Since multi_line was moved to gdb.exp in a slightly stricter form,
The gdb.ada/info_exc.exp:info exceptions test has been failing.
This is because it now expects a new-line sequence at the end of
each argument given to multi_line, including ".*". But the intent
when writing the test was to signify "could-be-nothing-at-all".
As a result, the test fails on x86_64-linux with a runtime built as
recommended, because of that
extra new-line sequence.
gdb/testsuite/ChangeLog:
* gdb.ada/info_exc.exp: Adjust "info exceptions" expected output.
This patch is to fix two ARI warnings for nat/aarch64-linux-hw-point.{c,h}.
gdb:
2015-07-20 Yao Qi <yao.qi@linaro.org>
* nat/aarch64-linux-hw-point.c (aarch64_handle_unaligned_watchpoint):
Re-indent the code.
* nat/aarch64-linux-hw-point.h: Use ULONGEST rather than
"unsigned long long".
GDB already allows statically initialized variables, located in
SEC_LOAD sections, to be placed at address 0. This change allows
uninitialized variables (which are in SEC_ALLOC sections) to be placed
address 0 as well.
gdb/ChangeLog:
* dwarf2read.c (dwarf2_locate_sections): Allow has_section_at_zero
to be set for SEC_ALLOC sections too.
When I look at test fails related to watchpoint on aarch64-linux,
I find there are some code duplicates between GDB and GDBserver.
This patch is to move some of them to a nat/aarch64-linux-hw-point.{h,c}.
The only change I do is about the dr_changed_t typedef, which was
ULONGEST in GDB and 'unsigned long long' in GDBserver. Each bit
of dr_changed_t represents a status of each HW breakpoint or
watchpoint register, and the max number of HW breakpoint or watchpoint
registers is 16, so the width of 'unsigned long long' is sufficient.
gdb:
2015-07-17 Yao Qi <yao.qi@linaro.org>
* Makefile.in (HFILES_NO_SRCDIR): Add
nat/aarch64-linux-hw-point.h.
(aarch64-linux-hw-point.o): New rule.
* nat/aarch64-linux-hw-point.h: New file.
* nat/aarch64-linux-hw-point.c: New file.
* aarch64-linux-nat.c: Include nat/aarch64-linux-hw-point.h.
(AARCH64_HBP_MAX_NUM): Move to nat/aarch64-linux-hw-point.h.
(AARCH64_HWP_MAX_NUM, AARCH64_HBP_ALIGNMENT): Likewise.
(AARCH64_HWP_ALIGNMENT): Likewise.
(AARCH64_HWP_MAX_LEN_PER_REG): Likewise.
(AARCH64_DEBUG_NUM_SLOTS, AARCH64_DEBUG_ARCH): Likewise.
(AARCH64_DEBUG_ARCH_V8, DR_MARK_ALL_CHANGED): Likewise.
(DR_MARK_N_CHANGED, DR_CLEAR_CHANGED): Likewise.
(DR_HAS_CHANGED, DR_N_HAS_CHANGE): Likewise.
(aarch64_num_bp_regs, aarch64_num_wp_regs): Likewise.
(struct aarch64_debug_reg_state): Likewise.
(struct arch_lwp_info): Likewise.
(aarch64_linux_set_debug_regs): Likewise.
(aarch64_notify_debug_reg_change): Remove static.
(aarch64_align_watchpoint): Likewise.
(DR_CONTROL_ENABLED, DR_CONTROL_LENGTH): Likewise.
(aarch64_watchpoint_length): Likewise.
(aarch64_point_encode_ctrl_reg): Likewise
(aarch64_point_is_aligned): Likewise.
(aarch64_dr_state_insert_one_point): Likewise.
(aarch64_dr_state_remove_one_point): Likewise.
(aarch64_handle_breakpoint): Likewise.
(aarch64_handle_aligned_watchpoint): Likewise.
(aarch64_handle_unaligned_watchpoint): Likewise.
(aarch64_handle_watchpoint): Likewise.
* config/aarch64/linux.mh (NAT_FILE): Add
aarch64-linux-hw-point.o.
gdb/gdbserver:
2015-07-17 Yao Qi <yao.qi@linaro.org>
* Makefile.in (aarch64-linux-hw-point.o): New rule.
* configure.srv (srv_tgtobj): Append aarch64-linux-hw-point.o.
* linux-aarch64-low.c: Include nat/aarch64-linux-hw-point.h.
(AARCH64_HBP_MAX_NUM): Move to nat/aarch64-linux-hw-point.h.
(AARCH64_HWP_MAX_NUM, AARCH64_HBP_ALIGNMENT): Likewise.
(AARCH64_HWP_ALIGNMENT): Likewise.
(AARCH64_HWP_MAX_LEN_PER_REG): Likewise.
(AARCH64_DEBUG_NUM_SLOTS, AARCH64_DEBUG_ARCH): Likewise.
(aarch64_num_bp_regs, aarch64_num_wp_regs): Likewise.
(AARCH64_DEBUG_ARCH_V8, DR_MARK_ALL_CHANGED): Likewise.
