* Add Per Key functionality for AutoShift (#11536)
* LED Matrix: Reactive effect buffers & advanced indicators (#12588)
* [Keyboard] kint36: switch to sym_eager_pk debouncing (#12626)
* [Keyboard] kint2pp: reduce input latency by ≈10ms (#12625)
* LED Matrix: Split (#12633)
* [CI] Format code according to conventions (#12650)
* feat: infinite timeout for leader key (#6580)
* feat: implement leader_no_timeout logic
* docs(leader_key): infinite leader timeout docs
* Format code according to conventions (#12680)
* Update ADC driver for STM32F1xx, STM32F3xx, STM32F4xx (#12403)
* Fix default ADC_RESOLUTION for ADCv3 (and ADCv4)
Recent ChibiOS update removed ADC_CFGR1_RES_10BIT from the ADCv3 headers
(that macro should not have been there, because ADCv3 has CFGR instead of
CFGR1). Fix the default value for ADC_RESOLUTION to use ADC_CFGR_RES_10BITS
if it is defined (that name is used for ADCv3 and ADCv4).
* Update ADC docs to match the actually used resolution
ADC driver for ChibiOS actually uses the 10-bit resolution by default
(probably to match AVR); fix the documentation accordingly. Also add
both ADC_CFGR_RES_10BITS and ADC_CFGR1_RES_10BIT constants (these names
differ according to the ADC implementation in the particular MCU).
* Fix pinToMux() for B12 and B13 on STM32F3xx
Testing on STM32F303CCT6 revealed that the ADC mux values for B12 and
B13 pins were wrong.
* Add support for all possible analog pins on STM32F1xx
Added ADC mux values for pins A0...A7, B0, B1, C0...C5 on STM32F1xx
(they are the same at least for STM32F103x8 and larger F103 devices, and
also F102, F105, F107 families). Actually tested on STM32F103C8T6
(therefore pins C0...C5 were not tested).
Pins F6...F10, which are present on STM32F103x[C-G] in 144-pin packages,
cannot be supported at the moment, because those pins are connected only
to ADC3, but the ChibiOS ADC driver for STM32F1xx supports only ADC1.
* Add support for all possible analog pins on STM32F4xx
Added ADC mux values for pins A0...A7, B0, B1, C0...C5 and optionally
F3...F10 (if STM32_ADC_USE_ADC3 is enabled). These mux values are
apparently the same for all F4xx devices, except some smaller devices may
not have ADC3.
Actually tested on STM32F401CCU6, STM32F401CEU6, STM32F411CEU6 (using
various WeAct “Blackpill” boards); only pins A0...A7, B0, B1 were tested.
Pins F3...F10 are inside `#if STM32_ADC_USE_ADC3` because some devices
which don't have ADC3 also don't have the GPIOF port, therefore the code
which refers to Fx pins does not compile.
* Fix STM32F3xx ADC mux table in documentation
The ADC driver documentation had some errors in the mux table for STM32F3xx.
Fix this table to match the datasheet and the actual code (mux settings for
B12 and B13 were also tested on a real STM32F303CCT6 chip).
* Add STM32F1xx ADC pins to the documentation
* Add STM32F4xx ADC pins to the documentation
* Add initial support for tinyuf2 bootloader (when hosted on F411 blackpill) (#12600)
* Add support for jumping to tinyuf2 bootloader. Adds blackpill UF2 example.
* Update flashing.md
* Update chconf.h
* Update config.h
* Update halconf.h
* Update mcuconf.h
* eeprom driver: Refactor where eeprom driver initialisation (and EEPROM emulation initialisation) occurs to make it non-target-specific. (#12671)
* Add support for MCU = STM32F446 (#12619)
* Add support for MCU = STM32F446
* Update platforms/chibios/GENERIC_STM32_F446XE/configs/config.h
* Restore mcuconf.h to the one used by RT-STM32F446RE-NUCLEO64
* stm32f446: update mcuconf.h and board.h for 16MHz operation, with USB enabled, and other peripherals disabled.
