This patch is to fixup the siginfo_t when aarch64 gdb or gdbserver
read from or write to the arm inferior. It is to convert the
"struct siginfo_t" between aarch64 and arm, which is quite mechanical.
gdb/gdbserver:
2015-09-15 Yao Qi <yao.qi@linaro.org>
* linux-aarch64-low.c (aarch64_linux_siginfo_fixup): New
function.
(struct linux_target_ops the_low_target): Install
aarch64_linux_siginfo_fixup.
gdb:
2015-09-15 Yao Qi <yao.qi@linaro.org>
* aarch64-linux-nat.c (aarch64_linux_siginfo_fixup): New function.
(_initialize_aarch64_linux_nat): Call linux_nat_set_siginfo_fixup.
* nat/aarch64-linux.c (aarch64_compat_siginfo_from_siginfo):
New function.
(aarch64_siginfo_from_compat_siginfo): New function.
* nat/aarch64-linux.h: Include signal.h.
(compat_int_t, compat_uptr_t, compat_time_t): Typedef.
(compat_timer_t, compat_clock_t): Likewise.
(struct compat_timeval): New.
(union compat_sigval): New.
(struct compat_siginfo): New.
(cpt_si_pid, cpt_si_uid, cpt_si_timerid): New macros.
(cpt_si_overrun, cpt_si_status, cpt_si_utime): Likewise.
(cpt_si_stime, cpt_si_ptr, cpt_si_addr): Likewise.
(cpt_si_band, cpt_si_fd): Likewise.
Nowadays, if user requests HW watchpoint to monitor a large memory area
or unaligned area, aarch64 GDB will split into multiple aligned areas,
and use multiple debugging registers to watch them. However, the
registers are not updated in a transaction way. GDBserver doesn't revert
updates in previous iterations if some debugging registers fail to update
due to some reason, like no free debugging registers available, in the
latter iteration. For example, if we have a char buf[34], and watch buf
in gdb,
(gdb) watch buf
Hardware watchpoint 2: buf
(gdb) c
Continuing.
infrun: clear_proceed_status_thread (Thread 13466)
infrun: proceed (addr=0xffffffffffffffff, signal=GDB_SIGNAL_DEFAULT)
infrun: step-over queue now empty
infrun: resuming [Thread 13466] for step-over
Sending packet: $m410838,22#35...Packet received: 00000000000000000000000000000000000000000000000000000000000000000000
infrun: skipping breakpoint: stepping past insn at: 0x400524
infrun: skipping breakpoint: stepping past insn at: 0x400524
Sending packet: $Z2,410838,22#80...Packet received: E01 <----- [1]
Packet Z2 (write-watchpoint) is supported
Sending packet: $Z0,7fb7fe0a8c,4#43...Packet received: OK
Warning:
Could not insert hardware watchpoint 2.
Could not insert hardware breakpoints:
You may have requested too many hardware breakpoints/watchpoints.
GDB receives E01 for Z2 packet [1] but GDBserver updates the debugging
register status,
insert_point (addr=0x00410838, len=34, type=hw-write-watchpoint):
BREAKPOINTs:
BP0: addr=0x0, ctrl=0x00000000, ref.count=0
BP1: addr=0x0, ctrl=0x00000000, ref.count=0
BP2: addr=0x0, ctrl=0x00000000, ref.count=0
BP3: addr=0x0, ctrl=0x00000000, ref.count=0
BP4: addr=0x0, ctrl=0x00000000, ref.count=0
BP5: addr=0x0, ctrl=0x00000000, ref.count=0
WATCHPOINTs:
WP0: addr=0x410850, ctrl=0x00001ff5, ref.count=1
WP1: addr=0x410848, ctrl=0x00001ff5, ref.count=1
WP2: addr=0x410840, ctrl=0x00001ff5, ref.count=1
WP3: addr=0x410838, ctrl=0x00001ff5, ref.count=1
four debugging registers can not monitor 34-byte long area, so the last
iteration of updating debugging register state fails but previous
iterations succeed. This makes GDB think no HW watchpoint is inserted
but some debugging registers are used.
This problem was exposed by "watch buf" gdb.base/watchpoint.exp with
aarch64 GDBserver debugging arm 32-bit program. The buf is 30-byte long
but 4-byte aligned, and four debugging registers can't cover 34-byte
(extend 4 bytes to be 8-byte aligned) area. However, this problem
does exist on non-multi-arch debugging scenario as well.
This patch moves code in aarch64_linux_region_ok_for_hw_watchpoint to
aarch64_linux_region_ok_for_watchpoint in nat/aarch64-linux-hw-point.c.
Then, checks with aarch64_linux_region_ok_for_watchpoint, like what we
are doing in GDB. If the region is OK, call aarch64_handle_watchpoint.
Regression tested on aarch64 with both 64-bit program and 32-bit
program. Some fails in gdb.base/watchpoint.exp are fixed.
gdb:
2015-09-03 Yao Qi <yao.qi@linaro.org>
* aarch64-linux-nat.c (aarch64_linux_region_ok_for_hw_watchpoint):
Move code to aarch64_linux_region_ok_for_watchpoint. Call
aarch64_linux_region_ok_for_watchpoint.
* nat/aarch64-linux-hw-point.c (aarch64_linux_region_ok_for_watchpoint):
New function.
* nat/aarch64-linux-hw-point.h (aarch64_linux_region_ok_for_watchpoint):
Declare it.
gdb/gdbserver:
2015-09-03 Yao Qi <yao.qi@linaro.org>
* linux-aarch64-low.c (aarch64_insert_point): Call
aarch64_handle_watchpoint if aarch64_linux_region_ok_for_watchpoint
returns true.
This patch moves aarch64_linux_new_thread in GDB and GDBserver to
nat/aarch64-linux.c.
gdb:
2015-08-25 Yao Qi <yao.qi@linaro.org>
* aarch64-linux-nat.c (aarch64_linux_new_thread): Move it to ...
* nat/aarch64-linux.c (aarch64_linux_new_thread): ... here.
* nat/aarch64-linux.h (aarch64_linux_new_thread): Declare.
gdb/gdbserver:
2015-08-25 Yao Qi <yao.qi@linaro.org>
* linux-aarch64-low.c (aarch64_linux_new_thread): Remove.
gdb:
2015-08-25 Yao Qi <yao.qi@linaro.org>
* aarch64-linux-nat.c (aarch64_linux_prepare_to_resume): Use
lwp_arch_private_info and ptid_of_lwp.
gdb/gdbserver:
2015-08-25 Yao Qi <yao.qi@linaro.org>
* linux-aarch64-low.c (aarch64_linux_prepare_to_resume): Use
lwp_arch_private_info and ptid_of_lwp.
This patch addes argument pid in aarch64_get_debug_reg_state, so that
its interface is the same on both GDB and GDBserver.
gdb/gdbserver:
2015-018-25 Yao Qi <yao.qi@linaro.org>
* linux-aarch64-low.c (aarch64_get_debug_reg_state): Add argument pid.
Find proc_info by find_process_pid. All callers updated.
This patch makes function debug_reg_change_callback in GDB and GDBserver
look the same, so that the following patch can move them to
nat/aarch64-linux-hw-point.c.
gdb:
2015-08-25 Yao Qi <yao.qi@linaro.org>
* aarch64-linux-nat.c (debug_reg_change_callback): Use
ptid_of_lwp to get ptid of lwp.
gdb/gdbserver:
2015-08-25 Yao Qi <yao.qi@linaro.org>
* linux-aarch64-low.c (debug_reg_change_callback): Use
ptid_of_lwp to get ptid of lwp.
gdb:
2015-08-25 Yao Qi <yao.qi@linaro.org>
* aarch64-linux-nat.c (debug_reg_change_callback): Use
debug_printf.
gdb/gdbserver:
2015-08-25 Yao Qi <yao.qi@linaro.org>
* linux-aarch64-low.c (debug_reg_change_callback): Use
debug_printf.
This patch is to use phex in debug_reg_change_callback to make it
identical in GDB and GDBserver.
gdb/gdbserver:
2015-08-25 Yao Qi <yao.qi@linaro.org>
* linux-aarch64-low.c (debug_reg_change_callback): Use phex.
This patch makes more bits on aarch64 watchpoint between GDB and GDBserver
look similar.
gdb/gdbserver:
2015-08-25 Yao Qi <yao.qi@linaro.org>
* linux-aarch64-low.c (aarch64_dr_update_callback_param) <pid>:
Remove.
(debug_reg_change_callback): Remove argument entry and add argument
lwp. Remove local variable thread. Don't print thread id in the
debugging output. Don't check whether pid of thread equals to pid.
(aarch64_notify_debug_reg_change): Don't set param.pid. Call
iterate_over_lwps instead find_inferior.
We only support tracepoint for aarch64. Although arm program can run
on aarch64, GDBserver doesn't support tracepoint for it.
gdb/gdbserver:
2015-08-04 Yao Qi <yao.qi@linaro.org>
* linux-aarch64-low.c (aarch64_supports_tracepoints): Return 0
if current_thread is 32 bit.
In multi-arch debugging, if GDB sends Z0 packet, GDBserver should be
able to do several things below:
- choose the right breakpoint instruction to insert according to the
information available, such as 'kind' in Z0 packet and address,
- choose the right breakpoint instruction to check memory writes and
validate inserted memory breakpoint
- be aware of different breakpoint instructions in $ARCH_breakpoint_at.
unfortunately GDBserver can't do them now. Although x86 GDBserver
supports multi-arch, it doesn't need to support them above because
breakpoint instruction on i686 and x86_64 is the same. However,
breakpoint instructions on aarch64 and arm (arm mode, thumb1, and thumb2)
are different.
I tried to teach aarch64 GDBserver backend to be really
multi-arch-capable in the following ways,
- linux_low_target return the right breakpoint instruction according to
the 'kind' in Z0 packet, and insert_memory_breakpoint can do the right
thing.
