Remove John's name and email address. Remove item on "always"
("hook-stop" takes care of this). Remove item on executables with
no symbols (this works on some machines, at least). Remove item
about calling error() during symbol reading (I think all the important
ones have been cleaned up). Revise items about signals and remote
systems. Remove section on ^Z requiring several continues to make
it go (this now works. Perhaps the item is based on confusion over
programs (like GDB itself) which catch SIGTSTP and then re-send
themselves the signal. PR 2575 might contain relevant info).
config/mips/{mipsm3.mt,mipsm3.mh},
config/ns32k/{ns32km3.mt,ns32km3.mh}: Use correct names for TM_FILE
and XM_FILE. Replace host files *mach3-xdep.o with native
files *m3-nat.o. Replace host file os-mach3.o with native
file m3-nat.o.
* remote-mon.c: Remove commented out "set remotedebug" command.
* remote-nindy.c: Clean up comment about wanting alternative to
options specified on the GDB command line.
to increase it broke the ability to write large chunks of memory
with m68k-stub and i386-stub. Now we only use more than 400 on
machines where we need that much to write the registers.
* remote.c (remote_write_bytes): Eliminate possible abort(). The
check for when to abort was off by a few bytes and besides which,
it is handled by MAXBUFBYTES, which the caller uses.
* m68k-stub.c: Add comments about trap #1 and trap #8 instructions.
* breakpoint.c: Include thread.h.
* coffread.c: Include stabsread.h.
* Makefile.in: Update dependencies.
* breakpoint.c (mention): Add bp_call_dummy to switch.
* symmisc.c (dump_symtab): Use %d not %ld for line number.
just started failing because they depended on the order the
subcommands are presented, or exact docstring text. This kind of
test is a pain and has minimal benefit.
initialized and uninitialized data sections have the SEC_ALLOC
flag bit set, but only initialized sections have SEC_LOAD set.
SEC_DATA is ignored since it only gets set for initialized
data. Likewise, SEC_HAS_CONTENTS is ignored now because it
never gets set.
* dst.h, dstread.c, config/m68k/{apollo68b.mt,tm-apollo68b.h}:
New files.
* config/m68k/nm-apollo68b.h: Add more defines.
* configure.in: Recognize apollo target, not just host.
* dst.h, dstread.c, config/m68k/{apollo68b.mt,tm-apollo68b.h}:
New files.
* config/m68k/nm-apollo68b.h: Add more defines.
* configure.in: Recognize apollo target, not just host.
cleans up all kinds of hassles (which nm to use in munch, etc). The
new formatting conventions (mostly already followed) are that
the name of the _initialize_* routines must start in column zero,
and must not be inside #if.
* munch: Removed.
* Makefile.in: Remove references to munch.
* serial.c, remote.c, infptrace.c, maint.c, convex-tdep.c,
alpha-tdep.c, hp300ux-nat.c, hppab-nat.c, osfsolib.c, remote-es.c,
procfs.c, remote-udi.c, ser-go32.c, ultra3-xdep.c, sh-tdep.c,
i960-tdep.c, hppa-tdep.c, h8500-tdep.c, dpx2-nat.c, delta68-nat.c,
z8k-tdep.c: Make sure the above conventions are followed. Make
sure they are all declared as returning void. Clean up
miscellaneous comments and such.
cleans up all kinds of hassles (which nm to use in munch, etc). The
new formatting conventions (mostly already followed) are that
the name of the _initialize_* routines must start in column zero,
and must not be inside #if.
* munch: Removed.
* Makefile.in: Remove references to munch.
* serial.c, remote.c, infptrace.c, maint.c, convex-tdep.c,
alpha-tdep.c, hp300ux-nat.c, hppab-nat.c, osfsolib.c, remote-es.c,
procfs.c, remote-udi.c, ser-go32.c, ultra3-xdep.c, sh-tdep.c,
i960-tdep.c, hppa-tdep.c, h8500-tdep.c, dpx2-nat.c, delta68-nat.c,
z8k-tdep.c: Make sure the above conventions are followed. Make
sure they are all declared as returning void. Clean up
miscellaneous comments and such.