* Format code according to conventions (#12682)
* Format code according to conventions (#12687)
* Add STM32L433 and L443 support (#12063)
* initial L433 commit
* change to XC
* fix L433
* disable all peripherals
* update system and peripheral clocks
* 433 change
* use its own board files
* revert its own board files
* l433 specific change
* fix stm32l432xx define
* remove duplicate #define
* fix bootloader jump
* move to L443xx and add i2c2, spi2, usart3 to mcuconf.h
* move to L443
* move to L443
* fix sdmmc in mcuconf.h
* include STM32L443
* add L443
* Include L443 in compatible microcontrollers
* Include L443 in compatible microcontrollers
* Update config bootloader jump description
* Update ChibiOS define reasoning
* Update quantum/mcu_selection.mk
* fix git conflict
* Updated Function96 with V2 files and removed chconf.h and halconf.h (#12613)
* Fix bad PR merge for #6580. (#12721)
* Change RGB/LED Matrix to use a simple define for USB suspend (#12697)
* [CI] Format code according to conventions (#12731)
* Fixing transport's led/rgb matrix suspend state logic (#12770)
* [CI] Format code according to conventions (#12772)
* Fix comment parsing (#12750)
* Added OLED fade out support (#12086)
* fix some references to bin/qmk that slipped in (#12832)
* Resolve a number of warnings in `qmk generate-api` (#12833)
* New command: qmk console (#12828)
* stash poc
* stash
* tidy up implementation
* Tidy up slightly for review
* Tidy up slightly for review
* Bodge environment to make tests pass
* Refactor away from asyncio due to windows issues
* Filter devices
* align vid/pid printing
* Add hidapi to the installers
* start preparing for multiple hid_listeners
* udev rules for hid_listen
* refactor to move closer to end state
* very basic implementation of the threaded model
* refactor how vid/pid/index are supplied and parsed
* windows improvements
* read the report directly when usage page isn't available
* add per-device colors, the choice to show names or numbers, and refactor
* add timestamps
* Add support for showing bootloaders
* tweak the color for bootloaders
* Align bootloader disconnect with connect color
* add support for showing all bootloaders
* fix the pyusb check
* tweaks
* fix exception
* hide a stack trace behind -v
* add --no-bootloaders option
* add documentation for qmk console
* Apply suggestions from code review
* pyformat
* clean up and flesh out KNOWN_BOOTLOADERS
* Remove pointless SERIAL_LINK_ENABLE rules (#12846)
* Make Swap Hands use PROGMEM (#12284)
This converts the array that the Swap Hands feature uses to use PROGMEM,
and to read from that array, as such. Since this array never changes at
runtime, there is no reason to keep it in memory. Especially for AVR
boards, as memory is a precious resource.
* Fix another bin/qmk reference (#12856)
* [Keymap] Turn OLED off on suspend in soundmonster keymap (#10419)
* Fixup build errors on `develop` branch. (#12723)
* LED Matrix: Effects! (#12651)
* Fix syntax error when compiling for ARM (#12866)
* Remove KEYMAP and LAYOUT_kc (#12160)
* alias KEYMAP to LAYOUT
* remove KEYMAP and LAYOUT_kc
* Add setup, clone, and env to the list of commands we allow even with broken modules (#12868)
* Rename `point_t` -> `led_point_t` (#12864)
* [Keyboard] updated a vendor name / fixed minor keymap issues (#12881)
* Add missing LED Matrix suspend code to suspend.c (#12878)
* LED Matrix: Documentation (#12685)
* Deprecate `send_unicode_hex_string()` (#12602)
* Fix spelling mistake regarding LED Matrix in split_common. (#12888)
* [Keymap] Fix QWERTY/DVORAK status output for kzar keymap (#12895)
* Use milc.subcommand.config instead of qmk.cli.config (#12915)
* Use milc.subcommand.config instead
* pyformat
* remove the config test
* Add function to allow repeated blinking of one layer (#12237)
* Implement function rgblight_blink_layer_repeat to allow repeated blinking of one layer at a time
* Update doc
* Rework rgblight blinking according to requested change
* optimize storage
* Fixup housekeeping from being invoked twice per loop. (#12933)
* matrix: wait for row signal to go HIGH for every row (#12945)
I noticed this discrepancy (last row of the matrix treated differently than the
others) when optimizing the input latency of my keyboard controller, see also
https://michael.stapelberg.ch/posts/2021-05-08-keyboard-input-latency-qmk-kinesis/
Before this commit, when tuning the delays I noticed ghost key presses when
pressing the F2 key, which is on the last row of the keyboard matrix: the
dead_grave key, which is on the first row of the keyboard matrix, would be
incorrectly detected as pressed.
