land: move WiFi firmware into device tree

product/wifi.mk

@@ -25,5 +25,5 @@ PRODUCT_COPY_FILES += \
 
 PRODUCT_COPY_FILES += \
     $(LOCAL_PATH)/wifi/fstman.ini:system/etc/wifi/fstman.ini \
-    $(TOPDIR)kernel/xiaomi/msm8937/drivers/staging/prima/firmware_bin/WCNSS_cfg.dat:system/etc/firmware/wlan/prima/WCNSS_cfg.dat \
-    $(TOPDIR)kernel/xiaomi/msm8937/drivers/staging/prima/firmware_bin/WCNSS_qcom_cfg.ini:system/etc/wifi/WCNSS_qcom_cfg.ini
+    $(LOCAL_PATH)/wifi/firmware/WCNSS_cfg.dat:system/etc/firmware/wlan/prima/WCNSS_cfg.dat \
+    $(LOCAL_PATH)/wifi/firmware/WCNSS_qcom_cfg.ini:system/etc/wifi/WCNSS_qcom_cfg.ini

wifi/firmware/WCNSS_qcom_cfg.ini

@@ -0,0 +1,483 @@
+# This file allows user to override the factory
+
+# defaults for the WLAN Driver
+
+
+# Enable IMPS or not
+gEnableImps=1
+
+# Enable/Disable Idle Scan
+
+gEnableIdleScan=0
+
+
+# Enable/Disable vsta based on MAX Assoc limit
+gEnableVSTASupport=1
+
+
+# Increase sleep duration (seconds) during IMPS
+# 0 implies no periodic wake up from IMPS. Periodic wakeup is
+# unnecessary if Idle Scan is disabled.
+gImpsModSleepTime=0
+
+
+# Enable BMPS or not
+gEnableBmps=1
+
+# Enable suspend or not
+
+# 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter
+
+gEnableSuspend=3
+
+# Phy Mode (auto, b, g, n, etc)
+# Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac
+gDot11Mode=0
+
+
+# CSR Roaming Enable(1) Disable(0)
+
+gRoamingTime=0
+
+
+# Assigned MAC Addresses - This will be used until NV items are in place
+
+# Each byte of MAC address is represented in Hex format as XX
+
+Intf0MacAddress=000AF58989FF
+Intf1MacAddress=000AF58989FE
+Intf2MacAddress=000AF58989FD
+
+Intf3MacAddress=000AF58989FC
+
+
+# UAPSD service interval for VO,VI, BE, BK traffic
+
+InfraUapsdVoSrvIntv=0
+
+InfraUapsdViSrvIntv=0
+
+InfraUapsdBeSrvIntv=0
+
+InfraUapsdBkSrvIntv=0
+
+# Flag to allow STA send AddTspec even when ACM is Off
+gAddTSWhenACMIsOff=1
+
+# Make 1x1 the default antenna configuration
+
+gNumRxAnt=1
+
+
+# Beacon filtering frequency (unit in beacon intervals)
+
+gNthBeaconFilter=50
+
+
+# Enable WAPI or not
+
+# WAPIIsEnabled=0
+
+
+# Flags to filter Mcast abd Bcast RX packets.
+
+# Value 0: No filtering, 1: Filter all Multicast.
+
+# 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast
+
+McastBcastFilter=3
+
+
+#Flag to enable HostARPOffload feature or not
+
+hostArpOffload=1
+
+
+#Flag to enable HostNSOffload feature or not
+
+hostNSOffload=0
+
+#SoftAP Related Parameters
+
+# AP MAc addr
+
+gAPMacAddr=000AF589dcab
+
+
+# 802.11n Protection flag
+
+gEnableApProt=1
+
+
+#Enable OBSS protection
+
+gEnableApOBSSProt=1
+
+
+#Enable/Disable UAPSD for SoftAP
+
+gEnableApUapsd=1
+
+
+# Fixed Rate
+
+gFixedRate=0
+
+
+# Maximum Tx power
+
+# gTxPowerCap=30
+
+
+# Fragmentation Threshold
+
+# gFragmentationThreshold=2346
+
+
+# RTS threshold
+
+RTSThreshold=2347
+
+
+# Intra-BSS forward
+
+gDisableIntraBssFwd=0
+
+
+# WMM Enable/Disable
+
+WmmIsEnabled=0
+
+
+# 802.11d support
+
+g11dSupportEnabled=1
+
+# 802.11h support
+
+g11hSupportEnabled=1
+
+# ESE Support and fast transition
+EseEnabled=0
+ImplicitQosIsEnabled=0
+gNeighborScanTimerPeriod=200
+
+gNeighborLookupThreshold=76
+gNeighborReassocThreshold=81
+
+gNeighborScanChannelMinTime=20
+gNeighborScanChannelMaxTime=30
+gMaxNeighborReqTries=3
+
+# Legacy (non-ESE, non-802.11r) Fast Roaming Support
+# To enable, set FastRoamEnabled=1
+# To disable, set FastRoamEnabled=0
+FastRoamEnabled=1
+
+#Check if the AP to which we are roaming is better than current AP in terms of RSSI.
+#Checking is disabled if set to Zero.Otherwise it will use this value as to how better 
