af1b22f300
There are also some duplication on getting HW watchpoint/breakpoint registers info between GDB and GDBserver. This patch moves them to nat/aarch64-linux-hw-point.c. Note that ENABLE_NLS is not defined in GDBserver, so it should be OK to use _( markup. gdb: 2015-07-21 Yao Qi <yao.qi@linaro.org> * aarch64-linux-nat.c (aarch64_linux_get_debug_reg_capacity): Move it to nat/aarch64-linux-hw-point.c. (aarch64_linux_child_post_startup_inferior): Update. * nat/aarch64-linux-hw-point.c (aarch64_linux_get_debug_reg_capacity): New function. * nat/aarch64-linux-hw-point.h (aarch64_linux_get_debug_reg_capacity): Declare it. gdb/gdbserver: 2015-07-21 Yao Qi <yao.qi@linaro.org> * linux-aarch64-low.c (aarch64_arch_setup): Remove code and call aarch64_linux_get_debug_reg_capacity.
186 lines
6.7 KiB
C
186 lines
6.7 KiB
C
/* Copyright (C) 2009-2015 Free Software Foundation, Inc.
|
|
Contributed by ARM Ltd.
|
|
|
|
This file is part of GDB.
|
|
|
|
This program is free software; you can redistribute it and/or modify
|
|
it under the terms of the GNU General Public License as published by
|
|
the Free Software Foundation; either version 3 of the License, or
|
|
(at your option) any later version.
|
|
|
|
This program is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
GNU General Public License for more details.
|
|
|
|
You should have received a copy of the GNU General Public License
|
|
along with this program. If not, see <http://www.gnu.org/licenses/>. */
|
|
|
|
#ifndef AARCH64_LINUX_HW_POINT_H
|
|
#define AARCH64_LINUX_HW_POINT_H 1
|
|
|
|
/* Macro definitions, data structures, and code for the hardware
|
|
breakpoint and hardware watchpoint support follow. We use the
|
|
following abbreviations throughout the code:
|
|
|
|
hw - hardware
|
|
bp - breakpoint
|
|
wp - watchpoint */
|
|
|
|
/* Maximum number of hardware breakpoint and watchpoint registers.
|
|
Neither of these values may exceed the width of dr_changed_t
|
|
measured in bits. */
|
|
|
|
#define AARCH64_HBP_MAX_NUM 16
|
|
#define AARCH64_HWP_MAX_NUM 16
|
|
|
|
/* Alignment requirement in bytes for addresses written to
|
|
hardware breakpoint and watchpoint value registers.
|
|
|
|
A ptrace call attempting to set an address that does not meet the
|
|
alignment criteria will fail. Limited support has been provided in
|
|
this port for unaligned watchpoints, such that from a GDB user
|
|
perspective, an unaligned watchpoint may be requested.
|
|
|
|
This is achieved by minimally enlarging the watched area to meet the
|
|
alignment requirement, and if necessary, splitting the watchpoint
|
|
over several hardware watchpoint registers. */
|
|
|
|
#define AARCH64_HBP_ALIGNMENT 4
|
|
#define AARCH64_HWP_ALIGNMENT 8
|
|
|
|
/* The maximum length of a memory region that can be watched by one
|
|
hardware watchpoint register. */
|
|
|
|
#define AARCH64_HWP_MAX_LEN_PER_REG 8
|
|
|
|
/* ptrace hardware breakpoint resource info is formatted as follows:
|
|
|
|
31 24 16 8 0
|
|
+---------------+--------------+---------------+---------------+
|
|
| RESERVED | RESERVED | DEBUG_ARCH | NUM_SLOTS |
|
|
+---------------+--------------+---------------+---------------+ */
|
|
|
|
|
|
/* Macros to extract fields from the hardware debug information word. */
|
|
#define AARCH64_DEBUG_NUM_SLOTS(x) ((x) & 0xff)
|
|
#define AARCH64_DEBUG_ARCH(x) (((x) >> 8) & 0xff)
|
|
|
|
/* Macro for the expected version of the ARMv8-A debug architecture. */
|
|
#define AARCH64_DEBUG_ARCH_V8 0x6
|
|
|
|
/* ptrace expects control registers to be formatted as follows:
|
|
|
|
31 13 5 3 1 0
|
|
+--------------------------------+----------+------+------+----+
|
|
| RESERVED (SBZ) | LENGTH | TYPE | PRIV | EN |
|
|
+--------------------------------+----------+------+------+----+
|
|
|
|
The TYPE field is ignored for breakpoints. */
|
|
|
|
#define DR_CONTROL_ENABLED(ctrl) (((ctrl) & 0x1) == 1)
|
|
#define DR_CONTROL_LENGTH(ctrl) (((ctrl) >> 5) & 0xff)
|
|
|
|
/* Each bit of a variable of this type is used to indicate whether a
|
|
hardware breakpoint or watchpoint setting has been changed since
|
|
the last update.
