* solenoid: remove two functions that do nothing.
These functions modify the argument, and so they do nothing.
Note: versions of these functions exist in mtdjr's user folder,
however to core solenoid support and mtdjr user-specific solenoid
support are exclusive (only one can be used at a time).
So removing these confusing functions does no harm.
* solenoid: bugfix: don't allow dwell time to go 1ms below minimum time.
The previous code allowed dwell time to go 1ms below the configured minimum.
This change corrects it.
* solenoid: bugfix: when incrementing above maximum dwell time, jump back to minimum, not to 1
The previous code used to jump back to 1, which might be way under the configured minimum setting.
* solenoid: bugfix: on startup actually use the eeprom-stored dwell-time
This is because the dwell time is stored in two variables.
* solenoid: bugfix: on haptic_reset, actually use the newly set default dwell time.
This is needed because dwell time is configured in two variables.
* solenoid: on HPT_RST set buzz to a default value
* solenoid: buzz: reworked to make more configurable. Previous behaviour maintained.
* solenoid: documentation: clarify meaning of dwell time
* solenoid: add feature SOLENOID_DWELL_STEP_SIZE
* solenoid: documentation: added note about the precision of the solenoid time settings
* haptic: Correctly call haptic_reset when eeprom is corrupt.
* haptic: improve what happens if haptic is enabled without erasing eeprom
* haptic: improve what happens if solenoid is enabled without erasing eeprom
* drivers/haptic: fix compilation issue, when haptic is enabled, but solenoid isn't
* Fix dirtying in oled_write_pixel()
Set the dirty bit for the block only if oled_write_pixel() actually
changed the buffer state. Without this check oled_write_pixel() could
not be used inside the oled_task_user() code using the “redraw always”
style, because the blocks touched by oled_write_pixel() would always
appear dirty, and oled_render() would not proceed beyond the first such
dirty block.
* Fix oled_write_pixel() with 90/270 degree rotation
Use oled_rotation_width instead of OLED_DISPLAY_WIDTH, so that a rotated
display would be handled correctly.
* Fix compilation with custom OLED_BLOCK_COUNT and OLED_BLOCK_SIZE
Some OLED sizes (e.g., 64×48) may require a nonstandard value of
OLED_BLOCK_COUNT. The documentation says that this value may be
redefined in config.h, but actually trying to redefine it caused a
compile error, because the macro was redefined in oled_driver.c.
Make the OLED_BLOCK_COUNT definition in oled_driver.c respect any
user override, and do the same for OLED_BLOCK_SIZE just in case.
* Fix handling of out-of-range bits in oled_dirty
If a custom OLED_BLOCK_COUNT value is specified, some bits in oled_dirty
may not correspond to existing blocks; however, if those bits are set
somewhere (e.g., by code with sets oled_dirty to ~0 or even -1),
oled_render() would try to handle them and could access memory beyond
oled_buffer and perform hardware operations with out of range values.
Prevent this by masking off unused bits in oled_render(), and also avoid
setting those bits in other functions.
* Fix potentially wrong dirtying in oled_write_char()
oled_write_char() tried to mark the position just beyond the written
character as dirty; use (OLED_FONT_WIDTH - 1) to dirty the last position
still belonging to the character instead.
* Fix `#define OLED_BLOCK_TYPE uint32_t` on AVR
Using uint32_t as OLED_BLOCK_TYPE did not work properly on AVR, because
some bit shifts were performed using 16-bit int. Add explicit casts to
OLED_BLOCK_TYPE to those shifts.
* Fix issue with data transfer of CS1_SW7 to CS18_SW7.
* Fix issue with handling of scaling register buffer's dirty flag.
* Remove unused extern declaration.
* Compaction of struct is31_led utilizing bit fields.