(DR_MARK_N_CHANGED, DR_CLEAR_CHANGED): Likewise.
(DR_HAS_CHANGED, DR_N_HAS_CHANGE): Likewise.
(struct aarch64_debug_reg_state): Likewise.
(struct arch_lwp_info): Likewise.
(aarch64_align_watchpoint): Likewise.
(DR_CONTROL_ENABLED, DR_CONTROL_LENGTH): Likewise.
(aarch64_watchpoint_length): Likewise.
(aarch64_point_encode_ctrl_reg): Likewise
(aarch64_point_is_aligned): Likewise.
(aarch64_align_watchpoint): Likewise.
(aarch64_linux_set_debug_regs):
(aarch64_dr_state_insert_one_point): Likewise.
(aarch64_dr_state_remove_one_point): Likewise.
(aarch64_handle_breakpoint): Likewise.
(aarch64_handle_aligned_watchpoint): Likewise.
(aarch64_handle_unaligned_watchpoint): Likewise.
(aarch64_handle_watchpoint): Likewise.
Some functions on handling HW watchpoint in GDB and GDBserver looks the
same except the code getting debug register state from current inferior.
In GDB, we get debug register state like this:
state = aarch64_get_debug_reg_state (ptid_get_pid (inferior_ptid));
while in GDBserver, we get debug register state like this:
state = aarch64_get_debug_reg_state ();
This patch is to move two lines above out of some functions, and pass
aarch64_debug_reg_state to these functions, in this way, these functions
are the same, and can be moved to a common place.
gdb:
2015-07-17 Yao Qi <yao.qi@linaro.org>
* aarch64-linux-nat.c (aarch64_handle_breakpoint): Add argument
state and don't call aarch64_get_debug_reg_state. All callers
update.
(aarch64_linux_insert_hw_breakpoint): Call
aarch64_get_debug_reg_state earlier.
(aarch64_linux_remove_hw_breakpoint): Likewise.
(aarch64_handle_aligned_watchpoint): Add argument state and
don't call aarch64_get_debug_reg_state. All callers update.
(aarch64_handle_unaligned_watchpoint): Likewise.
(aarch64_handle_watchpoint): Add argument state.
(aarch64_linux_insert_watchpoint): Call aarch64_get_debug_reg_state
earlier.
(aarch64_linux_remove_watchpoint): Likewise.
gdb/gdbserver:
2015-07-17 Yao Qi <yao.qi@linaro.org>
* linux-aarch64-low.c (aarch64_handle_breakpoint): Add argument state
and don't aarch64_get_debug_reg_state. All callers update.
(aarch64_handle_aligned_watchpoint): Likewise.
(aarch64_handle_unaligned_watchpoint): Likewise.
(aarch64_handle_watchpoint): Likewise.
(aarch64_insert_point): Call aarch64_get_debug_reg_state earlier.
(aarch64_remove_point): Likewise.
Some functions in aarch64-linux-nat.c and linux-aarch64-low.c looks
the same except for the code printing debug message. In GDB, we use
fprintf_unfiltered (gdb_stdlog, ...) while in GDBserver, we use
fprintf (stderr, ...). This patch is to change them to use debug_printf
so that these functions are the same, and I can move them to a common
place in the following patch.
gdb:
2015-07-17 Yao Qi <yao.qi@linaro.org>
* aarch64-linux-nat.c (aarch64_show_debug_reg_state): Use
debug_printf.
(aarch64_handle_unaligned_watchpoint): Likewise.
gdb/gdbserver:
2015-07-17 Yao Qi <yao.qi@linaro.org>
* linux-aarch64-low.c (aarch64_show_debug_reg_state): Use
debug_printf.
(aarch64_handle_unaligned_watchpoint): Likewise.
This patch is to use 'enum target_hw_bp_type' instead of int for
breakpoint type, in order to make some functions in GDB and
GDBserver looks similar.
gdb:
2015-07-17 Yao Qi <yao.qi@linaro.org>
* aarch64-linux-nat.c (aarch64_dr_state_insert_one_point): Change
argument type's type to 'enum target_hw_bp_type'.
(aarch64_dr_state_remove_one_point): Likewise.
(aarch64_handle_breakpoint): Likewise.
(aarch64_linux_insert_hw_breakpoint): Likewise.
(aarch64_linux_remove_hw_breakpoint): Likewise.
(aarch64_handle_aligned_watchpoint): Likewise.
aarch64_linux_get_debug_reg_capacity is called by
aarch64_linux_child_post_startup_inferior, and argument ptid is created in
inf-ptrace.c:inf_ptrace_create_inferior,
/* On some targets, there must be some explicit actions taken after
the inferior has been started up. */
target_post_startup_inferior (pid_to_ptid (pid));
so in aarch64_linux_get_debug_reg_capacity, we can get pid by ptid_get_pid,
and don't need to use get_thread_id.
gdb:
2015-07-17 Yao Qi <yao.qi@linaro.org>
* aarch64-linux-nat.c (aarch64_linux_get_debug_reg_capacity): Call
ptid_get_pid instead of get_thread_id.