- once breakpoint is inserted, the breakpoint data and length is recorded
in each breakpoint object, so that validate_breakpoint and
check_mem_write can get the right breakpoint instruction from each
breakpoint object, rather than from global variable breakpoint_data.
- linux_low_target needs another hook function for pc increment after
hitting a breakpoint.
- let set_breakpoint_at, which is widely used for tracepoint, use the
'default' breakpoint instruction. We can always use aarch64 breakpoint
instruction since arm doesn't support tracepoint yet.
looks it is not a small piece of work, so I decide to disable Z0 packet
on multi-arch, which means aarch64 GDBserver only supports Z0 packet
if it is started to debug only one process (extended protocol is not
used) and process target description is 64-bit.
gdb/gdbserver:
2015-08-04 Yao Qi <yao.qi@linaro.org>
* linux-aarch64-low.c (aarch64_supports_z_point_type): Return
0 for Z_PACKET_SW_BP if it may be used in multi-arch debugging.
* server.c (extended_protocol): Remove "static".
* server.h (extended_protocol): Declare it.
gdb/gdbserver:
2015-08-04 Yao Qi <yao.qi@linaro.org>
* linux-aarch64-low.c (aarch64_get_pc): Get PC register on
both aarch64 and aarch32.
(aarch64_set_pc): Likewise.
This patch teaches aarch64-linux GDBserver use 32-bit arm target
description and regs_info if the elf file is 32-bit.
gdb/gdbserver:
2015-08-04 Yao Qi <yao.qi@linaro.org>
* configure.srv (case aarch64*-*-linux*): Append arm-with-neon.o
to srv_regobj and append arm-core.xml arm-vfpv3.xml and
arm-with-neon.xml to srv_xmlfiles.
* linux-aarch64-low.c: Include linux-aarch32-low.h.
(is_64bit_tdesc): New function.
(aarch64_linux_read_description): New function.
(aarch64_arch_setup): Call aarch64_linux_read_description.
(regs_info): Rename to regs_info_aarch64.
(aarch64_regs_info): Return right regs_info.
(initialize_low_arch): Call initialize_low_arch_aarch32.
There are also some duplication on getting HW watchpoint/breakpoint
registers info between GDB and GDBserver. This patch moves them
to nat/aarch64-linux-hw-point.c.
Note that ENABLE_NLS is not defined in GDBserver, so it should be OK
to use _( markup.
gdb:
2015-07-21 Yao Qi <yao.qi@linaro.org>
* aarch64-linux-nat.c (aarch64_linux_get_debug_reg_capacity):
Move it to nat/aarch64-linux-hw-point.c.
(aarch64_linux_child_post_startup_inferior): Update.
* nat/aarch64-linux-hw-point.c (aarch64_linux_get_debug_reg_capacity):
New function.
* nat/aarch64-linux-hw-point.h (aarch64_linux_get_debug_reg_capacity):
Declare it.
gdb/gdbserver:
2015-07-21 Yao Qi <yao.qi@linaro.org>
* linux-aarch64-low.c (aarch64_arch_setup): Remove code and call
aarch64_linux_get_debug_reg_capacity.
When I look at test fails related to watchpoint on aarch64-linux,
I find there are some code duplicates between GDB and GDBserver.
This patch is to move some of them to a nat/aarch64-linux-hw-point.{h,c}.
The only change I do is about the dr_changed_t typedef, which was
ULONGEST in GDB and 'unsigned long long' in GDBserver. Each bit
of dr_changed_t represents a status of each HW breakpoint or
watchpoint register, and the max number of HW breakpoint or watchpoint
registers is 16, so the width of 'unsigned long long' is sufficient.
gdb:
2015-07-17 Yao Qi <yao.qi@linaro.org>
* Makefile.in (HFILES_NO_SRCDIR): Add
nat/aarch64-linux-hw-point.h.
(aarch64-linux-hw-point.o): New rule.
* nat/aarch64-linux-hw-point.h: New file.
* nat/aarch64-linux-hw-point.c: New file.
* aarch64-linux-nat.c: Include nat/aarch64-linux-hw-point.h.
(AARCH64_HBP_MAX_NUM): Move to nat/aarch64-linux-hw-point.h.
(AARCH64_HWP_MAX_NUM, AARCH64_HBP_ALIGNMENT): Likewise.
(AARCH64_HWP_ALIGNMENT): Likewise.
(AARCH64_HWP_MAX_LEN_PER_REG): Likewise.
(AARCH64_DEBUG_NUM_SLOTS, AARCH64_DEBUG_ARCH): Likewise.
(AARCH64_DEBUG_ARCH_V8, DR_MARK_ALL_CHANGED): Likewise.
(DR_MARK_N_CHANGED, DR_CLEAR_CHANGED): Likewise.
(DR_HAS_CHANGED, DR_N_HAS_CHANGE): Likewise.
(aarch64_num_bp_regs, aarch64_num_wp_regs): Likewise.
(struct aarch64_debug_reg_state): Likewise.
(struct arch_lwp_info): Likewise.
(aarch64_linux_set_debug_regs): Likewise.
(aarch64_notify_debug_reg_change): Remove static.
(aarch64_align_watchpoint): Likewise.
(DR_CONTROL_ENABLED, DR_CONTROL_LENGTH): Likewise.
(aarch64_watchpoint_length): Likewise.
(aarch64_point_encode_ctrl_reg): Likewise
(aarch64_point_is_aligned): Likewise.
(aarch64_dr_state_insert_one_point): Likewise.
(aarch64_dr_state_remove_one_point): Likewise.
(aarch64_handle_breakpoint): Likewise.
(aarch64_handle_aligned_watchpoint): Likewise.
(aarch64_handle_unaligned_watchpoint): Likewise.
(aarch64_handle_watchpoint): Likewise.
* config/aarch64/linux.mh (NAT_FILE): Add
aarch64-linux-hw-point.o.
gdb/gdbserver:
2015-07-17 Yao Qi <yao.qi@linaro.org>
* Makefile.in (aarch64-linux-hw-point.o): New rule.
* configure.srv (srv_tgtobj): Append aarch64-linux-hw-point.o.
* linux-aarch64-low.c: Include nat/aarch64-linux-hw-point.h.
(AARCH64_HBP_MAX_NUM): Move to nat/aarch64-linux-hw-point.h.
(AARCH64_HWP_MAX_NUM, AARCH64_HBP_ALIGNMENT): Likewise.
(AARCH64_HWP_ALIGNMENT): Likewise.
(AARCH64_HWP_MAX_LEN_PER_REG): Likewise.
(AARCH64_DEBUG_NUM_SLOTS, AARCH64_DEBUG_ARCH): Likewise.
(aarch64_num_bp_regs, aarch64_num_wp_regs): Likewise.
(AARCH64_DEBUG_ARCH_V8, DR_MARK_ALL_CHANGED): Likewise.
(DR_MARK_N_CHANGED, DR_CLEAR_CHANGED): Likewise.
(DR_HAS_CHANGED, DR_N_HAS_CHANGE): Likewise.
(struct aarch64_debug_reg_state): Likewise.
(struct arch_lwp_info): Likewise.
(aarch64_align_watchpoint): Likewise.
(DR_CONTROL_ENABLED, DR_CONTROL_LENGTH): Likewise.
(aarch64_watchpoint_length): Likewise.
(aarch64_point_encode_ctrl_reg): Likewise
(aarch64_point_is_aligned): Likewise.
(aarch64_align_watchpoint): Likewise.
(aarch64_linux_set_debug_regs):
(aarch64_dr_state_insert_one_point): Likewise.
(aarch64_dr_state_remove_one_point): Likewise.
(aarch64_handle_breakpoint): Likewise.
(aarch64_handle_aligned_watchpoint): Likewise.
(aarch64_handle_unaligned_watchpoint): Likewise.
(aarch64_handle_watchpoint): Likewise.
Some functions on handling HW watchpoint in GDB and GDBserver looks the
same except the code getting debug register state from current inferior.
In GDB, we get debug register state like this:
state = aarch64_get_debug_reg_state (ptid_get_pid (inferior_ptid));
while in GDBserver, we get debug register state like this:
state = aarch64_get_debug_reg_state ();
This patch is to move two lines above out of some functions, and pass
aarch64_debug_reg_state to these functions, in this way, these functions
are the same, and can be moved to a common place.
gdb:
2015-07-17 Yao Qi <yao.qi@linaro.org>
* aarch64-linux-nat.c (aarch64_handle_breakpoint): Add argument
state and don't call aarch64_get_debug_reg_state. All callers
update.
(aarch64_linux_insert_hw_breakpoint): Call
aarch64_get_debug_reg_state earlier.
(aarch64_linux_remove_hw_breakpoint): Likewise.
(aarch64_handle_aligned_watchpoint): Add argument state and
don't call aarch64_get_debug_reg_state. All callers update.
(aarch64_handle_unaligned_watchpoint): Likewise.
(aarch64_handle_watchpoint): Add argument state.
(aarch64_linux_insert_watchpoint): Call aarch64_get_debug_reg_state
earlier.
(aarch64_linux_remove_watchpoint): Likewise.
gdb/gdbserver:
2015-07-17 Yao Qi <yao.qi@linaro.org>
* linux-aarch64-low.c (aarch64_handle_breakpoint): Add argument state
and don't aarch64_get_debug_reg_state. All callers update.
(aarch64_handle_aligned_watchpoint): Likewise.
(aarch64_handle_unaligned_watchpoint): Likewise.
(aarch64_handle_watchpoint): Likewise.
(aarch64_insert_point): Call aarch64_get_debug_reg_state earlier.
(aarch64_remove_point): Likewise.
Some functions in aarch64-linux-nat.c and linux-aarch64-low.c looks
the same except for the code printing debug message. In GDB, we use
fprintf_unfiltered (gdb_stdlog, ...) while in GDBserver, we use
fprintf (stderr, ...). This patch is to change them to use debug_printf
so that these functions are the same, and I can move them to a common
place in the following patch.
gdb:
2015-07-17 Yao Qi <yao.qi@linaro.org>
* aarch64-linux-nat.c (aarch64_show_debug_reg_state): Use
debug_printf.