+#the RSSI of the new/roamable AP should be for roaming
+RoamRssiDiff=3
+
+# If the RSSI of any available candidate is better than currently associated
+# AP by at least gImmediateRoamRssiDiff, then being to roam immediately (without
+# registering for reassoc threshold).
+# NOTE: Value of 0 means that we would register for reassoc threshold.
+gImmediateRoamRssiDiff=10
+
+# To enable, set gRoamIntraBand=1 (Roaming within band)
+# To disable, set gRoamIntraBand=0 (Roaming across band)
+
+gRoamIntraBand=0
+
+#SAP Country code
+
+# Default Country Code is 2 bytes, 3rd byte is optional indoor or out door.
+
+# Example
+
+#   US Indoor, USI
+
+#   Korea Outdoor, KRO
+
+#   Japan without optional byte, JP
+
+#   France without optional byte, FR
+
+#gAPCntryCode=USI
+
+
+#Short Guard Interval Enable/disable
+
+gShortGI20Mhz=1
+
+gShortGI40Mhz=1
+
+
+#Auto Shutdown  Value in seconds. A value of 0 means Auto shutoff is disabled
+
+gAPAutoShutOff=0
+
+
+# SAP auto channel selection configuration
+
+# 0 = disable auto channel selection
+
+# 1 = enable auto channel selection, channel provided by supplicant will be ignored
+
+gApAutoChannelSelection=1
+
+
+# Listen Energy Detect Mode Configuration
+
+# Valid values 0-128
+
+# 128 means disable Energy Detect feature
+
+# 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled.
+
+# 10-128 are reserved.
+
+# The EDET threshold mapping is as follows in 3dB step:
+
+# 0 = -60 dBm
+
+# 1 = -63 dBm
+
+# 2 = -66 dBm
+
+# ...
+
+# 7 = -81 dBm
+
+# 8 = -84 dBm
+
+# 9 = -87 dBm
+
+# Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as:
+
+#
+
+#  Range Loss  (dB)  =  EDET threshold level (dBm) + 97 dBm.
+
+#
+
+gEnablePhyAgcListenMode=128
+
+
+#Preferred channel to start BT AMP AP mode (0 means, any channel)
+
+BtAmpPreferredChannel=0
+
+
+#Preferred band (both or 2.4 only or 5 only)
+
+BandCapability=0
+
+
+#Beacon Early Termination (1 = enable the BET feature, 0 = disable)
+
+enableBeaconEarlyTermination=0
+
+beaconEarlyTerminationWakeInterval=3
+
+
+#Bluetooth Alternate Mac Phy (1 = enable the BT AMP feature, 0 = disable)
+
+gEnableBtAmp=0
+
+
+#SOFTAP Channel Range selection 
+
+gAPChannelSelectStartChannel=1
+
+gAPChannelSelectEndChannel=11
+
+
+#SOFTAP Channel Range selection Operating band
+
+# 0:2.4GHZ 1: LOW-5GHZ 2:MID-5GHZ 3:HIGH-5GHZ 4: 4.9HZ BAND 5: 5GHZ BAND
+
+gAPChannelSelectOperatingBand=0
+
+
+#Channel Bonding
+gChannelBondingMode5GHz=1
+gChannelBondingMode24GHz=1
+
+#Enable Keep alive with non-zero period value
+
+#gStaKeepAlivePeriod = 30
+
+#Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds).
+#For every 10 seconds DUT send Qos Null frame(i.e., Keep Alive frame if link is idle for last 10 seconds.)
+#For both active and power save clients.
+
+#Power save clients: DUT set TIM bit from 10th second onwards and till client honors TIM bit.
+#If doesn't honor for 5 seconds then DUT remove client.
+
+#Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not success still we try on
+#11th second if not tries on 12th and so on till 15th second. Hence before disconnection DUT will send 5 NULL frames.
+#Hence in any case DUT will detect client got removed in (10+5) seconds. i.e., (gGoKeepAlivePeriod + gGoLinkMonitorPeriod)..
+
+#gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and it is period
+#where we send NULL frame.
+
+#gApLinkMonitorPeriod = 10
+
+#gGoLinkMonitorPeriod = 10
+
+#gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame are succeed to send or not.
+#Hence total effective detection time is gGoLinkMonitorPeriod+ gGoKeepAlivePeriod/gApLinkMonitorPeriod+ gApKeepAlivePeriod.