After this commit, all keyboard matrix rows are interpreted correctly.
I suspect that my setup is more susceptible to this nuance than others because I
use GPIO_INPUT_PIN_DELAY=0 and hence don’t have another delay that might mask
the problem.
* ensure we do not conflict with existing keymap aliases (#12976)
* Add support for up to 4 IS31FL3733 drivers (#12342)
* Convert Encoder callbacks to be boolean functions (#12805)
* [Keyboard] Fix Terrazzo build failure (#12977)
* Do not hard set config in CPTC files (#11864)
* [Keyboard] Corne - Remove legacy revision support (#12226)
* [Keymap] Update to Drashna keymap and user code (based on develop) (#12936)
* Add Full-duplex serial driver for ARM boards (#9842)
* Document LED_MATRIX_FRAMEBUFFER_EFFECTS (#12987)
* Backlight: add defines for default level and breathing state (#12560)
* Add dire message about LUFA mass storage bootloader (#13014)
* [Keyboard] Remove redundant legacy and common headers for crkbd (#13023)
Was causing compiler errors on some systems.
* Fix keyboards/keymaps for boolean encoder callback changes (#12985)
* `backlight.c`: include `eeprom.h` (#13024)
* Add changelog for 2021-05-29 Breaking Changes merge (#12939)
* Add ChangeLog for 2021-05-29 Breaking Changes Merge: initial version
* Add recent develop changes
* Sort recent develop changes
* Remove sections for ChibiOS changes per tzarc
No ChibiOS changes this round.
* Add and sort recent develop changes
* add notes about keyboard moves/deletions
* import changelog for PR 12172
Documents the change to BOOTMAGIC_ENABLE.
* update section headings
* re-sort changelog
* add additional note regarding Bootmagic changes
* remove changelog timestamp
* update dates in main Breaking Changes docs
* fix broken section anchors in previous changelogs
* add link to backlight/eeprom patch to changelog
* highlight some more changes
* link PRs from section headers
* Restore standard readme
* run: qmk cformat --core-only
* Change _delay_ms/us() to wait_ms/us()
* Switch to platform-agnostic GPIO macros
* Add AVR spi_master and migrate Adafruit BLE code
* Set verbose back to false
* Add clock divisor, bit order and SPI mode configuration for init
* Add start and stop functions
* Move configuration of mode, endianness and speed to `spi_start()`
* Some breaks here would be good
* Default Adafruit BLE clock divisor to 4 (2MHz on the Feather 32U4)
* Remove mode and divisor enums
* Add some docs
* No hr at EOF
* Add links in sidebar
* Fix battery level code in adafruit_ble.cpp
The code in tsk_core/protocol/lufa/adafluit_ble.cpp that polls the
battery level for the Adafruit feather BLE controller reads the
regulated voltage, not the raw voltage coming from the battery. To do
that, the Adafruit Feather docs say you should read from pin A9:
https://learn.adafruit.com/adafruit-feather-32u4-basic-proto/power-management#measuring-battery-4-9.
(See also
https://learn.adafruit.com/adafruit-feather-32u4-bluefruit-le/pinouts#logic-pins-2-9.)
I'm not sure why, but analogRead(9); doesn't read the correct pin.
Checking all available analog pins experimentally, it turns out that
analogRead(7); returns the correct value. So the code above should read:
state.vbat = analogRead(7);
* Update tmk_core/protocol/lufa/adafruit_ble.cpp
Co-Authored-By: Drashna Jaelre <drashna@live.com>
* Remove old comment
* Fix linking error
* Remove `#ifdef` around `#include analog.h`.