(aarch64_handle_unaligned_watchpoint): Likewise.
gdb/gdbserver:
2015-07-17 Yao Qi <yao.qi@linaro.org>
* linux-aarch64-low.c (aarch64_show_debug_reg_state): Use
debug_printf.
(aarch64_handle_unaligned_watchpoint): Likewise.
This patch cleans up the comments for each linux_target_ops methods. We
should mention which method each function implements but there is no
need to duplicate information already mentionned in the base target_ops
or linux_target_ops definitions.
gdb/gdbserver/ChangeLog:
* linux-aarch64-low.c: Add comments for each linux_target_ops
method. Remove comments already covered in target_ops and
linux_target_ops definitions.
(the_low_target): Add comments for each unimplemented method.
Hi,
I happen to read the comments in regs_info below,
struct regs_info
{
...
/* Info used when accessing registers with PTRACE_PEEKUSER /
PTRACE_POKEUSER. This can be NULL if all registers are
transferred with regsets .*/
struct usrregs_info *usrregs;
that usrregs can be NULL if all registers are transferred with
regsets, which is exactly what aarch64-linux does. This patch
is to set usrregs to NULL in regs_info and remove
aarch64_usrregs_info and aarch64_regmap.
gdb/gdbserver:
2015-07-09 Yao Qi <yao.qi@linaro.org>
* linux-aarch64-low.c (aarch64_regmap): Remove.
(aarch64_usrregs_info): Remove.
(regs_info): Set field usrregs to NULL.
This patch lets GDBServer handle software breakpoints instead of relying
on GDB.
gdb/gdbserver/ChangeLog:
* linux-aarch64-low.c (aarch64_supports_z_point_type): Enable for
Z_PACKET_SW_BP.
GDB uses a "brk #0" instruction to perform a software breakpoint while
GDBServer uses an illegal instruction. Both instructions should match.
When enabling support for the 'Z0' packet, we let GDBServer insert the
breakpoint instruction instead of GDB. And in case of permanent
breakpoints for example, GDB will check if a breakpoint is inserted in the
inferior with `program_breakpoint_here_p (gdbarch, address)', and
compare the instruction read from the inferior with the breakpoint
instruction.
On AArch64, instructions are always little endian so we need to
represent it as an array of bytes, as done in aarch64-tdep.c.
gdb/gdbserver/ChangeLog:
* linux-aarch64-low.c: Remove comment about endianness.
(aarch64_breakpoint): Change type to gdb_byte[]. Set to "brk #0".
(aarch64_breakpoint_at): Change type of insn to gdb_byte[]. Use
memcmp.
Fix build errors introduced by
https://sourceware.org/ml/gdb-patches/2015-05/msg00281.html, which
didn't account for the change of the name of the struct process_info
field 'private' to 'priv' made in
https://sourceware.org/ml/gdb-patches/2015-02/msg00829.html.
gdb/gdbserver/ChangeLog:
* linux-aarch64-low.c (aarch64_linux_new_fork): Change reference
to process_info.private to process_info.priv.
* linux-arm-low.c (arm_new_fork): Likewise.
* linux-mips-low.c (mips_linux_new_fork): Likewise.
This patch implements the architecture-specific pieces of follow-fork
for remote and extended-remote Linux targets, which in the current
implementation copyies the parent's debug register state into the new
child's data structures. This is required for x86, arm, aarch64, and
mips.
This follows the native implementation as closely as possible by
implementing a new linux_target_ops function 'new_fork', which is
analogous to 'linux_nat_new_fork' in linux-nat.c. In gdbserver, the debug
registers are stored in the process list, instead of an
architecture-specific list, so the function arguments are process_info
pointers instead of an lwp_info and a pid as in the native implementation.
In the MIPS implementation the debug register mirror is stored differently
from x86, ARM, and aarch64, so instead of doing a simple structure assignment
I had to clone the list of watchpoint structures.
Tested using gdb.threads/watchpoint-fork.exp on x86, and ran manual tests
on a MIPS board and an ARM board. Aarch64 hasn't been tested.
gdb/gdbserver/ChangeLog:
* linux-aarch64-low.c (aarch64_linux_new_fork): New function.
(the_low_target) <new_fork>: Initialize new member.
* linux-arm-low.c (arm_new_fork): New function.
(the_low_target) <new_fork>: Initialize new member.
* linux-low.c (handle_extended_wait): Call new target function
new_fork.
* linux-low.h (struct linux_target_ops) <new_fork>: New member.
* linux-mips-low.c (mips_add_watchpoint): New function
extracted from mips_insert_point.
(the_low_target) <new_fork>: Initialize new member.
(mips_linux_new_fork): New function.
(mips_insert_point): Call mips_add_watchpoint.
* linux-x86-low.c (x86_linux_new_fork): New function.
(the_low_target) <new_fork>: Initialize new member.
This commit changes the signature of linux_target_ops.new_thread in
gdbserver to match that used in GDB's equivalent.
gdb/gdbserver/ChangeLog:
* linux-low.h (linux_target_ops) <new_thread>: Changed signature.
* linux-arm-low.c (arm_new_thread): Likewise.
* linux-aarch64-low.c (aarch64_linux_new_thread): Likewise.
* linux-mips-low.c (mips_linux_new_thread): Likewise.
* linux-x86-low.c (x86_linux_new_thread): Likewise.
* linux-low.c (add_lwp): Update the_low_target.new_thread call.
I happen to see that show_debug_regs is used as an arithmetic type,
but it should be a boolean,
if (show_debug_regs > 1)
On the other hand, GDB RSP only allows setting it to either 0 or 1,
so it makes no sense to check whether it is greater than 1. This
patch fixes it.
gdb/gdbserver:
2015-03-06 Yao Qi <yao.qi@linaro.org>
* linux-aarch64-low.c (aarch64_insert_point): Use
show_debug_regs as a boolean.
(aarch64_remove_point): Likewise.
This patch renames symbols that happen to have names which are
reserved keywords in C++.
Most of this was generated with Tromey's cxx-conversion.el script.
Some places where later hand massaged a bit, to fix formatting, etc.
And this was rebased several times meanwhile, along with re-running
the script, so re-running the script from scratch probably does not
result in the exact same output. I don't think that matters anyway.
gdb/
2015-02-27 Tom Tromey <tromey@redhat.com>
Pedro Alves <palves@redhat.com>
Rename symbols whose names are reserved C++ keywords throughout.
gdb/gdbserver/
2015-02-27 Tom Tromey <tromey@redhat.com>
Pedro Alves <palves@redhat.com>
Rename symbols whose names are reserved C++ keywords throughout.
When using aarch64 gdb with gdbserver, floating point registers are
not correctly displayed, as below:
(gdb) info registers fpsr fpcr
fpsr <unavailable>
fpcr <unavailable>
To fix these problems, the missing fpsr and fpcr registers are added
when floating point registers are read/write
Add test for aarch64 floating point
PR server/17457
gdb/gdbserver/
PR server/17457
* linux-aarch64-low.c (AARCH64_FPSR_REGNO): New define.
(AARCH64_FPCR_REGNO): Likewise.
(AARCH64_NUM_REGS): Update to include fpsr/fpcr registers.
(aarch64_fill_fpregset): Add missing fpsr/fpcr registers.
(aarch64_store_fpregset): Likewise.
gdb/testsuite/
PR server/17457
* gdb.arch/aarch64-fp.c: New file.
* gdb.arch/aarch64-fp.exp: New file.
Signed-off-by: Catalin Udma <catalin.udma@freescale.com>
GDB has a function named "current_inferior" and gdbserver has a global
variable named "current_inferior", but the two are not equivalent;
indeed, gdbserver does not have any real equivalent of what GDB calls
an inferior. What gdbserver's "current_inferior" is actually pointing
to is a structure describing the current thread. This commit renames
current_inferior as current_thread in gdbserver to clarify this. It
also renames the function "set_desired_inferior" to "set_desired_thread"
and renames various local variables from foo_inferior to foo_thread.
gdb/gdbserver/ChangeLog:
* inferiors.h (current_inferior): Renamed as...
(current_thread): New variable. All uses updated.
* linux-low.c (get_pc): Renamed saved_inferior as saved_thread.
(maybe_move_out_of_jump_pad): Likewise.
(cancel_breakpoint): Likewise.
(linux_low_filter_event): Likewise.
(wait_for_sigstop): Likewise.
(linux_resume_one_lwp): Likewise.
(need_step_over_p): Likewise.
(start_step_over): Likewise.
(linux_stabilize_threads): Renamed save_inferior as saved_thread.
* linux-x86-low.c (x86_linux_update_xmltarget): Likewise.
* proc-service.c (ps_lgetregs): Renamed reg_inferior as reg_thread
and save_inferior as saved_thread.
* regcache.c (get_thread_regcache): Renamed saved_inferior as
saved_thread.
(regcache_invalidate_thread): Likewise.
* remote-utils.c (prepare_resume_reply): Likewise.
* thread-db.c (thread_db_get_tls_address): Likewise.
(disable_thread_event_reporting): Likewise.
(remove_thread_event_breakpoints): Likewise.
* tracepoint.c (gdb_agent_about_to_close): Renamed save_inferior
as saved_thread.
* target.h (set_desired_inferior): Renamed as...
(set_desired_thread): New declaration. All uses updated.
* server.c (myresume): Updated comment to reference thread instead
of inferior.
(handle_serial_event): Likewise.
(handle_target_event): Likewise.
This commit adds a new global flag show_debug_regs to common-debug.h
to replace the flag debug_hw_points used by gdbserver and by the
Linux x86 and AArch64 ports, and to replace the flag maint_show_dr
used by the Linux MIPS port.