We did a code refacotr here
https://sourceware.org/ml/gdb-patches/2013-11/msg00063.html
> (get_current_thread): New function, factored out from ...
> (add_current_inferior_and_thread): ... this. Adjust.
>
>@@ -3332,18 +3371,8 @@ add_current_inferior_and_thread (char *wait_status)
>
> inferior_ptid = null_ptid;
>
>- /* Now, if we have thread information, update inferior_ptid. First
>- if we have a stop reply handy, maybe it's a T stop reply with a
>- "thread" register we can extract the current thread from. If
>- not, ask the remote which is the current thread, with qC. The
>- former method avoids a roundtrip. Note we don't use
>- remote_parse_stop_reply as that makes use of the target
>- architecture, which we haven't yet fully determined at this
>- point. */
>- if (wait_status != NULL)
>- ptid = stop_reply_extract_thread (wait_status);
>- if (ptid_equal (ptid, null_ptid))
>- ptid = remote_current_thread (inferior_ptid);
>+ /* Now, if we have thread information, update inferior_ptid. */
>+ ptid = get_current_thread (wait_status);
but after the refactor, local variable ptid is used without
initialisation. However, before this change, ptid is initialised to
null_ptid. This error can be found by valgrind too...
==3298== at 0x6B99BA: ptid_equal (ptid.c:80)
==3298== by 0x4C67FF: get_current_thread (remote.c:3484)
==3298== by 0x4C6951: add_current_inferior_and_thread (remote.c:3511)
==3298== by 0x4C762C: extended_remote_create_inferior (remote.c:8506)
==3298== by 0x5A5312: run_command_1 (infcmd.c:606)
==3298== by 0x68B4FB: execute_command (top.c:463)
==3298== by 0x5C7214: command_handler (event-top.c:494)
==3298== by 0x5C78A3: command_line_handler (event-top.c:692)
==3298== by 0x6DEB57: rl_callback_read_char (callback.c:220)
==3298== by 0x5C7278: rl_callback_read_char_wrapper (event-top.c:171)
==3298== by 0x5C72C2: stdin_event_handler (event-top.c:432)
==3298== by 0x5C6194: gdb_wait_for_event (event-loop.c:834)
This patch initialises local variable ptid to null in get_current_thread.
We don't need to initialise ptid in add_current_inferior_and_thread,
so this patch also removes the ptid initialisation.
gdb:
2015-07-17 Yao Qi <yao.qi@linaro.org>
* remote.c (get_current_thread): Initialise ptid to null_ptid.
(add_current_inferior_and_thread): Don't initialise ptid.
This new test fails on i686 buildbot slaves,
(gdb) core-file /home/gdb-buildbot-2/fedora-x86-64-2/fedora-i686/build/gdb/testsuite/gdb.arch/i386-biarch-core.core
"/home/gdb-buildbot-2/fedora-x86-64-2/fedora-i686/build/gdb/testsuite/gdb.arch/i386-biarch-core.core"
is not a core dump: File format not recognized
(gdb) FAIL: gdb.arch/i386-biarch-core.exp: core-file
There are two problems:
(1) The testcase did not really test if elf64-i386 is supported by GDB (BFD).
That was OK for a Fedora testcase but I forgot about it when submitting it
upstream.
I haven't really verified if the GNU target is elf64-little but it seems so,
no other one seems suitable from:
elf32-x86-64
elf64-big
elf64-k1om
elf64-l1om
elf64-little
elf64-x86-64
pei-x86-64
(2) The output of the "core-file" command itself can be arbitrary as the
elf64-i386 file with x86_64 registers is really broken; but that does not
matter much, important is the following test whether core file memory is
readable.
./configure --enable-64-bit-bfd
(gdb) core-file /home/jkratoch/redhat/gdb-test-build32-plus64/gdb/testsuite/gdb.arch/i386-biarch-core.core^M
warning: Couldn't find general-purpose registers in core file.^M
Failed to read a valid object file image from memory.^M
warning: Couldn't find general-purpose registers in core file.^M
#0 <unavailable> in ?? ()^M
(gdb) FAIL: gdb.arch/i386-biarch-core.exp: core-file
x/i 0x400078^M
0x400078: hlt ^M
(gdb) PASS: gdb.arch/i386-biarch-core.exp: .text is readable
I do not know much dejagnu but I expect 'istarget' tests against the site.exp
'target_triplet' content which is set to the primary GDB target
(--target=...).
GDB is normally never configured for primary target elf64-i386, I think BFD
does not know such explicit target, it gets recognized as elf64-little.
In fact many testfiles of the GDB testsuite are wrong as they require
'istarget' (therefore primary GDB target) even for just loading arch specific
files which would be sufficient with secondary target (--enable-targets=...)
support.
This my new patch removes this 'istarget' check as it is IMO unrelated to what
we need to test. Although you are right we do 'x/i' and test for 'hlt' so
I think we should test also for available 'set architecture i386'.
