of SIGIO.
(input_interrupt): Don't block on read, in case we got redundant
SIGIO. Don't gripe about redundant SIGIO.
* gdbserver/low-hppabsd.c (mywait): Use waitpid(). Enable SIGIO
handler while waiting.
* gdbserver/low-linux.c (mywait): Likewise.
* gdbserver/low-nbsd.c (mywait): Likewise.
* gdbserver/low-sparc.c (mywait): Likewise.
(go32_info_dos_command): New function.
(_initialize_go32_nat): Convert all DOS-specific commands into
subcommands of "info dos". Suggested by Andrew Cagney
<ac131313@redhat.com>.
reasonable defaults for REALTIME_LO and REALTIME_HI if they're not
already defined.
* config/nm-linux.h: Include <signal.h>.
[__SIGRTMIN] (REALTIME_LO, REALTIME_HI): Define to __SIGRTMIN and
(__SIGRTMAX + 1) respectively.
longer disagree on how big pointers are.
* findvar.c (value_from_register): Remove special case code for D10V.
* printcmd.c (print_frame_args): Same.
* valops.c (value_at, value_fetch_lazy): Same.
* values.c (unpack_long): Same.
* gdbarch.sh: Changes to effect the following:
* gdbarch.h (GDB_TARGET_IS_D10V, D10V_MAKE_DADDR,
gdbarch_d10v_make_daddr_ftype, gdbarch_d10v_make_daddr,
set_gdbarch_d10v_make_daddr, D10V_MAKE_IADDR,
gdbarch_d10v_make_iaddr_ftype, gdbarch_d10v_make_iaddr,
set_gdbarch_d10v_make_iaddr, D10V_DADDR_P,
gdbarch_d10v_daddr_p_ftype, gdbarch_d10v_daddr_p,
set_gdbarch_d10v_daddr_p, D10V_IADDR_P,
gdbarch_d10v_iaddr_p_ftype, gdbarch_d10v_iaddr_p,
set_gdbarch_d10v_iaddr_p, D10V_CONVERT_DADDR_TO_RAW,
gdbarch_d10v_convert_daddr_to_raw_ftype,
gdbarch_d10v_convert_daddr_to_raw,
set_gdbarch_d10v_convert_daddr_to_raw, D10V_CONVERT_IADDR_TO_RAW,
gdbarch_d10v_convert_iaddr_to_raw_ftype,
gdbarch_d10v_convert_iaddr_to_raw,
set_gdbarch_d10v_convert_iaddr_to_raw): Delete declarations.
* gdbarch.c: Delete the corresponding definitions.
(struct gdbarch): Delete members d10v_make_daddr,
d10v_make_iaddr, d10v_daddr_p, d10v_iaddr_p,
d10v_convert_daddr_to_raw, and d10v_convert_iaddr_to_raw.
(startup_gdbarch): Remove initializers for the above.
(verify_gdbarch, gdbarch_dump): Don't verify or dump them any
more.
* d10v-tdep.c (d10v_register_virtual_type): Rather that
claiming the stack pointer and PC are 32 bits long (which they
aren't), say that the stack pointer is an int16_t, and the
program counter is a function pointer. This allows the rest
of GDB to make the appropriate conversions between the code
pointer format and real addresses.
(d10v_register_convertible, d10v_register_convert_to_virtual,
d10v_register_convert_to_raw): Delete function; no registers
are convertible now, so we use
generic_register_convertible_not instead.
(d10v_address_to_pointer, d10v_pointer_to_address): New gdbarch
methods.
(d10v_push_arguments, d10v_extract_return_value): Remove special
cases for code and data pointers.
(d10v_gdbarch_init): Set gdbarch_ptr_bit to 16, so that GDB and
the target agree on how large pointers are. Say that addresses
are 32 bits long. Register the address_to_pointer and
pointer_to_address conversion functions. Since no registers are
convertible now, register generic_register_convertible_not as the
gdbarch_register_convertible method instead of
d10v_register_convertible. Remove registrations for
d10v_register_convert_to_virtual,
d10v_register_convert_to_raw, gdbarch_d10v_make_daddr,
gdbarch_d10v_make_iaddr, gdbarch_d10v_daddr_p,
gdbarch_d10v_iaddr_p, gdbarch_d10v_convert_daddr_to_raw, and
gdbarch_d10v_convert_iaddr_to_raw.
include of "serial.h".
* Makefile.in (remote_utils_h): Update.
* monitor.h (struct serial): Declare as opaque. Remove include of
"serial.h".
(struct monitor_ops): Replace serial_t with `struct serial *'.
* monitor.c (monitor_desc): Ditto.
(read_memory_region, get_descriptor, display_descriptor)
(go32_sldt, go32_sgdt, go32_sidt): New functions.
(top-level): Include ctype.h, utsname.h, dos.h, and go32.h. Ifdef
away `disable' from dos.h, since breakpoint.h defines an enum
member of the same name, and GCC 2.7.2 barfs.
(_initialize_go32_nat): Provide new commands dos-sysinfo, dos-ldt,
dos-gdt, and dos-idt, all of them in the "info" class
Testing: I tested on native Red Hat Linux 7 using gcc 3.0.
The "info float" command exercises print_i387_value.