Note that some debug printing in the AArch64 port was enabled only if
debug_hw_points > 1 but no way to set debug_hw_points to values other
than 0 and 1 was provided; that code was effectively dead. This
commit enables all debug printing if show_debug_regs is nonzero, so
the AArch64 output will be more verbose than previously.
gdb/ChangeLog:
* common/common-debug.h (show_debug_regs): Declare.
* common/common-debug.c (show_debug_regs): Define.
* aarch64-linux-nat.c (debug_hw_points): Don't define. Replace
all uses with show_debug_regs. Replace all uses that considered
debug_hw_points as a multi-value integer with straight boolean
uses.
* x86-nat.c (debug_hw_points): Don't define. Replace all uses
with show_debug_regs.
* nat/x86-dregs.c (debug_hw_points): Don't declare. Replace
all uses with show_debug_regs.
* mips-linux-nat.c (maint_show_dr): Don't define. Replace all
uses with show_debug_regs.
gdb/gdbserver/ChangeLog:
* server.h (debug_hw_points): Don't declare.
* server.c (debug_hw_points): Don't define. Replace all uses
with show_debug_regs.
* linux-aarch64-low.c (debug_hw_points): Don't define. Replace
all uses with show_debug_regs.
A recent change to glibc removed asm/ptrace.h from user.h for AArch64.
This meant that cross-native builds of gdbserver using trunk glibc broke
because linux-aarch64-low.c because user_hwdebug_state couldn't be found.
This is like commit #036cd38182bde32d8297b630cd5c861d53b8949e
2014-05-23 Ramana Radhakrishnan <ramana.radhakrishnan@arm.com>
* linux-aarch64-low.c (asm/ptrace.h): Include.
This patch fixes hardware breakpoint regressions exposed by my fix for
"PR breakpoints/7143 - Watchpoint does not trigger when first set", at
https://sourceware.org/ml/gdb-patches/2014-03/msg00167.html
The testsuite caught them on Linux/x86_64, at least. gdb.sum:
gdb.sum:
FAIL: gdb.base/hbreak2.exp: next over recursive call
FAIL: gdb.base/hbreak2.exp: backtrace from factorial(5.1)
FAIL: gdb.base/hbreak2.exp: continue until exit at recursive next test
gdb.log:
(gdb) next
Program received signal SIGTRAP, Trace/breakpoint trap.
factorial (value=4) at ../../../src/gdb/testsuite/gdb.base/break.c:113
113 if (value > 1) { /* set breakpoint 7 here */
(gdb) FAIL: gdb.base/hbreak2.exp: next over recursive call
Actually, that patch just exposed a latent issue to "breakpoints
always-inserted off" mode, not really caused it. After that patch,
GDB no longer removes breakpoints at each internal event, thus making
some scenarios behave like breakpoint always-inserted on. The bug is
easy to trigger with always-inserted on.
The issue is that since the target-side breakpoint conditions support,
if the stub/server supports evaluating breakpoint conditions on the
target side, then GDB is sending duplicate Zx packets to the target
without removing them before, and GDBserver is not really expecting
that for Z packets other than Z0/z0. E.g., with "set breakpoint
always-inserted on" and "set debug remote 1":
(gdb) b main
Sending packet: $m410943,1#ff...Packet received: 48
Breakpoint 4 at 0x410943: file ../../../src/gdb/gdbserver/server.c, line 3028.
Sending packet: $Z0,410943,1#48...Packet received: OK
^^^^^^^^^^^^
(gdb) b main
Note: breakpoint 4 also set at pc 0x410943.
Sending packet: $m410943,1#ff...Packet received: 48
Breakpoint 5 at 0x410943: file ../../../src/gdb/gdbserver/server.c, line 3028.
Sending packet: $Z0,410943,1#48...Packet received: OK
^^^^^^^^^^^^
(gdb) b main
Note: breakpoints 4 and 5 also set at pc 0x410943.
Sending packet: $m410943,1#ff...Packet received: 48
Breakpoint 6 at 0x410943: file ../../../src/gdb/gdbserver/server.c, line 3028.
Sending packet: $Z0,410943,1#48...Packet received: OK
^^^^^^^^^^^^
(gdb) del
Delete all breakpoints? (y or n) y
Sending packet: $Z0,410943,1#48...Packet received: OK
Sending packet: $Z0,410943,1#48...Packet received: OK
Sending packet: $z0,410943,1#68...Packet received: OK
And for Z1, similarly:
(gdb) hbreak main
Sending packet: $m410943,1#ff...Packet received: 48
Hardware assisted breakpoint 4 at 0x410943: file ../../../src/gdb/gdbserver/server.c, line 3028.
Sending packet: $Z1,410943,1#49...Packet received: OK
^^^^^^^^^^^^
Packet Z1 (hardware-breakpoint) is supported
(gdb) hbreak main
Note: breakpoint 4 also set at pc 0x410943.
Sending packet: $m410943,1#ff...Packet received: 48
Hardware assisted breakpoint 5 at 0x410943: file ../../../src/gdb/gdbserver/server.c, line 3028.
Sending packet: $Z1,410943,1#49...Packet received: OK
^^^^^^^^^^^^
(gdb) hbreak main
Note: breakpoints 4 and 5 also set at pc 0x410943.
Sending packet: $m410943,1#ff...Packet received: 48
Hardware assisted breakpoint 6 at 0x410943: file ../../../src/gdb/gdbserver/server.c, line 3028.
Sending packet: $Z1,410943,1#49...Packet received: OK
^^^^^^^^^^^^
(gdb) del
Delete all breakpoints? (y or n) y
Sending packet: $Z1,410943,1#49...Packet received: OK
^^^^^^^^^^^^
Sending packet: $Z1,410943,1#49...Packet received: OK
^^^^^^^^^^^^
Sending packet: $z1,410943,1#69...Packet received: OK
^^^^^^^^^^^^
So GDB sent a bunch of Z1 packets, and then when finally removing the
breakpoint, only one z1 packet was sent. On the GDBserver side (with
monitor set debug-hw-points 1), in the Z1 case, we see:
$ ./gdbserver :9999 ./gdbserver
Process ./gdbserver created; pid = 8629
Listening on port 9999
Remote debugging from host 127.0.0.1
insert_watchpoint (addr=410943, len=1, type=instruction-execute):
CONTROL (DR7): 00000101 STATUS (DR6): 00000000
DR0: addr=0x410943, ref.count=1 DR1: addr=0x0, ref.count=0
DR2: addr=0x0, ref.count=0 DR3: addr=0x0, ref.count=0
insert_watchpoint (addr=410943, len=1, type=instruction-execute):
CONTROL (DR7): 00000101 STATUS (DR6): 00000000
DR0: addr=0x410943, ref.count=2 DR1: addr=0x0, ref.count=0
DR2: addr=0x0, ref.count=0 DR3: addr=0x0, ref.count=0
insert_watchpoint (addr=410943, len=1, type=instruction-execute):
CONTROL (DR7): 00000101 STATUS (DR6): 00000000
DR0: addr=0x410943, ref.count=3 DR1: addr=0x0, ref.count=0
DR2: addr=0x0, ref.count=0 DR3: addr=0x0, ref.count=0
insert_watchpoint (addr=410943, len=1, type=instruction-execute):
CONTROL (DR7): 00000101 STATUS (DR6): 00000000
DR0: addr=0x410943, ref.count=4 DR1: addr=0x0, ref.count=0
DR2: addr=0x0, ref.count=0 DR3: addr=0x0, ref.count=0
insert_watchpoint (addr=410943, len=1, type=instruction-execute):
CONTROL (DR7): 00000101 STATUS (DR6): 00000000
DR0: addr=0x410943, ref.count=5 DR1: addr=0x0, ref.count=0
DR2: addr=0x0, ref.count=0 DR3: addr=0x0, ref.count=0
remove_watchpoint (addr=410943, len=1, type=instruction-execute):
CONTROL (DR7): 00000101 STATUS (DR6): 00000000
DR0: addr=0x410943, ref.count=4 DR1: addr=0x0, ref.count=0
DR2: addr=0x0, ref.count=0 DR3: addr=0x0, ref.count=0
That's one insert_watchpoint call for each Z1 packet, and then one
remove_watchpoint call for the z1 packet. Notice how ref.count
increased for each insert_watchpoint call, and then in the end, after
GDB told GDBserver to forget about the hardware breakpoint, GDBserver
ends with the the first debug register still with ref.count=4! IOW,
the hardware breakpoint is left armed on the target, while on the GDB
end it's gone. If the program happens to execute 0x410943 afterwards,
then the CPU traps, GDBserver reports the trap to GDB, and GDB not
having a breakpoint set at that address anymore, reports to the user a
spurious SIGTRAP.
This is exactly what is happening in the hbreak2.exp test, though in
that case, it's a shared library event that triggers a
breakpoint_re_set, when breakpoints are still inserted (because
nowadays GDB doesn't remove breakpoints while handling internal
events), and that recreates breakpoint locations, which likewise
forces breakpoint reinsertion and Zx packet resends...
That is a lot of bogus Zx duplication that should possibly be
addressed on the GDB side. GDB resends Zx packets because the way to
change the target-side condition, is to resend the breakpoint to the
server with the new condition. (That's an option in the packet: e.g.,
"Z1,410943,1;X3,220027" for "hbreak main if 0". The packets in the
examples above are shorter because the breakpoints don't have
conditions attached). GDB doesn't remove the breakpoint first before
reinserting it because that'd be bad for non-stop, as it'd open a
window where the inferior could miss the breakpoint. The conditions
actually haven't changed between the resends, but GDB isn't smart
enough to realize that.
(TBC, if the target doesn't support target-side conditions, then GDB
doesn't trigger these resends (init_bp_location calls
mark_breakpoint_location_modified, and that does nothing if condition
evaluation is on the host side. The resends are caused by the
'loc->condition_changed = condition_modified.' line.)
But, even if GDB was made smarter, GDBserver should really still
handle the resends anyway. So target-side conditions also aren't
really to blame. The documentation of the Z/z packets says:
"To avoid potential problems with duplicate packets, the operations
should be implemented in an idempotent way."
