SEC_LOAD set.
* compile.c (sim_resume, case "O_NOT"): Use ONOT instead
of OSHIFTS.
(ONOT): Define.
(sim_resume, shift/rotate cases): Add support for shift/rotate
by two bits.
(OSHIFTS): Corresponding changes.
Handling more H8/S ops.
* h8300.h (UNOP3): Mark the register operand in this insn
as a source operand, not a destination operand.
(SHIFT_2, SHIFT_IMM): Remove. Eliminate all references.
(UNOP3): Change SHIFT_IMM to IMM for H8/S bitops. Mark
register operand with SRC_IN_DST.
More hackery for new shift ops on the H8/S.
* libbfd.h: Rebuild.
* i386lynx.c (KEEPIT): Define as udata.i.
(NAME(lynx,swap_std_reloc_out)): Don't use stoi.
(NAME(lynx,swap_ext_reloc_out)): Likewise.
* riscix.c (riscix_swap_std_reloc_out): Use udata.i rather than
flags. Don't use stoi.
with XCOFF_DEF_DYNAMIC set is really defined.
(xcoff_link_check_dynamic_ar_symbols): Likewise.
The above is for PR 9997.
(xcoff_link_add_symbols): Only create special sections if using an
XCOFF hash table.
* elf64-alpha.c (struct alpha_elf_link_hash_entry): Add flags
field.
(ALPHA_ELF_LINK_HASH_LU_ADDR): Define.
(ALPHA_ELF_LINK_HASH_LU_MEM): Define.
(ALPHA_ELF_LINK_HASH_LU_FUNC): Define.
(elf64_alpha_link_hash_newfunc): Initialize flags field.
(elf64_alpha_check_relocs): Record types of LITUSE entries that
are found for LITERAL relocs.
(elf64_alpha_adjust_dynamic_symbol): If a symbol has its address
taken, we cannot generate a .plt entry for the symbol.
* monitor.h,monitor.c:
Added monitor flags MO_NO_ECHO_ON_SETMEM (don't expect echo on
setmem command), MO_RUN_FIRST_TIME (if command to start process
running on target is different from one to continue execution),
MO_HEX_PREFIX (if addresses from monitor have a "0x" prefix).
* monitor.c,parse.c,sparc-tdep.c:
Don't require strings in the registers array. This is to allow
NULLs to be place holders in the tm-*.h file so that only minor
changes are needed when a new processor is introduced (eg, one
without floating point).
* sparc-tdep.c: Conditionally remove dependancies on floating point.
* sparclet-rom.c,config/sparc/sparclet.mt,config/sparc/tm-sparclet.h:
New files for target sparclet.
* symfile.c: Add option for 2nd parameter on load command : a load
offset added to the vma of each section.
* monitor.h,monitor.c:
Added monitor flags MO_NO_ECHO_ON_SETMEM (don't expect echo on
setmem command), MO_RUN_FIRST_TIME (if command to start process
running on target is different from one to continue execution),
MO_HEX_PREFIX (if addresses from monitor have a "0x" prefix).
* monitor.c,parse.c,sparc-tdep.c:
Don't require strings in the registers array. This is to allow
NULLs to be place holders in the tm-*.h file so that only minor
changes are needed when a new processor is introduced (eg, one
without floating point).
* sparc-tdep.c: Conditionally remove dependancies on floating point.
* sparclet-rom.c,config/sparc/sparclet.mt,config/sparc/tm-sparclet.h:
New files for target sparclet.
* symfile.c: Add option for 2nd parameter on load command : a load
offset added to the vma of each section.
Add option "tcp_remote" to target command if using
tcp to connect to a remote host which is then connected
via serial port to the e7000 (for exampole, a port master).
(e7000_open): Change to call e7000_parse_device.
gdb initialization, also report how long dejagnu waited. Restore
old timeout before doing error return. Temporarily increase timeout
by 3 minutes to allow for slow startups over heavy NFS use.
