to increase it broke the ability to write large chunks of memory
with m68k-stub and i386-stub. Now we only use more than 400 on
machines where we need that much to write the registers.
* remote.c (remote_write_bytes): Eliminate possible abort(). The
check for when to abort was off by a few bytes and besides which,
it is handled by MAXBUFBYTES, which the caller uses.
* m68k-stub.c: Add comments about trap #1 and trap #8 instructions.
* breakpoint.c: Include thread.h.
* coffread.c: Include stabsread.h.
* Makefile.in: Update dependencies.
* breakpoint.c (mention): Add bp_call_dummy to switch.
* symmisc.c (dump_symtab): Use %d not %ld for line number.
just started failing because they depended on the order the
subcommands are presented, or exact docstring text. This kind of
test is a pain and has minimal benefit.
initialized and uninitialized data sections have the SEC_ALLOC
flag bit set, but only initialized sections have SEC_LOAD set.
SEC_DATA is ignored since it only gets set for initialized
data. Likewise, SEC_HAS_CONTENTS is ignored now because it
never gets set.
* dst.h, dstread.c, config/m68k/{apollo68b.mt,tm-apollo68b.h}:
New files.
* config/m68k/nm-apollo68b.h: Add more defines.
* configure.in: Recognize apollo target, not just host.
* dst.h, dstread.c, config/m68k/{apollo68b.mt,tm-apollo68b.h}:
New files.
* config/m68k/nm-apollo68b.h: Add more defines.
* configure.in: Recognize apollo target, not just host.
cleans up all kinds of hassles (which nm to use in munch, etc). The
new formatting conventions (mostly already followed) are that
the name of the _initialize_* routines must start in column zero,
and must not be inside #if.
* munch: Removed.
* Makefile.in: Remove references to munch.
* serial.c, remote.c, infptrace.c, maint.c, convex-tdep.c,
alpha-tdep.c, hp300ux-nat.c, hppab-nat.c, osfsolib.c, remote-es.c,
procfs.c, remote-udi.c, ser-go32.c, ultra3-xdep.c, sh-tdep.c,
i960-tdep.c, hppa-tdep.c, h8500-tdep.c, dpx2-nat.c, delta68-nat.c,
z8k-tdep.c: Make sure the above conventions are followed. Make
sure they are all declared as returning void. Clean up
miscellaneous comments and such.
cleans up all kinds of hassles (which nm to use in munch, etc). The
new formatting conventions (mostly already followed) are that
the name of the _initialize_* routines must start in column zero,
and must not be inside #if.
* munch: Removed.
* Makefile.in: Remove references to munch.
* serial.c, remote.c, infptrace.c, maint.c, convex-tdep.c,
alpha-tdep.c, hp300ux-nat.c, hppab-nat.c, osfsolib.c, remote-es.c,
procfs.c, remote-udi.c, ser-go32.c, ultra3-xdep.c, sh-tdep.c,
i960-tdep.c, hppa-tdep.c, h8500-tdep.c, dpx2-nat.c, delta68-nat.c,
z8k-tdep.c: Make sure the above conventions are followed. Make
sure they are all declared as returning void. Clean up
miscellaneous comments and such.
* remote.c, remote-udi.c, remote-utils.h: Let target.h take care of
declaring these. Those random externs all over are error prone.
* Move "set remotebaud" from remote-utils.c to main.c to it applies
to remote.c as well.
* xcoffread.c (xcoff_symfile_read), coffread.c (coff_symfile_read):
Sort symtabs for this objfile only, not for all objfiles.
* symfile.c, symfile.h (sort_all_symtab_syms): Remove; no longer used.
remove #include "remote-utils.h". This makes it possible to build
GDB without remote-utils.c. Also, move setting of remote_debug
into main, so that all remote*.c files can use it (not just the
serial line ones). And, make baud_rate be an int.
* remote-udi.c: Change kiodebug to remote_debug.
* remote-utils.c: Move setting of baud rate and debug into main.c.
* remote-utils.h: Redefine sr_{get set}_debug and sr_{get set}_baud
to use baud_rate and remote_debug globals for compatibility.
* remote.c: Use remote_debug and baud_rate globals directly,
instead of sr_ functions, so that we don't need to load
remote-utils.c.