As such, we may want to fix GDB, but we should definitely fix
GDBserver. The fix is a prerequisite for target-side conditions on
hardware breakpoints anyway (and while at it, on watchpoints too).
GDBserver indeed already treats duplicate Z0 packets in an idempotent
way. mem-break.c has the concept of high-level and low-level
breakpoints, somewhat similar to GDB's split of breakpoints vs
breakpoint locations, and keeps track of multiple breakpoints
referencing the same address/location, for the case of an internal
GDBserver breakpoint or a tracepoint being set at the same address as
a GDB breakpoint. But, it only allows GDB to ever contribute one
reference to a software breakpoint location. IOW, if gdbserver sees a
Z0 packet for the same address where it already had a GDB breakpoint
set, then GDBserver won't create another high-level GDB breakpoint.
However, mem-break.c only tracks GDB Z0 breakpoints. The same logic
should apply to all kinds of Zx packets. Currently, gdbserver passes
down each duplicate Zx (other than Z0) request directly to the
target->insert_point routine. The x86 watchpoint support itself
refcounts watchpoint / hw breakpoint requests, to handle overlapping
watchpoints, and save debug registers. But that code doesn't (and
really shouldn't) handle the duplicate requests, assuming that for
each insert there will be a corresponding remove.
So the fix is to generalize mem-break.c to track all kinds of Zx
breakpoints, and filter out duplicates. As mentioned, this ends up
adding support for target-side conditions on hardware breakpoints and
watchpoints too (though GDB itself doesn't support the latter yet).
Probably the least obvious change in the patch is that it kind of
turns the breakpoint insert/remove APIs inside out. Before, the
target methods were only called for GDB breakpoints. The internal
breakpoint set/delete methods inserted memory breakpoints directly
bypassing the insert/remove target methods. That's not good when the
target should use a debug API to set software breakpoints, instead of
relying on GDBserver patching memory with breakpoint instructions, as
is the case of NTO.
Now removal/insertion of all kinds of breakpoints/watchpoints, either
internal, or from GDB, always go through the target methods. The
insert_point/remove_point methods no longer get passed a Z packet
type, but an internal/raw breakpoint type. They're also passed a
pointer to the raw breakpoint itself (note that's still opaque outside
mem-break.c), so that insert_memory_breakpoint /
remove_memory_breakpoint have access to the breakpoint's shadow
buffer. I first tried passing down a new structure based on GDB's
"struct bp_target_info" (actually with that name exactly), but then
decided against it as unnecessary complication.
As software/memory breakpoints work by poking at memory, when setting
a GDB Z0 breakpoint (but not internal breakpoints, as those can assume
the conditions are already right), we need to tell the target to
prepare to access memory (which on Linux means stop threads). If that
operation fails, we need to return error to GDB. Seeing an error, if
this is the first breakpoint of that type that GDB tries to insert,
GDB would then assume the breakpoint type is supported, but it may
actually not be. So we need to check whether the type is supported at
all before preparing to access memory. And to solve that, the patch
adds a new target->supports_z_point_type method that is called before
actually trying to insert the breakpoint.
Other than that, hopefully the change is more or less obvious.
New test added that exercises the hbreak2.exp regression in a more
direct way, without relying on a breakpoint re-set happening before
main is reached.
Tested by building GDBserver for:
aarch64-linux-gnu
arm-linux-gnueabihf
i686-pc-linux-gnu
i686-w64-mingw32
m68k-linux-gnu
mips-linux-gnu
mips-uclinux
nios2-linux-gnu
powerpc-linux-gnu
sh-linux-gnu
tilegx-unknown-linux-gnu
x86_64-redhat-linux
x86_64-w64-mingw32
And also regression tested on x86_64 Fedora 20.
gdb/gdbserver/
2014-05-20 Pedro Alves <palves@redhat.com>
* linux-aarch64-low.c (aarch64_insert_point)
(aarch64_remove_point): No longer check whether the type is
supported here. Adjust to new interface.
(the_low_target): Install aarch64_supports_z_point_type as
supports_z_point_type method.
* linux-arm-low.c (raw_bkpt_type_to_arm_hwbp_type): New function.
(arm_linux_hw_point_initialize): Take an enum raw_bkpt_type
instead of a Z packet char. Adjust.
(arm_supports_z_point_type): New function.
(arm_insert_point, arm_remove_point): Adjust to new interface.
(the_low_target): Install arm_supports_z_point_type.
* linux-crisv32-low.c (cris_supports_z_point_type): New function.
(cris_insert_point, cris_remove_point): Adjust to new interface.
Don't check whether the type is supported here.
(the_low_target): Install cris_supports_z_point_type.
* linux-low.c (linux_supports_z_point_type): New function.
(linux_insert_point, linux_remove_point): Adjust to new interface.
* linux-low.h (struct linux_target_ops) <insert_point,
remove_point>: Take an enum raw_bkpt_type instead of a char. Add
raw_breakpoint pointer parameter.
<supports_z_point_type>: New method.
* linux-mips-low.c (mips_supports_z_point_type): New function.
(mips_insert_point, mips_remove_point): Adjust to new interface.
Use mips_supports_z_point_type.
(the_low_target): Install mips_supports_z_point_type.
* linux-ppc-low.c (the_low_target): Install NULL as
supports_z_point_type method.
* linux-s390-low.c (the_low_target): Install NULL as
supports_z_point_type method.
* linux-sparc-low.c (the_low_target): Install NULL as
supports_z_point_type method.
* linux-x86-low.c (x86_supports_z_point_type): New function.
(x86_insert_point): Adjust to new insert_point interface. Use
insert_memory_breakpoint. Adjust to new
i386_low_insert_watchpoint interface.
(x86_remove_point): Adjust to remove_point interface. Use
remove_memory_breakpoint. Adjust to new
i386_low_remove_watchpoint interface.
(the_low_target): Install x86_supports_z_point_type.
* lynx-low.c (lynx_target_ops): Install NULL as
supports_z_point_type callback.
* nto-low.c (nto_supports_z_point_type): New.
(nto_insert_point, nto_remove_point): Adjust to new interface.
(nto_target_ops): Install nto_supports_z_point_type.
* mem-break.c: Adjust intro comment.
(struct raw_breakpoint) <raw_type, size>: New fields.
<inserted>: Update comment.
<shlib_disabled>: Delete field.
(enum bkpt_type) <gdb_breakpoint>: Delete value.
<gdb_breakpoint_Z0, gdb_breakpoint_Z1, gdb_breakpoint_Z2,
gdb_breakpoint_Z3, gdb_breakpoint_Z4>: New values.
(raw_bkpt_type_to_target_hw_bp_type): New function.
(find_enabled_raw_code_breakpoint_at): New function.
(find_raw_breakpoint_at): New type and size parameters. Use them.
(insert_memory_breakpoint): New function, based off
set_raw_breakpoint_at.
(remove_memory_breakpoint): New function.
(set_raw_breakpoint_at): Reimplement.
(set_breakpoint): New, based on set_breakpoint_at.
(set_breakpoint_at): Reimplement.
(delete_raw_breakpoint): Go through the_target->remove_point
instead of assuming memory breakpoints.
(find_gdb_breakpoint_at): Delete.
(Z_packet_to_bkpt_type, Z_packet_to_raw_bkpt_type): New functions.
(find_gdb_breakpoint): New function.
(set_gdb_breakpoint_at): Delete.
(z_type_supported): New function.
(set_gdb_breakpoint_1): New function, loosely based off
set_gdb_breakpoint_at.
(check_gdb_bp_preconditions, set_gdb_breakpoint): New functions.
(delete_gdb_breakpoint_at): Delete.
(delete_gdb_breakpoint_1): New function, loosely based off
delete_gdb_breakpoint_at.
(delete_gdb_breakpoint): New function.
(clear_gdb_breakpoint_conditions): Rename to ...
(clear_breakpoint_conditions): ... this. Don't handle a NULL
breakpoint.
(add_condition_to_breakpoint): Make static.
(add_breakpoint_condition): Take a struct breakpoint pointer
instead of an address. Adjust.
(gdb_condition_true_at_breakpoint): Rename to ...
(gdb_condition_true_at_breakpoint_z_type): ... this, and add
z_type parameter.
(gdb_condition_true_at_breakpoint): Reimplement.
(add_breakpoint_commands): Take a struct breakpoint pointer
instead of an address. Adjust.
(gdb_no_commands_at_breakpoint): Rename to ...
(gdb_no_commands_at_breakpoint_z_type): ... this. Add z_type
parameter. Return true if no breakpoint was found. Change debug
output.
(gdb_no_commands_at_breakpoint): Reimplement.
(run_breakpoint_commands): Rename to ...
(run_breakpoint_commands_z_type): ... this. Add z_type parameter,
and change return type to boolean.
(run_breakpoint_commands): New function.
(gdb_breakpoint_here): Also check for Z1 breakpoints.
(uninsert_raw_breakpoint): Don't try to reinsert a disabled
breakpoint. Go through the_target->remove_point instead of
assuming memory breakpoint.
(uninsert_breakpoints_at, uninsert_all_breakpoints): Uninsert
software and hardware breakpoints.
(reinsert_raw_breakpoint): Go through the_target->insert_point
instead of assuming memory breakpoint.
(reinsert_breakpoints_at, reinsert_all_breakpoints): Reinsert
software and hardware breakpoints.
(check_breakpoints, breakpoint_here, breakpoint_inserted_here):
Check both software and hardware breakpoints.
(validate_inserted_breakpoint): Assert the breakpoint is a
software breakpoint. Set the inserted flag to -1 instead of
setting shlib_disabled.
(delete_disabled_breakpoints): Adjust.
(validate_breakpoints): Only validate software breakpoints.
Adjust to inserted flag change.
(check_mem_read, check_mem_write): Skip breakpoint types other
than software breakpoints. Adjust to inserted flag change.
* mem-break.h (enum raw_bkpt_type): New enum.