* [Driver] bugfix reset the scaling register flag to FALSE
* Update drivers/issi/is31fl3741.c
Co-authored-by: Ryan <fauxpark@gmail.com>
* Add CS & SW defines for ISSI3741
* Make IS31FL3741 control register update clearer
Co-authored-by: Ryan <fauxpark@gmail.com>
Co-authored-by: Jumail Mundekkat <mundekkat@hotmail.com>
Some STM32 chips have STM32_DMA1_STREAM1 as the first DMA stream, others
(F4xx, F7xx, H7xx) have STM32_DMA1_STREAM0. Instead of those names, use
STM32_DMA_STREAM(0), which should always give the first stm32_dma_stream_t
structure in the DMA streams array, so that the stream ID would be
calculated correctly.
* add support for hid gamepad interface
add documentation for HID joystick
Add joystick_task to read analog axes values even when no key is pressed or release. update doc
Update docs/feature_joystick.md
Manage pin setup and read to maintain matrix scan after analog read
* Incorporates patches and changes to HID reporting
There are some patches provided by @a-chol incorporated on this commit,
and also some changes I made to the HID Report structure.
The most interesting is the one dealing with number of buttons: Linux
doesn't seem to care, but Windows requires the HID structure to be byte
aligned (that's in the spec). So if one declares 8/16/32... buttons they
should not have any issues, but this is what happens when you have 9
buttons:
```
bits |0|1|2|3|4|5|6|7|
|*|*|*|*|*|*|*|*| axis 0 (report size 8)
|*|*|*|*|*|*|*|*| ...
|*|*|*|*|*|*|*|*|
|*|*|*|*|*|*|*|*|
|*|*|*|*|*|*|*|*|
|*|*|*|*|*|*|*|*|
|*|*|*|*|*|*|*|*| axis 6
|*|*|*|*|*|*|*|*| first 8 buttons (report size 1)
|*| | | | | | | | last of 9 buttons, not aligned
```
So for that I added a conditonal that will add a number of reports with
size 1 to make sure it aligns to the next multiple of 8. Those reports
send dummy inputs that don't do anything aside from aligning the data.
Tested on Linux, Windows 10 and Street Fighter (where the joystick is
recognized as direct-input)
* Add save and restore of each pin used in reading joystick (AVR).
Allow output pin to be JS_VIRTUAL_AXIS if the axis is connected to Vcc
instead of an output pin from the MCU.
Fix joystick report id
Fix broken v-usb hid joystick interface. Make it more resilient to unusual settings (none multiple of eight button count, 0 buttons or 0 axes)
Correct adc reading for multiple axes. Piecewise range conversion for uncentered raw value range. Input, output and ground pin configuration per axis.
Documentation fixes
* Fix port addressing for joystick analog read
* The other required set of changes
As per the PR, the changes still holding it up.
Add onekey for testing.
Fix ARM builds.
Fix device descriptor when either axes or buttons is zero.
Add compile-time check for at least one axis or button.
Move definition to try to fix conflict.
PR review comments.
qmk cformat
* avoid float functions to compute range mapping for axis adc reading
* Remove V-USB support for now. Updated docs accordingly.
* Update tmk_core/protocol/lufa/lufa.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Update tmk_core/protocol/usb_descriptor.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Update tmk_core/protocol/usb_descriptor.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Update tmk_core/protocol/usb_descriptor.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Add support for joystick adc reading for stm32 MCUs. Fix joystick hid report sending for chibios
* Fix HID joystick report sending for ChibiOS.
Add one analog axis to the onekey:joystick keymap.
Fix pin state save and restore during joystick analog read for STM32
MCUs.
* Update tmk_core/protocol/chibios/usb_main.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Update tmk_core/protocol/lufa/lufa.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Add missing mcuconf.h and halconf.h to onekey:joystick keymap.
Add suggested fixes from PR.
* Switch saveState and restoreState signature to use pin_t type.
onekey:joystick : add a second axis, virtual and programmatically animated.