* Really fix linking error
* Move lufa descriptor to protocol/usb_descriptor
* Try to compile usb_descriptor on ChibiOS
* Add lufa_utils for ChibiOS
Lufa USB descriptors for ChibiOS
* More lufa_util compatibility fixes
* First compiling version of shared USB descriptor
* Send the usb descriptors
* Fix the CONSOLE output on ChibiOS
* Add errors for unsupported interfaces
* Enable support for vitual serial port USB descriptors
* Implement virtual serial port for ChibiOS
* Cleanup the lufa_utils
Use the default lufa header files
* Add raw hid support for ChibiOS
This is completely untested
* Enable midi compilation on ChibiOS
* Move midi functionality out of lufa.c
* Don't register sysex callback when not needed
* ChibiOS compilation fixes
* Update ChibiOS submodule
* Fix the Midi USB descriptor
It didn't work properly when both Midi and Virtual serial port was enabled.
* Add MIDI support for ChibiOS
* Fix USB descriptor strings on ChibiOS
* Use serial usb driver for raw hid
* Generalize the ChibiOS stream like drivers
This makes the initialization much more simple and eliminates a lot of
the code duplication.
* Convert console output to chibios stream driver
* Fixes for ChibiOS update
* Update the ChibiOS contrib submodule
To include the usb data toggle synchronization fixes
* Fix duplicate reset enumeration on ChibiOS
* Add missing include
* Add number of endpoints check for ChibiOS
* Enable serial USB driver on all keyboards
* Add missing includes when API is enabled withot midi
* Add another missing inlcude
Refactored Bluetooth support to make adding new Bluetooth modules
easier in the future.
* Remove `OUT_BLE` key from QMK's keymap. `OUT_BT` is all we need now
as there's no difference anymore.
* Made BLUETOOTH_ENABLE build option legacy as not to break existing
keymaps (Falls back to existing EZ Key support if on)
* Removed `ADAFRUIT_BLE_ENABLE` build option
* Created new build option `BLUETOOTH` with module option (Currently
`AdafruitEZKey` & `AdafruitBLE`)
* Moved all LUFA bluetooth key/mouse events under `BLUETOOTH_ENABLE`
ifdef with selected modules output.
This implements some helper functions that allow sending key reports
to an SPI based Bluetooth Low Energy module, such as the Adafruit
Feather 32u4 Bluefruit LE.
There is some plumbing required in lufa.c to enable this; that
is in a follow-on commit.
* .build containment implemented
* no destructive variable setting - builds in either folder
* make from 3 places
* cleans before each build
* make from root with keyboard=keyboard, keymap=keymap
* make from keyboard/keyboard with keymap=keymap
* make from keymaps/keymap
* only implemented on planck
* adds color diag to avr-gcc
* makefiles for all plancks, clean-up
* quick build-all makefile for plancks
* reformatting of make output (colors)
* color toggle, tmk path corrections
* correct if statement for color
* move config.h to main makefile, updates preonic, atomic
* format update, all keyboards targets
* makefile optional for build all target, alps and arrow_pad updated
* alps updated
* make planck default, trying out travis recipe for all-keyboards
* all-keymaps target, different travis recipe
* updates alps64
* updates keyboards to new format
* updates clue* projects
* all projects updated, specialise EZ .hex, let .hex through
* updates travis
* automatically find root, keyboard, keymap
* silent echo, cleaned-up mass make output
* updates all keyboards' .hex files except EZ
* Rename Bantam44.c to bantam44.c
* Rename Bantam44.h to bantam44.h
* nananana
* adds six key keyboard
* does same to ez as rest
* updates send_string example
* brings ergodox_ez up to date
* updates template/new project script
* adds sixkeyboard
* adds readme for sixkeyboard
* adds sixkeyboard to travis
* filenames, gitignore mess
* define clock prescaler stuff manually
* make quick, size test example
* documentation and dfu-no-build