(raw_breakpoint, struct process_info): Forward declare.
(Z_packet_to_target_hw_bp_type): Delete declaration.
(raw_bkpt_type_to_target_hw_bp_type, Z_packet_to_raw_bkpt_type)
(set_gdb_breakpoint, delete_gdb_breakpoint)
(clear_breakpoint_conditions): New declarations.
(set_gdb_breakpoint_at, clear_gdb_breakpoint_conditions): Delete.
(breakpoint_inserted_here): Update comment.
(add_breakpoint_condition, add_breakpoint_commands): Replace
address parameter with a breakpoint pointer parameter.
(gdb_breakpoint_here): Update comment.
(delete_gdb_breakpoint_at): Delete.
(insert_memory_breakpoint, remove_memory_breakpoint): Declare.
* server.c (process_point_options): Take a struct breakpoint
pointer instead of an address. Adjust.
(process_serial_event) <Z/z packets>: Use set_gdb_breakpoint and
delete_gdb_breakpoint.
* spu-low.c (spu_target_ops): Install NULL as
supports_z_point_type method.
* target.h: Include mem-break.h.
(struct target_ops) <prepare_to_access_memory>: Update comment.
<supports_z_point_type>: New field.
<insert_point, remove_point>: Take an enum raw_bkpt_type argument
instead of a char. Also take a raw breakpoint pointer.
* win32-arm-low.c (the_low_target): Install NULL as
supports_z_point_type.
* win32-i386-low.c (i386_supports_z_point_type): New function.
(i386_insert_point, i386_remove_point): Adjust to new interface.
(the_low_target): Install i386_supports_z_point_type.
* win32-low.c (win32_supports_z_point_type): New function.
(win32_insert_point, win32_remove_point): Adjust to new interface.
(win32_target_ops): Install win32_supports_z_point_type.
* win32-low.h (struct win32_target_ops):
<supports_z_point_type>: New method.
<insert_point, remove_point>: Take an enum raw_bkpt_type argument
instead of a char. Also take a raw breakpoint pointer.
gdb/testsuite/
2014-05-20 Pedro Alves <palves@redhat.com>
* gdb.base/break-idempotent.c: New file.
* gdb.base/break-idempotent.exp: New file.
The Aarch64, MIPS and x86 Linux backends all have Z packet number
defines and corresponding protocol number to internal type convertion
routines. Factor them all out to gdbserver's core code, so we only
have one shared copy.
Tested on x86_64 Fedora 20, and also cross built for aarch64-linux-gnu
and mips-linux-gnu.
gdb/gdbserver/
2014-05-20 Pedro Alves <palves@redhat.com>
* mem-break.h: Include break-common.h.
(Z_PACKET_SW_BP, Z_PACKET_HW_BP, Z_PACKET_WRITE_WP)
(Z_PACKET_READ_WP, Z_PACKET_ACCESS_WP): New defines.
(Z_packet_to_target_hw_bp_type): New declaration.
* mem-break.c (Z_packet_to_target_hw_bp_type): New function.
* i386-low.c (Z_PACKET_HW_BP, Z_PACKET_WRITE_WP, Z_PACKET_READ_WP)
(Z_PACKET_ACCESS_WP): Delete macros.
(Z_packet_to_hw_type): Delete function.
* i386-low.h: Don't include break-common.h here.
(Z_packet_to_hw_type): Delete declaration.
* linux-x86-low.c (x86_insert_point, x86_insert_point): Call
Z_packet_to_target_hw_bp_type instead of Z_packet_to_hw_type.
* win32-i386-low.c (i386_insert_point, i386_remove_point): Call
Z_packet_to_target_hw_bp_type instead of Z_packet_to_hw_type.
* linux-aarch64-low.c: Don't include break-common.h here.
(Z_PACKET_SW_BP, Z_PACKET_HW_BP, Z_PACKET_WRITE_WP)
(Z_PACKET_READ_WP, Z_PACKET_ACCESS_WP): Delete macros.
(Z_packet_to_target_hw_bp_type): Delete function.
* linux-mips-low.c (rsp_bp_type_to_target_hw_bp_type): Delete
function.
(mips_insert_point, mips_remove_point): Use
Z_packet_to_target_hw_bp_type.
This makes linux-aarch64-low.c use target_hw_bp_type, like gdb's
aarch64-linux-nat.c. The original motivation is decoupling
insert_point/remove_point from Z packet numbers, but I think making
the files a little bit more similar is a good thing on its own right.
Ideally we'd merge these files even... The
aarch64_point_encode_ctrl_reg change is taken straight from GDB's
copy.
I confirmed with a cross compiler that this builds, but it's otherwise
untested.
gdb/gdbserver/
2014-05-20 Pedro Alves <palves@redhat.com>
* linux-aarch64-low.c: Include break-common.h.
(enum target_point_type): Delete.
(Z_packet_to_point_type): Rename to ...
(Z_packet_to_target_hw_bp_type): ... this, and return a
target_hw_bp_type instead.
(aarch64_show_debug_reg_state): Take an enum target_hw_bp_type
instead of an enum target_point_type.
(aarch64_point_encode_ctrl_reg): Likewise. Compute type mask from
breakpoint type.
(aarch64_dr_state_insert_one_point)
(aarch64_dr_state_remove_one_point, aarch64_handle_breakpoint)
(aarch64_handle_aligned_watchpoint)
(aarch64_handle_unaligned_watchpoint, aarch64_handle_watchpoint):
Take an enum target_hw_bp_type instead of an enum
target_point_type.
(aarch64_supports_z_point_type): New function.
(aarch64_insert_point, aarch64_remove_point): Use it. Adjust to
use Z_packet_to_target_hw_bp_type.
* aarch64-linux-nat.c (aarch64_linux_set_debug_regs): Set
iov.iov_len with the real length in use.
gdb/gdbserver/
* linux-aarch64-low.c (aarch64_linux_set_debug_regs): Set
iov.iov_len with the real length in use.
Apply the same fix that was applied to aarch64-linux-nat.c.
2013-09-16 Will Newton <will.newton@linaro.org>
* linux-aarch64-low.c (aarch64_linux_set_debug_regs): Zero
out regs.
This patch makes GDBserver support multi-process + biarch.
Currently, if you're debugging more than one process at once with a
single gdbserver (in extended-remote mode), then all processes must
have the same architecture (e.g., 64-bit vs 32-bit). Otherwise, you
see this:
Added inferior 2
[Switching to inferior 2 [<null>] (<noexec>)]
Reading symbols from /home/pedro/gdb/tests/main32...done.
Temporary breakpoint 2 at 0x4004cf: main. (2 locations)
Starting program: /home/pedro/gdb/tests/main32
warning: Selected architecture i386 is not compatible with reported target architecture i386:x86-64
warning: Architecture rejected target-supplied description
Remote 'g' packet reply is too long: 000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000090cfffff0000000000000000000000000000000000000000000000000000000000020000000000000000000000000000000000000000000000000000000000000000000000000000b042f7460000000000020000230000002b0000002b0000002b000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000007f03000000000000ffff0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000801f00003b0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000
... etc, etc ...
Even though the process was running a 32-bit program, GDBserver sent
back to GDB a register set in 64-bit layout.
A patch (http://sourceware.org/ml/gdb-patches/2012-11/msg00228.html) a
while ago made GDB track a target_gdbarch per inferior, and as
consequence, fetch a target description per-inferior. This patch is
the GDBserver counterpart, that makes GDBserver keep track of each
process'es XML target description and register layout. So in the
example above, GDBserver will send the correct register set in 32-bit
layout to GDB.
A new "struct target_desc" object (tdesc for short) is added, that
holds the target description and register layout information about
each process. Each `struct process_info' holds a pointer to a target
description. The regcache also gains a pointer to a target
description, mainly for convenience, and parallel with GDB (and
possible future support for programs that flip processor modes).
The low target's arch_setup routines are responsible for setting the
process'es correct tdesc. This isn't that much different to how
things were done before, except that instead of detecting the inferior
process'es architecture and calling the corresponding
init_registers_FOO routine, which would change the regcache layout
globals and recreate the threads' regcaches, the regcache.c globals
are gone, and the init_registers_$BAR routines now each initialize a
separate global struct target_desc object (one for each arch variant
GDBserver supports), and so all the init_registers_$BAR routines that
are built into GDBserver are called early at GDBserver startup time
(similarly to how GDB handles its built-in target descriptions), and
then the arch_setup routine is responsible for making
process_info->tdesc point to one of these target description globals.
The regcache module is all parameterized to get the regcache's layout
from the tdesc object instead of the old register_bytes, etc. globals.
The threads' regcaches are now created lazily. The old scheme where
we created each of them when we added a new thread doesn't work
anymore, because we add the main thread/lwp before we see it stop for
the first time, and it is only when we see the thread stop for the
first time that we have a chance of determining the inferior's
architecture (through the_low_target.arch_setup). Therefore when we
add the main thread we don't know which architecture/tdesc its
regcache should have.
This patch makes the gdb.multi/multi-arch.exp test now pass against
(extended-remote) GDBserver. It currently fails, without this patch.
The IPA also uses the regcache, so it gains a new global struct
target_desc pointer, which points at the description of the process it
is loaded in.
Re. the linux-low.c & friends changes. Since the register map
etc. may differ between processes (64-bit vs 32-bit) etc., the
linux_target_ops num_regs, regmap and regset_bitmap data fields are no
longer sufficient. A new method is added in their place that returns
a pointer to a new struct that includes all info linux-low.c needs to
access registers of the current inferior.
The patch/discussion that originally introduced
linux-low.c:disabled_regsets mentions that the disabled_regsets set
may be different per mode (in a biarch setup), and indeed that is
cleared whenever we start a new (first) inferior, so that global is
moved as well behind the new `struct regs_info'.
On the x86 side:
I simply replaced the i387-fp.c:num_xmm_registers global with a check
for 64-bit or 32-bit process, which is equivalent to how the global
was set. This avoided coming up with some more general mechanism that
would work for all targets that use this module (GNU/Linux, Windows,
etc.).