|
|
|
|
Bit N corresponds to the Nth hardware breakpoint or watchpoint
|
|
setting which is managed in aarch64_debug_reg_state, where N is
|
|
valid between 0 and the total number of the hardware breakpoint or
|
|
watchpoint debug registers minus 1.
|
|
|
|
When bit N is 1, the corresponding breakpoint or watchpoint setting
|
|
has changed, and therefore the corresponding hardware debug
|
|
register needs to be updated via the ptrace interface.
|
|
|
|
In the per-thread arch-specific data area, we define two such
|
|
variables for per-thread hardware breakpoint and watchpoint
|
|
settings respectively.
|
|
|
|
This type is part of the mechanism which helps reduce the number of
|
|
ptrace calls to the kernel, i.e. avoid asking the kernel to write
|
|
to the debug registers with unchanged values. */
|
|
|
|
typedef ULONGEST dr_changed_t;
|
|
|
|
/* Set each of the lower M bits of X to 1; assert X is wide enough. */
|
|
|
|
#define DR_MARK_ALL_CHANGED(x, m) \
|
|
do \
|
|
{ \
|
|
gdb_assert (sizeof ((x)) * 8 >= (m)); \
|
|
(x) = (((dr_changed_t)1 << (m)) - 1); \
|
|
} while (0)
|
|
|
|
#define DR_MARK_N_CHANGED(x, n) \
|
|
do \
|
|
{ \
|
|
(x) |= ((dr_changed_t)1 << (n)); \
|
|
} while (0)
|
|
|
|
#define DR_CLEAR_CHANGED(x) \
|
|
do \
|
|
{ \
|
|
(x) = 0; \
|
|
} while (0)
|
|
|
|
#define DR_HAS_CHANGED(x) ((x) != 0)
|
|
#define DR_N_HAS_CHANGED(x, n) ((x) & ((dr_changed_t)1 << (n)))
|
|
|
|
/* Structure for managing the hardware breakpoint/watchpoint resources.
|
|
DR_ADDR_* stores the address, DR_CTRL_* stores the control register
|
|
content, and DR_REF_COUNT_* counts the numbers of references to the
|
|
corresponding bp/wp, by which way the limited hardware resources
|
|
are not wasted on duplicated bp/wp settings (though so far gdb has
|
|
done a good job by not sending duplicated bp/wp requests). */
|
|
|
|
struct aarch64_debug_reg_state
|
|
{
|
|
/* hardware breakpoint */
|
|
CORE_ADDR dr_addr_bp[AARCH64_HBP_MAX_NUM];
|
|
unsigned int dr_ctrl_bp[AARCH64_HBP_MAX_NUM];
|
|
unsigned int dr_ref_count_bp[AARCH64_HBP_MAX_NUM];
|
|
|
|
/* hardware watchpoint */
|
|
CORE_ADDR dr_addr_wp[AARCH64_HWP_MAX_NUM];
|
|
unsigned int dr_ctrl_wp[AARCH64_HWP_MAX_NUM];
|
|
unsigned int dr_ref_count_wp[AARCH64_HWP_MAX_NUM];
|
|
};
|
|
|
|
/* Per-thread arch-specific data we want to keep. */
|
|
|
|
struct arch_lwp_info
|
|
{
|
|
/* When bit N is 1, it indicates the Nth hardware breakpoint or
|
|
watchpoint register pair needs to be updated when the thread is
|
|
resumed; see aarch64_linux_prepare_to_resume. */
|
|
dr_changed_t dr_changed_bp;
|
|
dr_changed_t dr_changed_wp;
|
|
};
|
|
|
|
extern int aarch64_num_bp_regs;
|
|
extern int aarch64_num_wp_regs;
|
|
|
|
unsigned int aarch64_watchpoint_length (unsigned int ctrl);
|
|
|
|
int aarch64_handle_breakpoint (enum target_hw_bp_type type, CORE_ADDR addr,
|
|
int len, int is_insert,
|
|
struct aarch64_debug_reg_state *state);
|
|
int aarch64_handle_watchpoint (enum target_hw_bp_type type, CORE_ADDR addr,
|
|
int len, int is_insert,
|
|
struct aarch64_debug_reg_state *state);
|
|
|
|
void aarch64_notify_debug_reg_change (const struct aarch64_debug_reg_state *state,
|
|
int is_watchpoint, unsigned int idx);
|
|
|
|
void aarch64_linux_set_debug_regs (const struct aarch64_debug_reg_state *state,
|
|
int tid, int watchpoint);
|
|
|
|
void aarch64_show_debug_reg_state (struct aarch64_debug_reg_state *state,
|
|
const char *func, CORE_ADDR addr,
|
|
int len, enum target_hw_bp_type type);
|
|
|
|
void aarch64_linux_get_debug_reg_capacity (int tid);
|
|
|
|
#endif /* AARCH64_LINUX_HW_POINT_H */
|