We could also test by 'x/bx' instead of 'x/i' to avoid such additional
test/requirement.
This testcase comes from a different bug from 2009:
https://bugzilla.redhat.com/show_bug.cgi?id=457187http://pkgs.fedoraproject.org/cgit/gdb.git/commit/?id=94cd124608bf0dd359cb48a710800d72c21b30c3
That bug has been fixed in the meantime but the same testcase was reproducing
this new different bug - internal error regression - so I submitted it.
We can remove the "x/bx $address" test but it was useful for the previous bug
from 2009 as that time the internal error regression did not happen, just the
core file was not recognized (which would not be detected by the proposed
ignoring of the "core-file" command output) and so the core file was not
available. That can be tested by the "x/bx $address" test.
gdb/testsuite/ChangeLog
2015-07-16 Jan Kratochvil <jan.kratochvil@redhat.com>
* gdb.arch/i386-biarch-core.exp: Replace istarget
by "complete set gnutarget". Remove expectation for the "core-file"
command.
I noticed two failure in gdb.trace/mi-trace-frame-collected.exp:
FAIL: gdb.trace/mi-trace-frame-collected.exp: live:
-trace-frame-collected (register)
FAIL: gdb.trace/mi-trace-frame-collected.exp: tfile:
-trace-frame-collected (register)
In these cases, we are not collecting registers so the MI command
-trace-frame-collected should only give us the value of the PC.
However, it also gives us all of the single precision pseudo registers,
initialized with 0x0.
We can reproduce this error by simply issuing the
'maint print cooked-register' when no inferior is connected:
~~~
...
(gdb) maint print cooked-register
Name Nr Rel Offset Size Type Cooked value
x0 0 0 0 8 long <unavailable>
x1 1 1 8 8 long <unavailable>
...
d30 130 62 1540 8 *1 <unavailable>
d31 131 63 1548 8 *1 <unavailable>
s0 132 64 1556 4 *1 0x00000000
s1 133 65 1560 4 *1 0x00000000
s2 134 66 1564 4 *1 0x00000000
...
s28 160 92 1668 4 *1 0x00000000
s29 161 93 1672 4 *1 0x00000000
s30 162 94 1676 4 *1 0x00000000
s31 163 95 1680 4 *1 0x00000000
h0 164 96 1684 2 *1 <unavailable>
h1 165 97 1686 2 *1 <unavailable>
h2 166 98 1688 2 *1 <unavailable>
...
~~~
It turns out GDB does not check if S registers are valid before returning
a value for them. It should return <unavailable> in this case.
gdb/ChangeLog:
* aarch64-tdep.c (aarch64_pseudo_read_value): Mark S register as
unavailable if invalid.
New testcase.
gdb/testsuite/ChangeLog
2015-07-15 Aleksandar Ristovski <aristovski@qnx.com
Tests for validate symbol file using build-id.
* gdb.base/solib-mismatch-lib.c: New file.
* gdb.base/solib-mismatch-libmod.c: New file.
* gdb.base/solib-mismatch.c: New file.
* gdb.base/solib-mismatch.exp: New file.
Producer part of the new "build-id" XML attribute.
gdb/ChangeLog
2015-07-15 Aleksandar Ristovski <aristovski@qnx.com
Jan Kratochvil <jan.kratochvil@redhat.com>
gdbserver build-id attribute generator.
* features/library-list-svr4.dtd (library-list-svr4): New
'build-id' attribute.
gdb/doc/ChangeLog
2015-07-15 Aleksandar Ristovski <aristovski@qnx.com
Jan Kratochvil <jan.kratochvil@redhat.com>
gdbserver build-id attribute generator.
* gdb.texinfo (Library List Format for SVR4 Targets): Add
'build-id' in description, example, new attribute in dtd.
gdb/gdbserver/ChangeLog
2015-07-15 Aleksandar Ristovski <aristovski@qnx.com
Jan Kratochvil <jan.kratochvil@redhat.com>
gdbserver build-id attribute generator.
* linux-low.c (nat/linux-maps.h, search.h, rsp-low.h): Include.
(ElfXX_Ehdr, ElfXX_Phdr, ElfXX_Nhdr): New.
(ELFXX_FLD, ELFXX_SIZEOF, ELFXX_ROUNDUP, BUILD_ID_INVALID): New.
(find_phdr): New.
(get_dynamic): Use find_pdhr to traverse program headers.
(struct mapping_entry, mapping_entry_s, free_mapping_entry_vec)
(compare_mapping_entry_range, struct find_memory_region_callback_data)
(read_build_id, find_memory_region_callback, lrfind_mapping_entry)
(get_hex_build_id): New.
(linux_qxfer_libraries_svr4): Add optional build-id attribute
to reply XML document.
This should be just a move with no changes.
gdb/ChangeLog
2015-07-15 Aleksandar Ristovski <aristovski@qnx.com
Jan Kratochvil <jan.kratochvil@redhat.com>
Move linux_find_memory_regions_full & co.
* linux-tdep.c (nat/linux-maps.h): Include.