Tested:
GNU/Linux IA64
GNU/Linux MIPS64
GNU/Linux PowerPC (Fedora 16)
GNU/Linux s390x (Fedora 16)
GNU/Linux sparc64 (Debian)
GNU/Linux x86_64, -m64 and -m32 (Fedora 17)
Cross built, and smoke tested:
i686-w64-mingw32, under Wine.
GNU/Linux TI C6x, by Yao Qi.
Cross built but otherwise not tested:
aarch64-linux-gnu
arm-linux-gnu
m68k-linux
nios2-linux-gnu
sh-linux-gnu
spu
tilegx-unknown-linux-gnu
Completely untested:
GNU/Linux Blackfin
GNU/Linux CRIS
GNU/Linux CRISv32
GNU/Linux TI Xtensa
GNU/Linux M32R
LynxOS
QNX NTO
gdb/gdbserver/
2013-06-07 Pedro Alves <palves@redhat.com>
* Makefile.in (OBS): Add tdesc.o.
(IPA_OBJS): Add tdesc-ipa.o.
(tdesc-ipa.o): New rule.
* ax.c (gdb_eval_agent_expr): Adjust register_size call to new
interface.
* linux-low.c (new_inferior): Delete.
(disabled_regsets, num_regsets): Delete.
(linux_add_process): Adjust to set the new per-process
new_inferior flag.
(linux_detach_one_lwp): Adjust to call regcache_invalidate_thread.
(linux_wait_for_lwp): Adjust. Only call arch_setup if the event
was a stop. When calling arch_setup, switch the current inferior
to the thread that got an event.
(linux_resume_one_lwp): Adjust to call regcache_invalidate_thread.
(regsets_fetch_inferior_registers)
(regsets_store_inferior_registers): New regsets_info parameter.
Adjust to use it.
(linux_register_in_regsets): New regs_info parameter. Adjust to
use it.
(register_addr, fetch_register, store_register): New usrregs_info
parameter. Adjust to use it.
(usr_fetch_inferior_registers, usr_store_inferior_registers): New
parameter regs_info. Adjust to use it.
(linux_fetch_registers): Get the current inferior's regs_info, and
adjust to use it.
(linux_store_registers): Ditto.
[HAVE_LINUX_REGSETS] (initialize_regsets_info): New.
(initialize_low): Don't initialize the target_regsets here. Call
initialize_low_arch.
* linux-low.h (target_regsets): Delete declaration.
(struct regsets_info): New.
(struct usrregs_info): New.
(struct regs_info): New.
(struct process_info_private) <new_inferior>: New field.
(struct linux_target_ops): Delete the num_regs, regmap, and
regset_bitmap fields. New field regs_info.
[HAVE_LINUX_REGSETS] (initialize_regsets_info): Declare.
* i387-fp.c (num_xmm_registers): Delete.
(i387_cache_to_fsave, i387_fsave_to_cache): Adjust find_regno
calls to new interface.
(i387_cache_to_fxsave, i387_cache_to_xsave, i387_fxsave_to_cache)
(i387_xsave_to_cache): Adjust find_regno calls to new interface.
Infer the number of xmm registers from the regcache's target
description.
* i387-fp.h (num_xmm_registers): Delete.
* inferiors.c (add_thread): Don't install the thread's regcache
here.
* proc-service.c (gregset_info): Fetch the current inferior's
regs_info. Adjust to use it.
* regcache.c: Include tdesc.h.
(register_bytes, reg_defs, num_registers)
(gdbserver_expedite_regs): Delete.
(get_thread_regcache): If the thread doesn't have a regcache yet,
create one, instead of aborting gdbserver.
(regcache_invalidate_one): Rename to ...
(regcache_invalidate_thread): ... this.
(regcache_invalidate_one): New.
(regcache_invalidate): Only invalidate registers of the current
process.
(init_register_cache): Add target_desc parameter, and use it.
(new_register_cache): Ditto. Assert the target description has a
non zero registers_size.
(regcache_cpy): Add assertions. Adjust.
(realloc_register_cache, set_register_cache): Delete.
(registers_to_string, registers_from_string): Adjust.
(find_register_by_name, find_regno, find_register_by_number)
(register_cache_size): Add target_desc parameter, and use it.
(free_register_cache_thread, free_register_cache_thread_one)
(regcache_release, register_cache_size): New.
(register_size): Add target_desc parameter, and use it.
(register_data, supply_register, supply_register_zeroed)
(supply_regblock, supply_register_by_name, collect_register)
(collect_register_as_string, collect_register_by_name): Adjust.
* regcache.h (struct target_desc): Forward declare.
(struct regcache) <tdesc>: New field.
(init_register_cache, new_register_cache): Add target_desc
parameter.
(regcache_invalidate_thread): Declare.
(regcache_invalidate_one): Delete declaration.
(regcache_release): Declare.
(find_register_by_number, register_cache_size, register_size)
(find_regno): Add target_desc parameter.
(gdbserver_expedite_regs, gdbserver_xmltarget): Delete
declarations.
* remote-utils.c: Include tdesc.h.
(outreg, prepare_resume_reply): Adjust.
* server.c: Include tdesc.h.
(gdbserver_xmltarget): Delete declaration.
(get_features_xml, process_serial_event): Adjust.
* server.h [IN_PROCESS_AGENT] (struct target_desc): Forward
declare.
(struct process_info) <tdesc>: New field.
(ipa_tdesc): Declare.
* tdesc.c: New file.
* tdesc.h: New file.
* tracepoint.c: Include tdesc.h.
[IN_PROCESS_AGENT] (ipa_tdesc): Define.
(get_context_regcache): Adjust to pass ipa_tdesc down.
(do_action_at_tracepoint): Adjust to get the register cache size
from the context regcache's description.
(traceframe_walk_blocks): Adjust to get the register cache size
from the current trace frame's description.
(traceframe_get_pc): Adjust to get current trace frame's
description and pass it down.
(gdb_collect): Adjust to get the register cache size from the
IPA's description.
* linux-amd64-ipa.c (tdesc_amd64_linux): Declare.
(gdbserver_xmltarget): Delete.
(initialize_low_tracepoint): Set the ipa's target description.
* linux-i386-ipa.c (tdesc_i386_linux): Declare.
(initialize_low_tracepoint): Set the ipa's target description.
* linux-x86-low.c: Include tdesc.h.
[__x86_64__] (is_64bit_tdesc): New.
(ps_get_thread_area, x86_get_thread_area): Use it.
(i386_cannot_store_register): Rename to ...
(x86_cannot_store_register): ... this. Use is_64bit_tdesc.
(i386_cannot_fetch_register): Rename to ...
(x86_cannot_fetch_register): ... this. Use is_64bit_tdesc.
(x86_fill_gregset, x86_store_gregset): Adjust register_size calls
to new interface.
(target_regsets): Rename to ...
(x86_regsets): ... this.
(x86_get_pc, x86_set_pc): Adjust register_size calls to new
interface.
(x86_siginfo_fixup): Use is_64bit_tdesc.
[__x86_64__] (tdesc_amd64_linux, tdesc_amd64_avx_linux)
(tdesc_x32_avx_linux, tdesc_x32_linux)
(tdesc_i386_linux, tdesc_i386_mmx_linux, tdesc_i386_avx_linux):
Declare.
(x86_linux_update_xmltarget): Delete.
(I386_LINUX_XSAVE_XCR0_OFFSET): Define.
(have_ptrace_getfpxregs, have_ptrace_getregset): New.
(AMD64_LINUX_USER64_CS): New.
(x86_linux_read_description): New, based on
x86_linux_update_xmltarget.
(same_process_callback): New.
(x86_arch_setup_process_callback): New.
(x86_linux_update_xmltarget): New.
(x86_regsets_info): New.
(amd64_linux_regs_info): New.
(i386_linux_usrregs_info): New.
(i386_linux_regs_info): New.
(x86_linux_regs_info): New.
(x86_arch_setup): Reimplement.
(x86_install_fast_tracepoint_jump_pad): Use is_64bit_tdesc.
(x86_emit_ops): Ditto.
(the_low_target): Adjust. Install x86_linux_regs_info,
x86_cannot_fetch_register, and x86_cannot_store_register.
(initialize_low_arch): New.
* linux-ia64-low.c (tdesc_ia64): Declare.
(ia64_fetch_register): Adjust.
(ia64_usrregs_info, regs_info): New globals.
(ia64_regs_info): New function.
(the_low_target): Adjust.
(initialize_low_arch): New function.
* linux-sparc-low.c (tdesc_sparc64): Declare.
(sparc_fill_gregset_to_stack, sparc_store_gregset_from_stack):
Adjust.
(sparc_arch_setup): New function.
(sparc_regsets_info, sparc_usrregs_info, regs_info): New globals.
(the_low_target): Adjust.
(initialize_low_arch): New function.
* linux-ppc-low.c (tdesc_powerpc_32l, tdesc_powerpc_altivec32l)
(tdesc_powerpc_cell32l, tdesc_powerpc_vsx32l)
(tdesc_powerpc_isa205_32l, tdesc_powerpc_isa205_altivec32l)
(tdesc_powerpc_isa205_vsx32l, tdesc_powerpc_e500l)
(tdesc_powerpc_64l, tdesc_powerpc_altivec64l)
(tdesc_powerpc_cell64l, tdesc_powerpc_vsx64l)
(tdesc_powerpc_isa205_64l, tdesc_powerpc_isa205_altivec64l)
(tdesc_powerpc_isa205_vsx64l): Declare.
(ppc_cannot_store_register, ppc_collect_ptrace_register)
(ppc_supply_ptrace_register, parse_spufs_run, ppc_get_pc)
(ppc_set_pc, ppc_get_hwcap): Adjust.
(ppc_usrregs_info): Forward declare.
(!__powerpc64__) ppc_regmap_adjusted: New global.
