* Make solo half of split keyboards (more) usable.
Using only one half of a split keyboard (that's using the split_common
framework to communicate) is not a great experience, since several read
timeouts per scan cycle cause an unusably slow scan rate.
This change blocks all split communication attempts for 500 ms
(configurable) after an error occurs, causing the scan rate to become at
least _more_ usable, but might need some tweaking to work fully on most
keyboards. One read timeout still needs to occur after the 500 ms has
passed, and if that timeout isn't low enough, some scan cycles may still
be too slow.
* Fix lint complaint.
* Require 25 consecutive comm errors to see comms as disconnected.
The number of max errors can be overridden by defining
`SPLIT_MAX_CONNECTION_ERRORS`.
* Add comments to new defines, and ability to disable disconnection check.
Also increase `SPLIT_MAX_CONNECTION_ERRORS` to 40, since it's divisible
by most relevant numbers for the description.
* Make lint happy ...again
* Only update `connection_check_timer` when needed.
* Add new defines to split keyboard documentation.
* Move connection timeout logic to transport.c, add `is_transport_connected`.
* Use split_common disconnection logic in matrix.c.
Instead of doing more or less the same thing twice.
* Move disconnection logic to `transport_master`.
Is a cleaner implementation, and causes the scan rate while disconnected
to increase instead of decrease.
* Lint fixes.
* Lower default `SERIAL_USART_TIMEOUT` to 20 ms.
The read timeout must be low enough to not cause exessively long scan
cycles when using a solo split half. 10 ms was determined from testing
to work fine even with the slowest defined baudrate of 19200 (5 ms was
too low for that case), so 20 ms should be fine for most cases.
* Remove `SERIAL_USART_TIMEOUT` from ergodox_infinity/config.h
Was somewhat mistakenly included in an earlier PR.
* Fix building with `USE_I2C`.
* Reduce built firmware size.
Not really sure why this works, the idea was taken from tzarc's work on
split disconnection.
* Tweak and improve opt-out for split disconnection logic.
There are now two ways to opt out from this feature:
* Set `SPLIT_MAX_CONNECTION_ERRORS` to 0. This will completely disable
the connection status checks (also affects the slave matrix reset logic in
matrix.c, though).
* Set `SPLIT_CONNECTION_CHECK_TIMEOUT` to 0. This will only disable the
communication throttling while disconnected. Will make the firmware
smaller.
* Make split disconnection logic work with custom transports.
Includes a fallback implementation for keyboards using a custom
split_util.c but not a custom matrix.c (currently no such keyboard seems
to be merged, though).
* Remove unnecessary include of timer.h
Co-authored-by: Joel Challis <git@zvecr.com>
Co-authored-by: Joel Challis <git@zvecr.com>
* Fill the oleds with right mods
* Enable double mods on x32 oleds
* Disable forced NKRO
* Make oleds fancy only on good MCUs
* Overhaul oled display
* Further enhance oled, with kitty!
* Final oled form
* Not working transport
* Transport id of woring
* Add acceleration
* fix button placement for accel macro
* Fix accelartion location and behavior
* Remove OLED sync code
* Fix alignment issue
* Remove audio hack
* Fix up zima keymap
* Add matrix slave scan function and cleanup drashna.h
* Clean up user space
* Allow userspace sync to be disable-able
* Fix weird issue with audio
* Fix alignment issue with user split sync
* Disable second rgb matrix task
* Disable additional animations
* Change dynamic keymap settings
* Hacky fix for borked corne
* Add Blackpill (F411) support to tractyl manuform
* remove manual via eeprom reset
* Remove all references to rgblight twinkle
* Fix issues with config processing
* Support using a timer for wait_us() on ChibiOS-based boards (#12198)
There are spare GPT timers that can be used to get a more accurate
wait_ms() time. This is required for the matrix scan unselect delay (30µs)
to be shorter than the system tick rate of 100µs.
This is limited to the maximum GPT duration of 65535 so values above that
will automatically use the previous implementation based on the system
tick.
Using a specific timer means it can't be shared by another thread at the
same time so when wait_us() is called from anything other than the main
thread it will use the system tick implementation too.
* Update tmk_core/common/chibios/wait.c
* Update tmk_core/common/chibios/wait.c
Co-authored-by: Joel Challis <git@zvecr.com>
* rename LAYOUT to LAYOUT_all
* add info.json
* override DYNAMIC_KEYMAP_LAYER_COUNT for via keymap
The via keymap only initialized two layers without overriding the default value of DYNAMIC_KEYMAP_LAYER_COUNT (4).
This commit sets DYNAMIC_KEYMAP_LAYER_COUNT for the via keymap to 2.
