right operations ourself, rather than calling symbol_file_command.
If we re-read something, call clear_symtab_users not just
breakpoint_re_set.
* objfiles.h, objfiles.c (build_objfile_section_table): No longer
static.
* symfile.c (clear_symtab_users): Call clear_pc_function_cache.
* coffread.c, dbxread.c, elfread.c, mipsread.c, nlmread.c, paread.c
(*_symfile_offsets): Set objfile->num_sections.
* remote.c (remote_wait), symfile.c (syms_from_objfile):
Don't muck with objfile->num_sections now that all the symbol
readers set it.
* elfread.c: Clean up obsolete comment about handling only DWARF.
* paread.c: Remove comment about how we should use an "ordinary"
file format with an hppa suffix. There is nothing ordinary about SOM.
* Move SWAP_TARGET_AND_HOST from defs.h to findvar.c because it is
now used only by extract_floating and store_floating.
* valprint.c (print_floating): Use unsigned arithmetic. Use
extract_unsigned_integer instead of SWAP_TARGET_AND_HOST.
Change sizeof (float) to 4 and sizeof (double) to 8 (those are always
the relevant sizes for this code, which is in #ifdef IEEE_FLOAT).
* values.c (unpack_long, unpack_double, value_from_double),
valarith.c (value_binop), stabsread.c (define_symbol):
Use extract_floating and store_floating instead of
SWAP_TARGET_AND_HOST.
* config/m68k/tm-m68k.h, config/i960/tm-i960.h (REGISTER_CONVERT_*):
Use extract_floating and store_floating.
* config/m88k/tm-m88k.h: Add comments (it should be doing the same).
* i386-tdep.c (i386_extract_return_value),
* remote-nindy.c (nindy_store_registers): Use store_floating.
Remove John's name and email address. Remove item on "always"
("hook-stop" takes care of this). Remove item on executables with
no symbols (this works on some machines, at least). Remove item
about calling error() during symbol reading (I think all the important
ones have been cleaned up). Revise items about signals and remote
systems. Remove section on ^Z requiring several continues to make
it go (this now works. Perhaps the item is based on confusion over
programs (like GDB itself) which catch SIGTSTP and then re-send
themselves the signal. PR 2575 might contain relevant info).
* remote-mon.c: Remove commented out "set remotedebug" command.
* remote-nindy.c: Clean up comment about wanting alternative to
options specified on the GDB command line.
to increase it broke the ability to write large chunks of memory
with m68k-stub and i386-stub. Now we only use more than 400 on
machines where we need that much to write the registers.
* remote.c (remote_write_bytes): Eliminate possible abort(). The
check for when to abort was off by a few bytes and besides which,
it is handled by MAXBUFBYTES, which the caller uses.
* m68k-stub.c: Add comments about trap #1 and trap #8 instructions.
* breakpoint.c: Include thread.h.
* coffread.c: Include stabsread.h.
* Makefile.in: Update dependencies.
* breakpoint.c (mention): Add bp_call_dummy to switch.
* symmisc.c (dump_symtab): Use %d not %ld for line number.
initialized and uninitialized data sections have the SEC_ALLOC
flag bit set, but only initialized sections have SEC_LOAD set.
SEC_DATA is ignored since it only gets set for initialized
data. Likewise, SEC_HAS_CONTENTS is ignored now because it
never gets set.
* dst.h, dstread.c, config/m68k/{apollo68b.mt,tm-apollo68b.h}:
New files.
* config/m68k/nm-apollo68b.h: Add more defines.
* configure.in: Recognize apollo target, not just host.
cleans up all kinds of hassles (which nm to use in munch, etc). The
new formatting conventions (mostly already followed) are that
the name of the _initialize_* routines must start in column zero,
and must not be inside #if.
* munch: Removed.
* Makefile.in: Remove references to munch.
* serial.c, remote.c, infptrace.c, maint.c, convex-tdep.c,
alpha-tdep.c, hp300ux-nat.c, hppab-nat.c, osfsolib.c, remote-es.c,
procfs.c, remote-udi.c, ser-go32.c, ultra3-xdep.c, sh-tdep.c,
i960-tdep.c, hppa-tdep.c, h8500-tdep.c, dpx2-nat.c, delta68-nat.c,
z8k-tdep.c: Make sure the above conventions are followed. Make
sure they are all declared as returning void. Clean up
miscellaneous comments and such.
* remote.c, remote-udi.c, remote-utils.h: Let target.h take care of
declaring these. Those random externs all over are error prone.
* Move "set remotebaud" from remote-utils.c to main.c to it applies
to remote.c as well.
* xcoffread.c (xcoff_symfile_read), coffread.c (coff_symfile_read):
Sort symtabs for this objfile only, not for all objfiles.
* symfile.c, symfile.h (sort_all_symtab_syms): Remove; no longer used.
remove #include "remote-utils.h". This makes it possible to build
GDB without remote-utils.c. Also, move setting of remote_debug
into main, so that all remote*.c files can use it (not just the
serial line ones). And, make baud_rate be an int.
* remote-udi.c: Change kiodebug to remote_debug.
* remote-utils.c: Move setting of baud rate and debug into main.c.
* remote-utils.h: Redefine sr_{get set}_debug and sr_{get set}_baud
to use baud_rate and remote_debug globals for compatibility.
* remote.c: Use remote_debug and baud_rate globals directly,
instead of sr_ functions, so that we don't need to load
remote-utils.c.