(gdb_regex.h): Remove the include.
(enum filterflags, struct smaps_vmflags, read_mapping, decode_vmflags)
(mapping_is_anonymous_p, dump_mapping_p): Moved to nat/linux-maps.c.
(linux_find_memory_region_ftype): Moved typedef to nat/linux-maps.h.
(linux_find_memory_regions_full): Moved definition to nat/linux-maps.c.
* nat/linux-maps.c: Include ctype.h, target/target-utils.h, gdb_regex.h
and target/target.h.
(struct smaps_vmflags, read_mapping, decode_vmflags)
(mapping_is_anonymous_p, dump_mapping_p): Move from linux-tdep.c.
(linux_find_memory_regions_full): Move from linux-tdep.c.
* nat/linux-maps.h (read_mapping): New declaration.
(linux_find_memory_region_ftype, enum filterflags): Moved from
linux-tdep.c.
(linux_find_memory_regions_full): New declaration.
* target.c (target/target-utils.h): Include.
(read_alloc_pread_ftype): Moved typedef to target/target-utils.h.
(read_alloc, read_stralloc_func_ftype, read_stralloc): Moved
definitions to target/target-utils.c.
* target.h (target_fileio_read_stralloc): Move it to target/target.h.
* target/target-utils.c (read_alloc, read_stralloc): Move definitions
from target.c.
* target/target-utils.h (read_alloc_pread_ftype): New typedef.
(read_alloc): New declaration.
(read_stralloc_func_ftype): New typedef.
(read_stralloc): New declaration.
* target/target.h (target_fileio_read_stralloc): Move it from target.h.
gdb/gdbserver/ChangeLog
2015-07-15 Aleksandar Ristovski <aristovski@qnx.com
Jan Kratochvil <jan.kratochvil@redhat.com>
* target.c: Include target/target-utils.h and fcntl.h.
(target_fileio_read_stralloc_1_pread, target_fileio_read_stralloc_1)
(target_fileio_read_stralloc): New functions.
Prepare code for move into gdb/common/.
gdb/ChangeLog
2015-07-15 Aleksandar Ristovski <aristovski@qnx.com
Jan Kratochvil <jan.kratochvil@redhat.com>
Prepare linux_find_memory_regions_full & co. for move.
* linux-tdep.c (linux_find_memory_region_ftype): Comment.
(linux_find_memory_regions_full): Change signature and prepare
for moving to linux-maps.
(linux_find_memory_regions_data): Rename field 'obfd' to 'data'.
(linux_find_memory_regions_thunk): New.
(linux_find_memory_regions_thunk): Use 'data' field instead of 'obfd'.
(linux_find_memory_regions_gdb): New.
(linux_find_memory_regions): Rename argument 'obfd' to 'func_data'.
(linux_make_mappings_corefile_notes): Use
linux_find_memory_regions_gdb.
* target.c (read_alloc_pread_ftype): New typedef.
(target_fileio_read_alloc_1_pread): New function.
(read_alloc): Refactor from target_fileio_read_alloc_1.
(read_stralloc_func_ftype): New typedef.
(target_fileio_read_alloc_1): New implementation. Use read_alloc.
(read_stralloc): Refactored from target_fileio_read_stralloc.
(target_fileio_read_stralloc): New implementation, use read_stralloc.
Later patches need regex support also in gdbserver.
gdb/ChangeLog
2015-07-15 Jan Kratochvil <jan.kratochvil@redhat.com>
* Makefile.in (HFILES_NO_SRCDIR): Change gdb_regex.h to
common/gdb_regex.h.
(COMMON_OBS): Add gdb_regex.o.
(gdb_regex.o): New.
* common/common.m4 (GDB_AC_COMMON): Add gdb_use_included_regex,
--without-included-regex and USE_INCLUDED_REGEX.
* common/gdb_regex.c: New file from utils.c functions.
* common/gdb_regex.h: Move it here from gdb_regex.h, update include
file wrapping define name.
* configure: Rebuilt.
* configure.ac (gdb_use_included_regex, --without-included-regex)
(USE_INCLUDED_REGEX): Move them to common/common.m4.
* gdb_regex.h: Move it to common/gdb_regex.h.
* utils.c: Remove include gdb_regex.h.
(do_regfree_cleanup, make_regfree_cleanup, get_regcomp_error)
(compile_rx_or_error): Move them to common/gdb_regex.c.
gdb/gdbserver/ChangeLog
2015-07-15 Jan Kratochvil <jan.kratochvil@redhat.com>
* Makefile.in (OBS): Add gdb_regex.o.
(gdb_regex.o): New.
* config.in: Rebuilt.
* configure: Rebuilt.
Tracepoints and range stepping are independent features. This patch
skips the gdb.trace/range-stepping.exp test case if the target does not
support range stepping.
gdb/testsuite/ChangeLog:
* gdb.base/range-stepping.exp (gdb_range_stepping_enabled):
Move it to ...
* lib/range-stepping-support.exp (gdb_range_stepping_enabled):
... here.
* gdb.trace/range-stepping.exp: Check that the target supports
range stepping.
