouse and
tablet, even with mousekeys off.
* Modularity and gcc warnings fixes.
* Add ChibiOS support (USB stack + support files).
* Make usb_main more USB_DRIVER #define independent.
* Move chibios to tool.
* Implement jump-to-bootloader.
* Small updates.
* Fix bootloader-jump compiling.
* Move AVR specific sleep_led.c into avr.
* Add basic sleep_led for chibios.
* Update chibios README.
* NKRO fixes.
* Rename some Makefile defines.
* Move STM32 bootloader address config to separate .h file.
* Add ARM Teensies bootloader code.
* Fix chibios/usb_main GET_REPORT handing.
* Add missing #include to keymap.c.
* Make bootmagic.c code portable (_delay_ms -> wait_ms).
* Move declaration of keymap_config.
Should really not declare variables in .h files - since it's included
in different .c files, a proper linker then complains that the same
variable is declared more than once (once for each .c file that the
offending .h is included in).
* Add eeprom support for chibios/kinetis.
* Rename chibios example keyboard.
* Move chibios/cortex selection to local Makefiles.
* Chibios: use WFI in idle. WIP suspend stuff.
* ChibiOS/kinetis: sending remote wakeup.
* ChibiOS/STM32: send remote wakeup.
* Fix report size of boot protocol.
* Fix drop key stroke
Keyboard report should be checked if its transfer finishs successfully.
Otherwise key stroke can be missing when other key event occurs
before the last report transfer is done.
Boot protocol 10ms interval probably causes this problem in case
it receives key events in a row within the period. NKRO protocol
suffers less or nothing due to its interval 1ms.
* Chibios/usb_main: rename a variable for clarity.
* Add correct chibios/bootloader_jump for infinity KB.
* ChibiOS: make reset request more CMSISy.
* Chibios: Add breathing sleep LED on Kinetis MCUs.
* ChibiOS: Update infinity bootloader code to match updated ChibiOS.
* ChibiOS: prettify/document sleep_led code.
* Chibios: Remove the wait in the main loop.
* Add maple mini code.
* Do timeout when writing to CONSOLE EP queue.
Fixes TMK bug #266.
* Chibios: add 'core/protocol' to the makefiles' search path.
* Chibios: Update to new USB API.
* Chibios: add more guards for transmitting (fix a deadlock bug).
* Add update for chibios in README
* Chibios: Fix a HardFault bug (wait after start).
* Chibios: cleanup usb_main code.
* Chibios: Revert common.mk change (fix AVR linking problem).
* core: Fix chibios user compile options
Compile options can be defined in project Makefile such as UDEFS, UADEFS, UINCDIR, ULIBDIR and ULIBS.
* Sysv format for ChibiOS arm-none-eabi-size
Some new patches to ChibiOS puts heap as it's own section. So the
berkeley format is now useless, as the heap will be included in the
BSS report. The sysv format displays the bss size correctly.
* Fix hard-coded path of CHIBIOS
* Add support for new version of ChibiOS and Contrib
The Kinetis support has moved to a separate Contrib repository in
the newest version of Chibios. There has also been some structure
changes. So this adds support for those, while maintaining back-
wards compability.
* Update ChibiOS instructions
* Chibios: implement sleep LED for STM32.
* Chibios: Update the main chibios README.
* Chibios: fix STM32_BOOTLOADER_ADDRESS name.
* Chibios: make the default bootloader_jump redefinable (weak).
* Chibios: disable LTO (link-time optimisation).
With LTO enabled, sometimes things fail for mysterious reasons
(e.g. bootloader jump on WF with LEDs enabled), just because the
linker optimisation is too aggressive.
* Chibios: add default location for chibios-contrib.
* ChibiOS: update mk to match chibios/master.
* ChibiOS: update instructions.md.
* Add chibi_onekey example.
* Add comments to chibi_onekey Makefile.
* Rename some Makefile defines.
* Move STM32 bootloader address config to separate .h file.
* Rename chibios example keyboard.
* Move chibios/cortex selection to local Makefiles.
* Add Teensy LC onekey example.
* Chibios: use WFI in idle. WIP suspend stuff.
* Update chibi/teensy instructions.
* Update chibios/Teensy instructions.
* Add infinity_chibios
* Add keymap_hasu.c
* Infinity_chibios: select correct bootloader_jump.
* Infinity_chibios: improve comments.
* Add generic STM32F103C8T6 example.
* Add maple mini code.
* STM32F103x fixes.
* Add maple mini pinout pic.
* Chibios: updates for 3.0.4 git.
* Chibios: rename example stm32_onekey -> stm32_f072_onekey.
* Chibios: add makefiles for Teensy 3.x examples.
* Chibios: update Teensy 3.x instructions.
* Chibios: Tsy LC is cortex-m0plus.
* Chibios: add more guards for transmitting (fix a deadlock bug).
* Change README for chibios
* Chibios: update examples to current chibios git.
Match the changes in mainline chibios:
- update chconf.h
- update supplied ld scripts structure
- update Teensy instructions (switch to official
chibios and introduce contrib)
* Add ChibiOS and ChibiOS-Contrib submodules
Also fix the makefile path for them.
* Moves chibios keyboards to keyboards folder
* First version of ChibiOS compilation
Only the stm32_f072_onkey keyboard is ported at the moment. It
compiles, but still doesn't link.
* More chibios fixes
It now compiles without warnings and links
* Move the teensy_lc_onekey to the keyboards folder
* Clean up the make file rule structure
* Remove keymap_fn_to_action
* Update more ChibiOS keyboards to QMK
Most of them does not compile at the moment though.
* Use older version of Chibios libraries
The newest ones have problems with compilation
* Remove USB_UNCONFIGURED event
It isn't present in the older version of ChibiOS
* Fix the infinity_chibios compilation
* Fix potentially uninitialized variable
* Add missing include
* Fix the ChibiOS makefile
* Fix some Chibios keyboard compilation
* Revert the rules.mk file back to master version
* Combine the chibios and AVR makefiles
With just the required overrides in the respective platform
specific one.
* Slight makefile restrucuring
Platform specific compiler options
* Move avr specific targets out of the main rules
* Fix ChibiOS objcopy
The ChibiOS objcopy needs different parameters, so the parameters
are moved to the corresponding platform rule file
* Fix the objcopy for real this time
The comands were moved around, so chibios used avr and the ohter
way around.
Also change the objsize output format
* Fix the thumb flags
* Fix the infinity hasu keymap
* Per platform cpp flags
* Add gcc-arm-none-eabi package to travis
* Add arm-none-eabi-newlib to travis
* Fix the name of the libnewlib-arm-none-eabi lib
* Fix the ChibiOS paths
So that they are properly relative, and builds don't generate
extra folders
* Fix the board path of stm32_f103_onekey
* Only consider folders with Makefiles as subproject