+
+
+gGoKeepAlivePeriod=30
+
+gApKeepAlivePeriod=10
+
+
+#If set will start with active scan after driver load, otherwise will start with
+
+#passive scan to find out the domain
+
+gEnableBypass11d=1
+
+
+#If set to 0, will not scan DFS channels
+
+gEnableDFSChnlScan=1
+
+
+gVhtChannelWidth=2
+gEnableLogp=1
+
+
+# Enable Automatic Tx Power control
+
+gEnableAutomaticTxPowerControl=0
+
+# 0 for OLPC 1 for CLPC and SCPC
+gEnableCloseLoop=1
+
+#Data Inactivity Timeout when in powersave (in ms)
+gDataInactivityTimeout=200
+
+# VHT Tx/Rx MCS values
+# Valid values are 0,1,2. If commented out, the default value is 0.
+# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
+gVhtRxMCS=2
+gVhtTxMCS=2
+
+# Enable CRDA regulatory support by settings default country code
+#gCrdaDefaultCountryCode=TW
+
+# Scan Timing Parameters
+# gPassiveMaxChannelTime=110
+# gPassiveMinChannelTime=60
+# gActiveMaxChannelTime=40
+# gActiveMinChannelTime=20
+
+#If set to 0, MCC is not allowed.
+gEnableMCCMode=1
+
+# 1=enable STBC; 0=disable STBC 
+gEnableRXSTBC=1
+
+# Enable Active mode offload
+gEnableActiveModeOffload=1
+
+#Enable Scan Results Aging based on timer 
+#Timer value is in seconds
+#If Set to 0 it will not enable the feature
+gScanAgingTime=0
+
+#Enable Power saving mechanism Based on Android Framework
+#If set to 0 Driver internally control the Power saving mechanism
+#If set to 1 Android Framwrok control the Power saving mechanism
+isAndroidPsEn=0
+
+#disable LDPC in STA mode if the AP is TXBF capable
+gDisableLDPCWithTxbfAP=1
+
+#Enable thermal mitigation
+gThermalMitigationEnable=1
+
+gEnableFastRoamInConcurrency=1
+
+#List of Country codes for which 11ac needs to be disabled
+#Each country code must be delimited by comma(,)
+gListOfNon11acCountryCode=RU,UA,ZA
+
+#Maxium Channel time in msec
+gMaxMediumTime = 5480
+
+# 802.11K support
+gRrmEnable=1
+gRrmOperChanMax=8
+gRrmNonOperChanMax=8
+gRrmRandIntvl=100
+
+#Scan offload
+gEnableDirectedScanOffload=0
+
+#FlexConnect Power Factor
+#Default is set to 0 (disable)
+gFlexConnectPowerFactor=0
+
+#SAP/P2P-GO mode traffic monitor
+gEnableTrafficMonitor=1
+gTrafficIdleTimeout=3000
+
+#Disable/Enable Strict FCC Regulatory
+# 0 to disable, 1 to enable
+gEnableStrictRegulatoryForFCC=1
+
+#Enable/Disable Modulated DTIM feature
+gEnableModulatedDTIM=3
+
+#max LI value for modulated DTIM
+gMaxLIModulatedDTIM=3
+
+#Enable/Disable Link Layer Statistics Feature
+gEnableLLStats=1
+
+#Enable/Disable EXTScan Feature
+gEnableEXTScan=1
+
+#Enable/Disable TDLS Feature
+gEnableTDLSSupport=1
+
+#Enable/Disable TDLS Implicit Trigger
+gEnableTDLSImplicitTrigger=0
+
+#Enable/Disable TDLS Buffer Sta
+gEnableTDLSBufferSta=1
+
+#Enable/Disable RTS-CTS for HT,VHT
+#Bit mask value to enable RTS/CTS for different modes
+#For 2.4 GHz, HT20 - 0x0001 i.e 1, for 2.4 GHz, HT40 - 0x0002 i.e 2
+#For 2.4 GHz, VHT20 - 0x0004 i.e 4, for 2.4 GHz, VHT40 - 0x0008 i.e 8
+#For 5 GHz, HT20 - 0x0100 i.e 256, for 5 GHz, HT40 - 0x0200 i.e 512
+#For 5 GHz, VHT20 - 0x0400 i.e 1024, for 5 GHz, VHT40 - 0x0800 i.e 2048
+#For 5 GHz, VHT80 - 0x1000 i.e 4096
+#Can be enabled for multiple modes
+#For enabling in both HT20 and HT40 of 2.4 GHz - 0x0003 i.e 3
+#Default is set to 0 (disable)
+gEnableRtsCtsHtVht=0
+
+#Enable delACK
+gEnableDelAck=1
+
+#Compute interval for delack
+gTcpDelAckComputeInterval=2000
+
+#Delack set higher limit
+gTcpDelAckThresholdHigh=17000
+
+#Delack set lower limit
+gTcpDelAckThresholdLow=12000
+
+END
+
+# Note: Configuration parser would not read anything past the END marker
+