Fix the ARI warning about the use of unsigned long long. We can't use
ULONGEST as this is defined unsigned long on 64-bit systems. This will
result in a compile error when storing a pointer to an unsigned long long
structure field (declared in perf_event.h as __u64) in a ULONGEST * variable.
Use size_t to hold the buffer size inside GDB and __u64 when interfacing the
Linux kernel.
gdb/
* nat/linux-btrace.c (perf_event_read): Change the type of DATA_HEAD.
(perf_event_read_all): Change the type of SIZE and DATA_HEAD.
(perf_event_read_bts): Change the type of SIZE and READ.
(linux_enable_bts): Change the type of SIZE, PAGES, DATA_SIZE,
and DATA_OFFSET. Move DATA_SIZE declaration. Restrict the buffer size
to UINT_MAX. Check for overflows when using DATA_HEAD from the perf
mmap page.
(linux_enable_pt): Change the type of PAGES and SIZE. Restrict the
buffer size to UINT_MAX.
(linux_read_bts): Change the type of BUFFER_SIZE, SIZE, DATA_HEAD, and
DATA_TAIL.
* nat/linux-btrace.h (struct perf_event_buffer)<size, data_head>
<last_head>: Change type.
* common/btrace-common.h (struct btrace_dat_pt) <size>: Change type.
* common/btrace-common.c (btrace_data_append): Change the type of
SIZE.
* btrace.c (parse_xml_raw): Change the type of SIZE. Change oddness
check.
Extends existing support for namespaces/modules in C++/Fortran/Java to
include language_d too. However unlike Fortran/C++, the separator for
qualified names is a single dot.
2015-07-14 Iain Buclaw <ibuclaw@gdcproject.org>
* dwarf2read.c (find_slot_in_mapped_hash): Extend language support to
also test for language_d.
(dwarf2_compute_name): Likewise.
(read_func_scope): Likewise.
(read_structure_type): Likewise.
(determine_prefix): Likewise.
(read_import_statement): Use dot as the separator for language_d.
(typename_concat): Likewise, but don't prefix the D main function.
* nat/linux-namespaces.c (setns): Rename from this ...
(do_setns): ... to this. Support calling setns if it exists.
(mnsh_handle_setns): Call do_setns.
This exercises the case of the inferior disappearing while GDB is
debugging it, such as something doing "kill -9 PID" while the program
is stopped under GDB or GDBserver. This triggered a set of internal
errors, fixed by previous patches.
gdb/testsuite/ChangeLog:
2015-07-14 Pedro Alves <palves@redhat.com>
* gdb.base/killed-outside.exp: New file.
* gdb.base/killed-outside.c: New file.
If the process disappears (e.g., killed with "kill -9" from the shell)
while it was stopped under GDBserver's control, and the GDBserver
tries to kill it, GDBserver asserts:
(gdb) shell kill -9 23084
(gdb) kill
...
Killing process(es): 23084
/home/pedro/gdb/mygit/src/gdb/gdbserver/linux-low.c:972: A problem internal to GDBserver has been detected.
kill_wait_lwp: Assertion `res > 0' failed.
...
gdb/gdbserver/ChangeLog:
2015-07-14 Pedro Alves <palves@redhat.com>
* linux-low.c (kill_wait_lwp): Don't assert if waitpid fails.
Instead, ignore ECHILD, and throw an error for other errnos.
When I examine the buildbot fails, I see this fail on
native-extended-gdbserver,
Attaching to process 13529^M
"target:/scratch/yao/gdb/build-git/x86_64/gdb/testsuite/gdb.base/attach-pie-noexec (deleted)": could not open as an executable file: No such file or directory^M
(gdb) FAIL: gdb.base/attach-pie-noexec.exp: attach
if I run tests with board file unix, it doesn't exist,
Attaching to process 13869^M
/scratch/yao/gdb/build-git/x86_64/gdb/testsuite/gdb.base/attach-pie-noexec (deleted): No such file or directory.^M
(gdb) PASS: gdb.base/attach-pie-noexec.exp: attach
the test expects to see the period at the end of the error message,
gdb_test "attach $testpid" "Attaching to process $testpid\r\n.*: No such file or directory\\." "attach"
however the period is missing when running with native-extended-gdbserver.
in exec.c:exec_file_attach, GDB has two places may throw errors [1] and [2],
if (load_via_target)
{
...
}
else
{
...
if (scratch_chan < 0)
perror_with_name (filename); <--- [1]
}
...
if (!exec_bfd)
{
error (_("\"%s\": could not open as an executable file: %s"), <-- [2]
scratch_pathname, bfd_errmsg (bfd_get_error ()));
}
perror_with_name [1] append a period at the end of error message,
but error [2] doesn't. This fix is to add a period at the end of the
error message. Note that this fail is shown up on 7.9 release as well.
gdb:
2015-07-13 Yao Qi <yao.qi@linaro.org>
* exec.c (exec_file_attach): Add period at the end of error
message.