* Update docs/feature_joystick.md
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Update docs/feature_joystick.md
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Add PR corrections
* Remove halconf.h and mcuconf.h from onekey keymaps
* Change ADC_PIN to A0
Co-authored-by: achol <allecooll@hotmail.com>
Co-authored-by: José Júnior <jose.junior@gmail.com>
Co-authored-by: a-chol <achol@notamail.com>
Co-authored-by: Nick Brassel <nick@tzarc.org>
Co-authored-by: Ryan <fauxpark@gmail.com>
* Initial work for consolidation of board files and default ChibiOS configs.
* Migrate F401/F411 black pills for testing.
* Add early init bootloader jump flag.
* Add support for I2C in order to use i2c_scanner keymap.
* Add F401/F411 HSE bypass to get things booting.
* Exempt "hooked" ChibiOS conf files from updater script.
* Fix up ordering for bootloader_defs file check.
* Match previous $(KEYBOARD_PATHS) value for Proton-C, updated for all board configs.
* I2C_TIMEOUT is not defined on arm teensy
* Work round teensy having different ChibiOS config options
* Stash OLED conf files
* update comment
* update comment
* Remove stm32 alias to allow teensy alt mode
* Add a function to set individual pixels
* Add documentation for oled_write_pixel
* use smaller data type for oled_write_pixel
* Fix boundary check edge case
* Update oled_write_pixel doc
Co-authored-by: Ryan <fauxpark@gmail.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
* Fix incorrect delay when setting WS2812 (and similar) leds
* Add documentation for WS2812_DELAY_MICROSECONDS
* Remove improper cast to uint8_t
Co-authored-by: Sergey Vlasov <sigprof@gmail.com>
* Remove unneeded cast to uint8_t and correct math
Co-authored-by: Sergey Vlasov <sigprof@gmail.com>
* microseconds -> µs
Co-authored-by: Ryan <fauxpark@gmail.com>
* Make documentation better match the spec sheet.
Co-authored-by: Ryan <fauxpark@gmail.com>
* Rename macro to match spec sheet
* Further correction to the delay maths for the SPI case.
Co-authored-by: Joel Challis <git@zvecr.com>
* Move ws2812_common.h to the drivers directory
* Revert "Further correction to the delay maths for the SPI case."
This reverts commit e61b56a2cfc7dfec9992a7a3af92afa50e5b8ec0.
* Remove ws2812_setleds_pin(); consolidate ws2812.h
Co-authored-by: Sergey Vlasov <sigprof@gmail.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
Co-authored-by: Joel Challis <git@zvecr.com>
* ARM split - Add uart half duplex transport support
* Fix for f103
* initial full duplex pass
* partially remove full duplex
* Correct speeds within driver docs
Co-authored-by: Nick Brassel <nick@tzarc.org>
Co-authored-by: Nick Brassel <nick@tzarc.org>
* Change _delay_ms/us() to wait_ms/us()
* Switch to platform-agnostic GPIO macros
* Add AVR spi_master and migrate Adafruit BLE code
* Set verbose back to false
* Add clock divisor, bit order and SPI mode configuration for init
* Add start and stop functions
* Move configuration of mode, endianness and speed to `spi_start()`
* Some breaks here would be good
* Default Adafruit BLE clock divisor to 4 (2MHz on the Feather 32U4)
* Remove mode and divisor enums
* Add some docs
* No hr at EOF
* Add links in sidebar
* Update tmk_core/common/progmem.h
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Update quantum/rgblight.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* fixed problem with implicit declaration in quantum/rgblight.c (#8381)
Co-authored-by: Ryan <fauxpark@gmail.com>
* Update switch to array to allow custom values
* Add adc keymap
* update docs to reflect alignment of default 10 bit
* start conversion to USE_ADCVn
* samplerate is hella wrong...stub out for now
* basic f1 and f4 functionality
* Tidy up current changes
* Restore old pinToMux function
* Add back sample rate for supported platforms
* F0 compile fixes
* wordsmithery
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Remove reference to avr only function
Co-authored-by: Ryan <fauxpark@gmail.com>