2001-07-06 Michael Chastain <chastain@redhat.com>
* i387-tdep.c (print_i387_value): Fix pointer glitch.
===
Index: i387-tdep.c
===================================================================
RCS file: /cvs/src/src/gdb/i387-tdep.c,v
retrieving revision 1.11
diff -c -1 -0 -p -r1.11 i387-tdep.c
*** gdb/i387-tdep.c 2001/07/04 21:14:05 1.11
--- gdb/i387-tdep.c 2001/07/06 12:47:00
*************** print_i387_value (char *raw)
*** 163,184 ****
DOUBLEST value;
int len = TARGET_LONG_DOUBLE_BIT / TARGET_CHAR_BIT;
char *tmp = alloca (len);
/* This code only works on targets where ... */
gdb_assert (TARGET_LONG_DOUBLE_FORMAT == &floatformat_i387_ext);
/* Take care of the padding. FP reg is 80 bits. The same value in
memory is 96 bits. */
gdb_assert (FPU_REG_RAW_SIZE < len);
! memcpy (&tmp, raw, FPU_REG_RAW_SIZE);
! memset (&tmp + FPU_REG_RAW_SIZE, 0, len - FPU_REG_RAW_SIZE);
/* Extract the value as a DOUBLEST. */
/* Use extract_floating() rather than floatformat_to_doublest().
The latter is lossy in nature. Once GDB gets a host/target
independent and non-lossy FP it will become possible to bypass
extract_floating() and call floatformat*() directly. Note also
the assumptions about TARGET_LONG_DOUBLE above. */
value = extract_floating (tmp, len);
/* We try to print 19 digits. The last digit may or may not contain
--- 163,184 ----
DOUBLEST value;
int len = TARGET_LONG_DOUBLE_BIT / TARGET_CHAR_BIT;
char *tmp = alloca (len);
/* This code only works on targets where ... */
gdb_assert (TARGET_LONG_DOUBLE_FORMAT == &floatformat_i387_ext);
/* Take care of the padding. FP reg is 80 bits. The same value in
memory is 96 bits. */
gdb_assert (FPU_REG_RAW_SIZE < len);
! memcpy (tmp, raw, FPU_REG_RAW_SIZE);
! memset (tmp + FPU_REG_RAW_SIZE, 0, len - FPU_REG_RAW_SIZE);
/* Extract the value as a DOUBLEST. */
/* Use extract_floating() rather than floatformat_to_doublest().
The latter is lossy in nature. Once GDB gets a host/target
independent and non-lossy FP it will become possible to bypass
extract_floating() and call floatformat*() directly. Note also
the assumptions about TARGET_LONG_DOUBLE above. */
value = extract_floating (tmp, len);
/* We try to print 19 digits. The last digit may or may not contain
commented with "paranoia" into gdb_assert.
(select_event_lwp_callback): Likewise.
(cancel_breakpoints_callback): Bail out early if LP is the event
LWP. Add comment about backup up breakpoints. Fix formatting and
debug message.
(select_event_lwp): Make solely repsonsible for switching event
LWP. Fix formatting and remove bogus "ERROR" debug message.
Don't backup breakpoints from here.
(lin_lwp_wait): Don't touch LP->status, let select_event_lwp
handle that. Only call select_event_lwp if we're not waiting for
a specific LWP, i.e. when PID == -1. Backup breakpoints from here.
* lin-lwp.c: Prevent thread starvation by using a monte carlo
method to choose which of several event threads to handle next.
(stop_wait_callback): Defer pushback of breakpoint events until
later; add SIGTRAP events to the queue of unhandled events.
Keep calling waitpid until SIGSTOP retrieved. If more than one
non-SIGSTOP event is retrieved, push them back onto the process
queue using kill.
(count_events_callback, select_singlestep_lwp_callback,
select_event_lwp_callback, cancel_breakpoints_callback,
select_event_lwp): New functions. Implement monte carlo method
for selecting which of several SIGTRAP threads to handle next.
Push back the breakpoint event for all threads other than the
selected one.
(lin_lwp_wait): Call select_event_lwp to decide which of several
sigtrapped lwps to handle next.
(resume_callback): Disable code that attempts to handle
step_resume breakpoints. Let core gdb handle this.
show_regs, d10v_read_pc, d10v_write_pc, d10v_read_sp,
d10v_write_sp, d10v_write_fp, d10v_read_fp,
d10v_push_return_address): Call the functions d10v_make_daddr,
d10v_make_iaddr, d10v_convert_iaddr_to_raw, and
d10v_convert_daddr_to_raw, not the global macros D10V_MAKE_DADDR,
D10V_MAKE_IADDR, D10V_CONVERT_IADDR_TO_RAW, and
D10V_CONVERT_DADDR_TO_RAW.
structure and not macros.
(Host Definition): Document that much of this chapter is obsolete.
(Target Architecture Definition): Update list of files that make
up a target architecture.
(Coding): Update.
(read_partial_die): Delete fourth argument; we return this info in
the struct partial_die_info object itself now.
(dwarf2_build_psymtabs_hard, scan_partial_symbols): Use the
has_pc_info field of the partial die struct, rather than passing a
variable by reference to read_partial_die.