Share the window name completion code from the focus command with the
winheight command, providing window name completion for the winheight
command.
gdb/ChangeLog:
* tui/tui-win.c (window_name_completer): New function.
(focus_completer): Call window_name_completer. All old content
moved into window_name_completer.
(winheight_completer): New function.
(_initialize_tui_win): Rename variable. Add completer to
winheight command. Update doc string on winheight.
This change causes the prologue scanner and the frame type scanner in
rx-tdep.c to use target_read_code() instead of target_read_memory().
This change allows these instruction scanners to operate much more
quickly due to the fact that target_read_code() can potentially read
from a cache maintained by GDB.
gdb/ChangeLog:
* rx-tdep.c (rx_get_opcode_byte): Use target_read_code instead
of target_read_memory.
Building with C++ catches a buglet here:
../../../src/gdb/gdbserver/event-loop.c:205:19: warning: invalid conversion from ‘gdb_client_data {aka void*}’ to ‘void**’ [-fpermissive]
event_ptr->data = data;
^
This works in practice because gdb_client_data is a pointer already
(hence in C we get an implicit conversion), and nothing deferences the
pointer. It's passed from client at event registration/creation time,
only to pass straight back to client callback.
Well, that and nothing in gdbserver uses the event data anyway.
gdb/gdbserver/ChangeLog:
2015-07-10 Pedro Alves <palves@redhat.com>
* event-loop.c (struct callback_event) <data>: Change type to
gdb_client_data instance instead of gdb_client_data pointer.
(append_callback_event): Adjust.
I have somehow missed gdb.asm/asm-source.exp PASS->FAIL even on x86_64.
It has no longer valid assumption that "break" breaks after the prologue even
in assembler. So I have changed this assumption of the testfile.
gdb/testsuite/ChangeLog
2015-07-10 Jan Kratochvil <jan.kratochvil@redhat.com>
* gdb.asm/asm-source.exp (f at main): Stop at gdbasm_enter.
(n at main): New.
* gdb.asm/asmsrc1.s: Add comment "mark: main enter".
This patch cleans up the comments for each linux_target_ops methods. We
should mention which method each function implements but there is no
need to duplicate information already mentionned in the base target_ops
or linux_target_ops definitions.
gdb/gdbserver/ChangeLog:
* linux-aarch64-low.c: Add comments for each linux_target_ops
method. Remove comments already covered in target_ops and
linux_target_ops definitions.
(the_low_target): Add comments for each unimplemented method.
In parse_scrolling_args it is possible for a string copy to leak if an
error occurs. Switching to using a cleanup fixes this leak.
In tui_set_win_height the string can't be leaked, but switching to using
a cleanup guards against the possibility that a leak could be introduced
in the future (by adding an error somewhere in the call stack).
gdb/ChangeLog:
* tui/tui-win.c (tui_set_win_height): Use a cleanup to free the
string copy.
(parse_scrolling_args): Likewise.
Don't duplicate the window names inside the completion function.
Instead make use of the existing defines, and the tui_win_name function
to obtain the window names.
gdb/ChangeLog:
* tui/tui-win.c (focus_completer): Don't duplicate the tui window
names in this function.
This commit converts the window names for the TUI windows to lower case.
The windows names are already lower case in the documentation, and are
shown as lower case in some of the command completion results.
Given that all the commands that take a window name currently accept
upper or lower case, this commit just changes the window names to lower
case in the remaining places they are displayed by gdb.
gdb/ChangeLog:
* tui/tui-data.h (SRC_NAME): Convert to lower case.
(CMD_NAME): Likewise.
(DATA_NAME): Likewise.
(DISASSEM_NAME): Likewise.
* tui/tui-win.c (tui_set_focus): Window names are now lower case.
(tui_set_win_height): Likewise.
(parse_scrolling_args): Likewise.
Since the new KFAILs/KPASSs for the infcall tests on x86 and x86_64
targets generated unnecessary noise, this change skips them with
UNSUPPORTED instead.
gdb/testsuite/ChangeLog:
* gdb.base/gnu_vector.exp: On x86 and x86_64 targets, skip the
infcall tests instead of setting up for KFAIL.
When navigating in the recorded execution trace via "record goto", we do not
set stop_pc. This may trigger an internal error in infrun.c when stepping
from that location. Set it.
(gdb) rec full
(gdb) c
Continuing.
Breakpoint 1, foo (void) at foo.c:42
42 x = y
(gdb) rn
foo (void)
at foo.c:41
41 y = x
(gdb) rec go end
Go forward to insn number 98724
at foo.c:42
42 x = y
(gdb) n
infrun.c:2382: internal-error: resume: Assertion `sig != GDB_SIGNAL_0' failed.
A problem internal to GDB has been detected,
further debugging may prove unreliable.
Quit this debugging session? (y or n)
This happens because there's a breakpoint at PC when the "next"
is issued, so that breapoint should be immediately stepped over.