(ppc_arch_setup): Adjust to the current process'es target
description.
(ppc_fill_vsxregset, ppc_store_vsxregset, ppc_fill_vrregset)
(ppc_store_vrregset, ppc_fill_evrregset, ppc_store_evrregse)
(ppc_store_evrregset): Adjust.
(target_regsets): Rename to ...
(ppc_regsets): ... this, and make static.
(ppc_usrregs_info, ppc_regsets_info, regs_info): New globals.
(ppc_regs_info): New function.
(the_low_target): Adjust.
(initialize_low_arch): New function.
* linux-s390-low.c (tdesc_s390_linux32, tdesc_s390_linux32v1)
(tdesc_s390_linux32v2, tdesc_s390_linux64, tdesc_s390_linux64v1)
(tdesc_s390_linux64v2, tdesc_s390x_linux64, tdesc_s390x_linux64v1)
(tdesc_s390x_linux64v2): Declare.
(s390_collect_ptrace_register, s390_supply_ptrace_register)
(s390_fill_gregset, s390_store_last_break): Adjust.
(target_regsets): Rename to ...
(s390_regsets): ... this, and make static.
(s390_get_pc, s390_set_pc): Adjust.
(s390_get_hwcap): New target_desc parameter, and use it.
[__s390x__] (have_hwcap_s390_high_gprs): New global.
(s390_arch_setup): Adjust to set the current process'es target
description. Don't adjust the regmap.
(s390_usrregs_info, s390_regsets_info, regs_info): New globals.
[__s390x__] (s390_usrregs_info_3264, s390_regsets_info_3264)
(regs_info_3264): New globals.
(s390_regs_info): New function.
(the_low_target): Adjust.
(initialize_low_arch): New function.
* linux-mips-low.c (tdesc_mips_linux, tdesc_mips_dsp_linux)
(tdesc_mips64_linux, tdesc_mips64_dsp_linux): Declare.
[__mips64] (init_registers_mips_linux)
(init_registers_mips_dsp_linux): Delete defines.
[__mips64] (tdesc_mips_linux, tdesc_mips_dsp_linux): New defines.
(have_dsp): New global.
(mips_read_description): New, based on mips_arch_setup.
(mips_arch_setup): Reimplement.
(get_usrregs_info): New function.
(mips_cannot_fetch_register, mips_cannot_store_register)
(mips_get_pc, mips_set_pc, mips_fill_gregset, mips_store_gregset)
(mips_fill_fpregset, mips_store_fpregset): Adjust.
(target_regsets): Rename to ...
(mips_regsets): ... this, and make static.
(mips_regsets_info, mips_dsp_usrregs_info, mips_usrregs_info)
(dsp_regs_info, regs_info): New globals.
(mips_regs_info): New function.
(the_low_target): Adjust.
(initialize_low_arch): New function.
* linux-arm-low.c (tdesc_arm, tdesc_arm_with_iwmmxt)
(tdesc_arm_with_vfpv2, tdesc_arm_with_vfpv3, tdesc_arm_with_neon):
Declare.
(arm_fill_vfpregset, arm_store_vfpregset): Adjust.
(arm_read_description): New, with bits factored from
arm_arch_setup.
(arm_arch_setup): Reimplement.
(target_regsets): Rename to ...
(arm_regsets): ... this, and make static.
(arm_regsets_info, arm_usrregs_info, regs_info): New globals.
(arm_regs_info): New function.
(the_low_target): Adjust.
(initialize_low_arch): New function.
* linux-m68k-low.c (tdesc_m68k): Declare.
(target_regsets): Rename to ...
(m68k_regsets): ... this, and make static.
(m68k_regsets_info, m68k_usrregs_info, regs_info): New globals.
(m68k_regs_info): New function.
(m68k_arch_setup): New function.
(the_low_target): Adjust.
(initialize_low_arch): New function.
* linux-sh-low.c (tdesc_sharch): Declare.
(target_regsets): Rename to ...
(sh_regsets): ... this, and make static.
(sh_regsets_info, sh_usrregs_info, regs_info): New globals.
(sh_regs_info, sh_arch_setup): New functions.
(the_low_target): Adjust.
(initialize_low_arch): New function.
* linux-bfin-low.c (tdesc_bfin): Declare.
(bfin_arch_setup): New function.
(bfin_usrregs_info, regs_info): New globals.
(bfin_regs_info): New function.
(the_low_target): Adjust.
(initialize_low_arch): New function.
* linux-cris-low.c (tdesc_cris): Declare.
(cris_arch_setup): New function.
(cris_usrregs_info, regs_info): New globals.
(cris_regs_info): New function.
(the_low_target): Adjust.
(initialize_low_arch): New function.
* linux-cris-low.c (tdesc_crisv32): Declare.
(cris_arch_setup): New function.
(cris_regsets_info, cris_usrregs_info, regs_info): New globals.
(cris_regs_info): New function.
(the_low_target): Adjust.
(initialize_low_arch): New function.
* linux-m32r-low.c (tdesc_m32r): Declare.
(m32r_arch_setup): New function.
(m32r_usrregs_info, regs_info): New globals.
(m32r_regs_info): Adjust.
(initialize_low_arch): New function.
* linux-tic6x-low.c (tdesc_tic6x_c64xp_linux)
(tdesc_tic6x_c64x_linux, tdesc_tic6x_c62x_linux): Declare.
(tic6x_usrregs_info): Forward declare.
(tic6x_read_description): New function, based on ...
(tic6x_arch_setup): ... this. Reimplement.
(target_regsets): Rename to ...
(tic6x_regsets): ... this, and make static.
(tic6x_regsets_info, tic6x_usrregs_info, regs_info): New globals.
(tic6x_regs_info): New function.
(the_low_target): Adjust.
(initialize_low_arch): New function.
* linux-xtensa-low.c (tdesc_xtensa): Declare.
(xtensa_fill_gregset, xtensa_store_gregset): Adjust.
(target_regsets): Rename to ...
(xtensa_regsets): ... this, and make static.
(xtensa_regsets_info, xtensa_usrregs_info, regs_info): New
globals.
(xtensa_arch_setup, xtensa_regs_info): New functions.
(the_low_target): Adjust.
(initialize_low_arch): New function.
* linux-nios2-low.c (tdesc_nios2_linux): Declare.
(nios2_arch_setup): Set the current process'es tdesc.
(target_regsets): Rename to ...
(nios2_regsets): ... this.
(nios2_regsets_info, nios2_usrregs_info, regs_info): New globals.
(nios2_regs_info): New function.
(the_low_target): Adjust.
(initialize_low_arch): New function.
* linux-aarch64-low.c (tdesc_aarch64): Declare.
(aarch64_arch_setup): Set the current process'es tdesc.
(target_regsets): Rename to ...
(aarch64_regsets): ... this.
(aarch64_regsets_info, aarch64_usrregs_info, regs_info): New globals.
(aarch64_regs_info): New function.
(the_low_target): Adjust.
(initialize_low_arch): New function.
* linux-tile-low.c (tdesc_tilegx, tdesc_tilegx32): Declare
globals.
(target_regsets): Rename to ...
(tile_regsets): ... this.
(tile_regsets_info, tile_usrregs_info, regs_info): New globals.
(tile_regs_info): New function.
(tile_arch_setup): Set the current process'es tdesc.
(the_low_target): Adjust.
(initialize_low_arch): New function.
* spu-low.c (tdesc_spu): Declare.
(spu_create_inferior, spu_attach): Set the new process'es tdesc.
* win32-arm-low.c (tdesc_arm): Declare.
(arm_arch_setup): New function.
(the_low_target): Install arm_arch_setup instead of
init_registers_arm.
* win32-i386-low.c (tdesc_i386, tdesc_amd64): Declare.
(init_windows_x86): Rename to ...
(i386_arch_setup): ... this. Set `win32_tdesc'.
(the_low_target): Adjust.
* win32-low.c (win32_tdesc): New global.
(child_add_thread): Don't create the thread cache here.
(do_initial_child_stuff): Set the new process'es tdesc.
* win32-low.h (struct target_desc): Forward declare.
(win32_tdesc): Declare.
* lynx-i386-low.c (tdesc_i386): Declare global.
(lynx_i386_arch_setup): Set `lynx_tdesc'.
* lynx-low.c (lynx_tdesc): New global.
(lynx_add_process): Set the new process'es tdesc.
* lynx-low.h (struct target_desc): Forward declare.
(lynx_tdesc): Declare global.
* lynx-ppc-low.c (tdesc_powerpc_32): Declare global.
(lynx_ppc_arch_setup): Set `lynx_tdesc'.
* nto-low.c (nto_tdesc): New global.
(do_attach): Set the new process'es tdesc.
* nto-low.h (struct target_desc): Forward declare.
(nto_tdesc): Declare.
* nto-x86-low.c (tdesc_i386): Declare.
(nto_x86_arch_setup): Set `nto_tdesc'.
gdb/
2013-06-07 Pedro Alves <palves@redhat.com>
* regformats/regdat.sh: Output #include tdesc.h. Make globals
static. Output a global target description pointer.
(init_registers_${name}): Adjust to initialize a
target description structure.
The GDBserver Aarch64 port includes the aarch64-without-fpu
description in the build, but doesn't actually use it anywhere. As
Linux always requires an FPU, just remove the dead code.
gdb/gdbserver/
2013-05-28 Pedro Alves <palves@redhat.com>
* Makefile.in (clean): Remove reference to aarch64-without-fpu.c.
(aarch64-without-fpu.c): Delete rule.
* configure.srv (aarch64*-*-linux*): Remove references to
aarch64-without-fpu.o and aarch64-without-fpu.xml.
* linux-aarch64-low.c (init_registers_aarch64_without_fpu): Remove
declaration.
Yao Qi
Simon Marchi
Pedro Alves
Pierre Langlois
Don Breazeal
Gary Benson
Joel Brobecker
Catalin Udma
Ramana Radhakrishnan
Doug Evans
Yufeng Zhang
Will Newton