That should have been detected/done by proceed, here:
if (addr == (CORE_ADDR) -1)
{
if (pc == stop_pc
&& breakpoint_here_p (aspace, pc) == ordinary_breakpoint_here
&& execution_direction != EXEC_REVERSE)
/* There is a breakpoint at the address we will resume at,
step one instruction before inserting breakpoints so that
we do not stop right away (and report a second hit at this
breakpoint).
Note, we don't do this in reverse, because we won't
actually be executing the breakpoint insn anyway.
We'll be (un-)executing the previous instruction. */
tp->stepping_over_breakpoint = 1;
But since stop_pc was stale, the pc == stop_pc check failed, and left the
breakpont at PC inserted.
gdb/
* record-btrace.c (record_btrace_goto_begin, record_btrace_goto_end)
record_btrace_goto): Move call to print_stack_frame ...
(record_btrace_set_replay): ... here. Set stop_pc.
* record-full.c (record_full_goto_entry): Set stop_pc.
testsuite/
* gdb.btrace/record_goto-step.exp: New.
This patch adds support for AArch64 to the gdb.trace testsuite.
Note that it does not add support for testing fast tracepoint as it
isn't supported. Therefore the test cases with inline assembly are not
ported in this patch, as we do not know what the conditions for
inserting a fast tracepoint on AArch64 would be.
gdb/testsuite/ChangeLog:
* gdb.trace/backtrace.exp: Set registers for aarch64 target.
* gdb.trace/collection.exp: Likewise.
* gdb.trace/mi-trace-frame-collected.exp: Likewise.
* gdb.trace/mi-trace-unavailable.exp: Likewise.
* gdb.trace/report.exp: Likewise.
* gdb.trace/trace-break.exp: Likewise.
* gdb.trace/unavailable.exp: Likewise.
* gdb.trace/while-dyn.exp: Likewise.
This patch implements the 'collect $_ret' command to collect the return
address of a function in a tracepoint. It marks the LR register for
collection.
gdb/ChangeLog:
* aarch64-tdep.c: Add ax.h and ax-gdb.h includes.
(aarch64_gen_return_address): New function.
(aarch64_gdbarch_init): Hook it.
The stub unwinder is used on AArch64 if the target's memory is not
readable at the current PC. For example, the user could try to call at
an invalid address such as 0x0, as covered in the gdb.base/signull.exp
test case. Many GDB ports use a similar unwinder to handle this case
too.
If we purposely kill the inferior before examining the trace then we get
the following issue:
~~~
...
(gdb) trace f
Tracepoint 3 at 0x7fb7fc28c0
(gdb) tstart
(gdb) continue
...
(gdb) tstop
(gdb) tsave /tmp/trace
(gdb) kill
...
(gdb) target tfile /tmp/trace
...
(gdb) tfind
Register 31 is not available.
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Found trace frame 0, tracepoint 3
#-1 0x0000007fb7fc28c0 in f () ...
^^^
~~~
This patch teaches the stub unwinder to report to the core frame code
with UNWIND_UNAVAILABLE when either the stack pointer of the return
address are unavailable to read from the target.
gdb/ChangeLog:
* aarch64-tdep.c (aarch64_make_stub_cache): Set available_p and
swallow NOT_AVAILABLE_ERROR.
(aarch64_stub_this_id): Call frame_id_build_unavailable_stack if
available_p is not set.
(aarch64_stub_frame_unwind_stop_reason): New function.
(aarch64_stub_unwind): Install it.
Without debugging information, we have the following issue when
examining a trace buffer:
~~~
...
(gdb) trace f
Tracepoint 3 at 0x7fb7fc28c0
(gdb) tstart
(gdb) continue
...
(gdb) tstop
(gdb) tfind start
Register 31 is not available.
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Found trace frame 0, tracepoint 3
#-1 0x0000007fb7fc28c0 in f () ...
^^^
~~~
The reason for this is that the target's stack pointer is unavailable
when examining the trace buffer. What we are seeing is due to the
'tfind' command creating a sentinel frame and unwinding it. If an
exception is thrown, we are left with the sentinel frame being displayed
at level #-1. The exception is thrown when the prologue unwinder tries
to read the stack pointer to construct an ID for the frame.
This patch fixes this by making the prologue unwinder catch
NOT_AVAILABLE_ERROR exceptions when either registers or memory is
unreadable and report back to the frame core code with
UNWIND_UNAVAILABLE.
gdb/ChangeLog:
* aarch64-tdep.c (aarch64_prologue_cache) <available_p>: New
field.
(aarch64_make_prologue_cache_1): New function, factored out from
aarch64_make_prologue_cache. Do not allocate cache. Set
available_p.
(aarch64_make_prologue_cache): Reimplement wrapping
aarch64_make_prologue_cache_1, and swallowing
NOT_AVAILABLE_ERROR.
(aarch64_prologue_frame_unwind_stop_reason): New function.
Return UNWIND_UNAVAILABLE if available_p is not set.
(aarch64_prologue_unwind): Install it.
(aarch64_prologue_this_id): Move prev_pc and prev_sp limit
checks into aarch64_prologue_frame_unwind_stop_reason. Call
frame_id_build_unavailable_stack if available_p is not set.
